Several years later still helping fix pumps. LEGEND
@stanko7302
9 жыл бұрын
thanks to the vid i was able to reseal my pump and now its better than ever. Only 30 pumps from 1k psi to 2k psi, before it used to take almost 70 pumps. I ended up replacing all the cheap buna o-rings with 90 duro urethane so it should last much longer. If you still can't figure out how to fix it after watching the vid you should look at a diagram of it online
@johnwilliams40
9 жыл бұрын
thanks zacko,....your info really helped in my rebuild-working as it should now,....my white o-ring was fine ,it was an o-ring in the bottom brass piece ,inside, that was torn-it looks as if whoever put my pump together did not seat the o-ring in the inner groove like it should have been and it was torn,...johnw.
@varminthunter1342
5 жыл бұрын
Video tips a wide angle set up and back off from close up shots, you can edit it with close up shots from your camera smartphone.Buy a longer whip with dual male universal setup to extend the wip.,then set up the Tanks in a slant vertical set up laid down on a pillow etc, to watch the air psi gauge.
@Jpm4231
2 жыл бұрын
Overall helpful but at the most crucial part your pump was out of the camera view
@guitarmaho1
7 жыл бұрын
I for got to put that white plastic washer back did'nt feel like tearing it down again and it still pumps just fine 'i'll put it back next time I rebuild it Thanks for video help me out alot
@Pangolin14
9 жыл бұрын
Thaks to this vid i fixed my pump, thank you!
@enriqueoliva6988
2 жыл бұрын
I don't know but the tank guage did not move after you pump it and the pump external tube goes up on its own indicates it need another reseal/overhaul.
@65LB
6 жыл бұрын
Too bad the camera is pointed off from where the action is
@parrotbill
7 жыл бұрын
I used my pump a few times...less than a dozen times and let it set for a year and now it won't pump up the gun...no pressure. It shouldn't break down that fast, should it?
@anirudhpanwar6202
8 жыл бұрын
please elaborate on the part where the o ring of the last stage is replaced,the video wasnt clear.i have to do the same with my hills pump.how shud i remove the main(and the smallest o ring) which is in the last stage which is the thinnest pipe.
@tattooglisha
8 жыл бұрын
try to film what you are doing pls.
@I8THEmagictoaster
9 жыл бұрын
can you give me the dimension of the Benjamin Hand pump's when its fully extended and fully compressed please.
@angelguzman4955
6 жыл бұрын
Mine the trheads are triped i guess thats wat is called it wont tight any more where the presure gage goes. Is there anything i can do there us gule or something or just buy another one any sugestions?
@tsisyoojyim3875
7 жыл бұрын
After pumping I open the air relief button to let air loosen, but drawn all air out from the rifle. Anyone know whether something wrong with the gun or the pumper?
@Prairiedrifter1
5 жыл бұрын
Nice socks
@jaspergreen4744
8 жыл бұрын
did the metal washer work
@dwightkirkendoll6198
3 жыл бұрын
I was pumping up my PC P air rifle the female popped off as I was pumping it up now my pump is not working I replace the holes do anyone have any ideal
@frankl1955
4 жыл бұрын
Great video, thanks. Is your hard to pull up? I'm trying to decide if I should send this back.
@jamienicole201
3 жыл бұрын
Did you figure out why? Mine is hard to pull up and gets stuck
@bigdaddywoowooo4631
8 жыл бұрын
You were at a 1000 psi with the camera angle, pumped it about 70 times, and were still at 1000? Thanks for taking it apart, but it sure doesn't look like you fixed it. 14 pumps up and down should equal 100 psi fyi
@dannydoyle1973
7 жыл бұрын
did the washer work?
@whipplewatson8920
10 жыл бұрын
What's their contact info to get the seals?
@2011wideglide
10 жыл бұрын
I was hoping to find someone with a video of the breaking down of this pump. But sorry to say bad camera work. Most of the stuff is off camera. : (
@ZaCkOX900
10 жыл бұрын
True, it needs to be really high, I also didn't have time to film this properly sorry. However, if you listen to what I say you should be able to fix it.
@2DangerousDan
7 жыл бұрын
It doesn't take any longer to film om camera or off camera, just takes a little awareness!
@elcompamartinez2647
6 жыл бұрын
not true!!
@birdchaser2010
10 жыл бұрын
help I lost my bleed valve
@jvernonruth2544
7 жыл бұрын
Terrible camera work. Most of what I want to see is missing..!!!!
@ZaCkOX900
7 жыл бұрын
Sorry at that time, I could not see what was happening but I did describe what to do. There should be better pumps, 3 years later. Fixing this one is maintenance way too often.
@jvernonruth2544
7 жыл бұрын
Your efforts to make this video are greatly appreciated.... in spite of how it turned out. Appreciated as well are your candid comments on how frequently this pump need 'maintenance'. I suppose "You only get what you pay for" applies here as well. lol
@Skaetdude
9 жыл бұрын
I was going to buy this same pump off someone but he says the gauge needs to be replaced,is that possible? Thanks
@josephjaalouk
2 жыл бұрын
Most of your video is of the frame 🤣
@garygallant5390
8 жыл бұрын
Sure takes the fun out of shooting.
@aeolusrme
10 жыл бұрын
where is the link?
@ZaCkOX900
10 жыл бұрын
Sorry, I added the link just now in the description, there is a phone number in the thread page 2.
@aeolusrme
10 жыл бұрын
ZaCkO awesome... Thanks!
@65LB
5 жыл бұрын
too bad it is not in frame
@varminthunter1342
5 жыл бұрын
Wow so many Videos of the Pump but nothing about any problems in the lower tank itself.any problems with the tank not the shaft.I heard a pop in my tank when I was on the down stroke filling my PCP rifle tank to 3000k and it popped.So I called cossman and they sadi mail it to them to troubleshoot and if any repairs can be made or sell one and shipping both ways on my dime.The Pump was on a chicken shit 90 day warranty .So I bet the Pump and parts come from China.
@tonyorabona594
8 жыл бұрын
CANT SEE WHAT YOUR DOING TOO BAD YOU HAD A CHANCE TO GET PAID YOU BLEW IT NEXT TIME MAKE SURE YOUR EFFORTS ARE EASY TO SEE NOT OUT OF FRAME
Пікірлер: 41