I love it when kinda ordinary folks do amazing things that save the kinda average guys like me some money and time. Great video! I hereby subscribe!
@DuctTapeMechanic
Жыл бұрын
Thank you for the support! Much appreciated!
@joella64
4 ай бұрын
Thank you for this video. It showed me this is not a DIY project that I can complete. Will be calling a repair person later today.
@DuctTapeMechanic
4 ай бұрын
You are welcome! Sometimes, knowing when to stop is the best option
@jlemay537
10 ай бұрын
I like the way you showed how to remove the transmission when it was stuck. Nice work
@DuctTapeMechanic
10 ай бұрын
Glad you liked it!
@jasonperry6212
6 ай бұрын
Mine is three years old and just started doing this. At first it was squeaking and grinding like a bearing was going out. A few loads later this noise. Since then I have researched the replacement item and can buy it for around $150. Thanks to you I will be doing it with a handyman coworker at my work. Our shop has all the tools.
@DuctTapeMechanic
6 ай бұрын
You can do it! Good luck!
@coolrobuxgaming
Күн бұрын
Pose video of your machine in the spin cycle because I want to actually hear the machine
@histand
Ай бұрын
This is by far the best, to-the-point guide on replacing the transmission. Fixed for me, too. The most trouble I had was the unit's four bolt sizes for the transmission - not 3/8". I had to work with 10mm. Thanks for the great show!
@DuctTapeMechanic
Ай бұрын
Appreciate the kind words!
@JennyCaldas0506
5 ай бұрын
thank you so much for the video. saved me a lot. it was impossible to remove the transmission from mine. would not budge. finally grabbed a 30 lb. sledge hammer and banged it out to the very end.
@DuctTapeMechanic
5 ай бұрын
I'm glad I could help! Yes, sometimes they are really seized up in there!
@guillermoochoa4851
18 күн бұрын
Great videos very informative, good job
@DuctTapeMechanic
18 күн бұрын
Thank you!
@ChevyARt15
8 ай бұрын
Mine is 3 years old and it just started doing this. Thanks.
@coolrobuxgaming
Күн бұрын
Make a video of it spinning
@staticvoid7814
3 ай бұрын
Excellent video. 9.9/10 just because I had a lot of trouble getting that plastic U-Clip back in the hub but i finally figured it out by shaving with a steak knife and whittling it down and then putting it all the way clicked in before I put the hub down over the transmission i had to force it down but after getting to the end of the job and spending over an hour just on that U-clip. (Last step) i was very relieved to see it was in, then i just tapped it back far enough to get the screw in that slot and I was able to tack it back into place.
@DuctTapeMechanic
3 ай бұрын
Great job getting through it!
@staticvoid7814
3 ай бұрын
@@DuctTapeMechanic thanks man. You’re a scholar
@shawnstone4949
9 ай бұрын
Ours doesn’t make noise while spinning like here…. Buuuuut, damn it makes a super hard knock at the end of spin cycle.. not sure what to do there. Just replaced the dogs in the agitator(noise is not new). I’m guessing it’s some sort of brake? If you have any ideas,I’d appreciate it. I like that fast forward ya got goin’.. cool to watch!
@VincentDzinh
6 күн бұрын
thanks for the video. My problem is when it first 2 spin (when it rinse and spin), it's shaking the machine with a banging loud noise that it move the machine around. However, the last spining ( I assume less heavy load because the water is almost empty) is very quiet. Any advice?
@Relaxation-Clips
5 ай бұрын
Great work and nice video, I do not have the skills like you, I am going with a new machine. Thanks.😀
@DuctTapeMechanic
5 ай бұрын
At least you made an effort! Appreciate the kind words!
@chdurango59
Жыл бұрын
I would love to see the transmission repair. My transmission has rusted splines😢
@ChannelEleven59
2 ай бұрын
Thank you sir. Mine is doing this and I cant afford a new one right now.
@coolrobuxgaming
Күн бұрын
Post a video of your washing machine spinning so I can hear what it sounds like
@thethree300exriders
16 күн бұрын
My mvwc565fw1 maytag washer bangs around even with no clothes in it. Replaced springs already same thing thing. What could be the problem. Would a bad transmission cause this?
@stuuuporman
11 ай бұрын
Excellent video. Thanks!
@homeandbackyard9599
4 ай бұрын
My whirpool not only made loud noise, it shifted as well and cloth were not draining if I used large and super load.
@KommonCents_
6 ай бұрын
I encountered this problem after I replaced the actuator on my washer. That's crazy if my sealed bearings went the very next wash cycle after I replaced the actuator/tachometer
@DuctTapeMechanic
6 ай бұрын
Stanger indeed!
@coolrobuxgaming
19 сағат бұрын
Post a video of your machine and provide the model number
@rickmcclelland2576
2 ай бұрын
My whirlpool washer only screams during the braking cycle of spin, when it is trying to slow the tub from spinning. Any ideas. Is that a transmission issue as well?
@susanvaughn741
8 ай бұрын
The bearings are probably common. I’d like to see you try to replace them after removing trans and shaft. Might need a press.
@terrypasteur7650
7 ай бұрын
You dont replace the bearings ,they are in the gearcase
@terrypasteur7650
7 ай бұрын
Also replace the tub seal
@Merabbit
5 ай бұрын
Never buying Maytag again, this thing hasn’t lasted 3 years and it’s already falling apart.
@staticvoid7814
3 ай бұрын
You must not be using it right. Ive had mine 12 years and the bearings just now started getting loud so I did what this video told me to and I cleaned everything while i had it apart and by god it runs, smells🙃, sounds, looks, and feels like brand new
@coolrobuxgaming
Күн бұрын
Post video of machine spinning
@coolrobuxgaming
19 сағат бұрын
@@staticvoid7814What model number is your machine?
@coolrobuxgaming
19 сағат бұрын
@@staticvoid7814What is your model number on your washer?
@tatchik77
5 ай бұрын
Mine squeals when it spins, even when I turn it by hand. Any suggestions on why that might be? I've already changed the seals & bearings.
@marcomunoz8059
2 ай бұрын
Can I do the same with my g e washer
@DuctTapeMechanic
2 ай бұрын
New style ge washers are very similar
@dancelife3440
5 ай бұрын
love the name of your channel
@DuctTapeMechanic
5 ай бұрын
Thank you!
@leeb.7188
3 ай бұрын
I have an washer that just started doing this. It’s an older top-loading Frigidaire. It doesn’t have the sealed transmission box like this one. I’m looking for a video on how to fix it. I think it will be more complex than this repair, unfortunately.
@coolrobuxgaming
Күн бұрын
Post video of machine on spin
@arghdub_1123
11 ай бұрын
So if I don’t have the extra $175 available till next payday(not for two weeks) and I can deal with the loud noise, is it ok to use the washer??? Basically, is it just annoying but since I can deal with the freight train in my washroom, it’s ok to wash clothes??? Really appreciate anyone that helps with their knowledge!
@DuctTapeMechanic
11 ай бұрын
Eventually, the bearings will seize, and the drum will stop spinning (might also damage the tub seal/tub). Will that happen in two weeks? Probably not, but don't hold me to it, lol!
@arghdub_1123
11 ай бұрын
@@DuctTapeMechanic thx for the speedy reply… greatly appreciated!!!
@MayorofNumber3
10 ай бұрын
Mine has been like this for about 2 years now. Works fine just loud as hell. I just leave the house when the machine is running lol
@coolrobuxgaming
Күн бұрын
@@arghdub_1123Give me video of your washer
@coolrobuxgaming
Күн бұрын
@@MayorofNumber3Give me a video of your washer in the spin cycle
@billyobrien3557
8 ай бұрын
Very helpful video I have subscribed
@DuctTapeMechanic
8 ай бұрын
Thank you!
@billyobrien3557
8 ай бұрын
If you make a video of the bearing replacement I would love to see it if they even make a bearing that you can buy for that
@kevinwilliams7061
9 ай бұрын
What if it makes a grinding/screeching noise at the end of the spin cycle?
@jonboy2771
9 ай бұрын
I have same problem
@Magasplaylist
8 ай бұрын
Mine did the same. I changed the pulley belt and solved the noise.
@denisetruax2765
Жыл бұрын
Thanks so much very helpful
@DuctTapeMechanic
Жыл бұрын
You're welcome!
@jasonkatz9727
Жыл бұрын
Thanks, my toploading Maytag screeches during spin cycle. Could it be the same problem? Also there is no tag with serial number on machine.
@DuctTapeMechanic
Жыл бұрын
Most likely the same issue, particularly of you have a machine with 6 led lights followed by a pause play button (they are all made by whirlpool)
@shawnstone4949
9 ай бұрын
Check right underneath your lid… back side of the washer,top side of the drum,it’s kinda hidden…..ours had a upc,along with model number
@marcellablankenship4390
10 ай бұрын
Mine sounds like its slipping and never engages in a full fast spin. Cranks up to spin, makes an awful noise and just lets it free spin until it winds down. Could this be the problem?
@DuctTapeMechanic
10 ай бұрын
It sounds like an issue with the clutch (which is a much easier repair). Check out my video on it!: kzitem.info/news/bejne/pJx6zqKnrKigrIo
@marcellablankenship4390
10 ай бұрын
@@DuctTapeMechanic Thank you! I will do that!
@MrSpaceRangers
7 ай бұрын
great video thanks
@DuctTapeMechanic
7 ай бұрын
Your welcome!
@coolrobuxgaming
Жыл бұрын
I have the same washer and it makes the same noise when it spins
@DuctTapeMechanic
Жыл бұрын
Bad bearing/transmission
@coolrobuxgaming
Жыл бұрын
@@DuctTapeMechanic Bearing failure is very common on this particular washer
@eddietorres14
4 ай бұрын
What causes the bearings to go bad? I have a whirlpool doing this and it’s only two years old.
@DuctTapeMechanic
4 ай бұрын
Poor quality bearings!
@coolrobuxgaming
Күн бұрын
Post a video of the machine spinning
@al52269
7 ай бұрын
Great video. Thanks for sharing. New subscriber here
@DuctTapeMechanic
7 ай бұрын
Thanks for the support!
@w7y3a2t6t1
9 ай бұрын
How can i test the spin or rinse spins without putting water on it? So i can fix and work on it much better
@DuctTapeMechanic
9 ай бұрын
There is a manual test mode that you can out the washing machine into which will allow you to test the spin and drain without water. There are a lot of good videos/instructions online on how to get into manual test mode. Perhaps I'll make a video on it in the future.
@w7y3a2t6t1
9 ай бұрын
@@DuctTapeMechanic awesome sounds great thank you,it would be great to see a more detailed video and description into the manual test to know more about it and what to do and not to, in my case i just dismantled everything since well it seems it turned out to be the transmission after i bought the 2 pieces that we're above and below of it 😅 so yeap another washing machine cause Damm whirlpools are annoying
@angelurias4502
Жыл бұрын
I have a whirlpool washer that makes a horrible grinding noise at the end of the spin cycle not during any idea ?
@cvas282
Жыл бұрын
Most likely the shift actuator. The part he pulls off at 3:30 in this video
@JohnAdams1-y5w
Ай бұрын
My washer is really loud in the spin cycle, I do have some videos of my washing machine spinning that you can watch:
@JohnAdams1-y5w
Ай бұрын
This is what it sounds like: kzitem.info/news/bejne/zYVt14h6n6WpgGUsi=_TzmXXzdylO_bgi4
@DuctTapeMechanic
Ай бұрын
Sounds like a bad transmission, but I can't say for certain without being there. Try spinning the basket with your hand and listening for a howling noise
@JohnAdams1-y5w
Ай бұрын
@@DuctTapeMechanic It did make a howling noise when spinning it by hand
@DuctTapeMechanic
Ай бұрын
@@JohnAdams1-y5w bad bearing in transmission
@rockerbigjoe5711
10 ай бұрын
What is the trick to get the wash plate out of a rusted spindle?
@DuctTapeMechanic
10 ай бұрын
Wd40 and a lot of rocking the wash plate up and down
@homeguestunton
Жыл бұрын
My Crosley sounds like a freight train in the spin cycle
@DuctTapeMechanic
Жыл бұрын
Most likely bad bearings
@abebayehubecho2126
Жыл бұрын
Very helpful
@DuctTapeMechanic
Жыл бұрын
Thank you!
@GRobledo512
5 ай бұрын
Might as well replace the washer lol
@DuctTapeMechanic
5 ай бұрын
Aaaah then you haven't seen my video in which I actually rebuilt one of these transmissions.
@YOGiiZA
11 ай бұрын
solid
@raymondpitts5105
8 ай бұрын
Fantastic video this is exactly what's wrong with my washing machine but how do I reach him? I want to talk to him and see if he would be able to come and repair mine but I have not been able to find any way to contact him does anybody know? 🤷🏾♂️🤷🏾♂️🤷🏾♂️🤷🏾♂️🤷🏾♂️Does he have an email address or a phone number there's nothing listed on these videos!!!🤬😬😡🤦🏽🤦🏽☹️☹️
@coolrobuxgaming
19 сағат бұрын
Post video of your machine spinning, also provide model number of your washer.
@lindahoffman3691
11 күн бұрын
That’s a lot of work. I will never buy a Whirlpool again
@DuctTapeMechanic
10 күн бұрын
Unfortunately, quality has gone down across all brands...
@modeljetjuggernaut4864
7 ай бұрын
Diy milestone
@jackiechain27
11 ай бұрын
What’s the part number
@DuctTapeMechanic
11 ай бұрын
Best thing to do is look at the part number on the transmission you are removing
@lindahoffman3691
Ай бұрын
This is too much! My machine is a Whirlpool, not even a year old, and making a sound just like in the video! I’m sick of it and will never buy another Whirlpool ever again!
@coolrobuxgaming
Күн бұрын
Post a video of your washing machine in the spin cycle, I want to hear what it sounds like
Пікірлер: 108