Bridging the reset pins didn't work for me either; the multimeter was testing the pack at just over 20V, when it should operate at 28.8V. What finally worked for me was inserting and removing the barrel plug (charger) several times in a row to initiate a charging cycle - it started charging properly after doing this 5-6 times in row.
@GavinSeim
6 ай бұрын
Always come back to this and it works. The two contacts have never worked for me. I use am adjustable power box at 30V and have to get the battery voltage back up to about 25V before the read light comes back on and then it will charge again.
@andrewmurdock
4 ай бұрын
can you do a video explain this
@alexmoon4638
2 жыл бұрын
What wire are you using to charge it? I’m assuming a paper clip won’t work lol
@holstfly1
3 ай бұрын
Hey boss quick question, I have one that I'm trying to fix the batteries are fine, but when I switch it on, the screen just gives me a quick flash, and then it turns off. Have you had any issues of that?
@cce7087
Жыл бұрын
I was able to do this with a drill battery. Connecting two wires - one from positive to positive and one to neg/neg. I am in the UK and wasn't until using a 240 volt with risk of arc and injury. I think the risk is still there with a wall socket in North America and a drill battery is a lot easier. I connected them for several minutes and then checked and it was good to go. That was after the battery sitting for years!
@cirkonneon9976
2 жыл бұрын
Did You solder the two red wires? Or manufacturer did it?
@GFOCUS
3 жыл бұрын
Informative and This is a good and tricky video for video for #Godox #AD600 users.
@udaraathukorala7268
Жыл бұрын
Thank you fixed my problem by using the charger on plus and minus connectors.
@scottishphotographer
Жыл бұрын
Thank you! Worked for me when the 'bridging' method on its own didn't.
@myof
Жыл бұрын
Thanks Giri!!! I tried the other method of bridging the points with no luck. Tried your method. It didn't work the first time, powered everything off - as you suggested - tried again and its working! Charging like normal now😄
@girifilmmaking6240
Жыл бұрын
😍Glad to hear that👍
@ladyninjabikergirl
Жыл бұрын
You man!!!! The pin method was not working for me. New strobes from late 2022. Both dead batteries after christmas break. Im so grateful for you help! Thank you for sharing! I used the black twist tingy for cables, that comes with the charger. Make good flat contact and wait a few seconds then the lights came on! Amazing!
@girifilmmaking6240
Жыл бұрын
Wonderful 👍 . Thanks mate🙂
@grocharon7000
21 күн бұрын
Your fix worked for me. Thank you!
@CarinaChatel
2 жыл бұрын
I just tried and the charger did respond but it’s not going up and down, first time i saw the first one green led then I did it again I saw the last one and I tried it again and I saw the 2 in the middle and right now the first 3 but always not moving… I don’t know what to do 😩
@girifilmmaking6240
2 жыл бұрын
Same thing happened to me. I turned off everything, and repeated the entire process. And it worked.
@CarinaChatel
2 жыл бұрын
@@girifilmmaking6240 thank you for you quick reply. I turned off everything several times and did it again but I will try again ! I will let you know
@CarinaChatel
2 жыл бұрын
@@girifilmmaking6240 Ok so I took another charger because I have another same flash unit and it’s going up and down 😬 so it seems to work !! Thank you so much
@girifilmmaking6240
2 жыл бұрын
@@CarinaChatel Wonderful 😀
@honeyofficial9409
2 жыл бұрын
I also decided to disassemble my battery, but for some reason I have it a little different from what you have on the video, tell me what should I do? I have only one hole, in the place where the second one should be - some kind of strange white filling, I allow it to be opened, but there is no hole under it, on the contrary, there is some kind of convex object 🤯
@girifilmmaking6240
2 жыл бұрын
Honestly, No idea bro. Do you have the same series?
@Elon600
2 жыл бұрын
Thank you sooo much this video saved my battery all other videos I saw were not helpful
@girifilmmaking6240
2 жыл бұрын
🤩Happy to hear that.
@JayneChong
8 ай бұрын
Omgosh this finally worked after weeks of searching! Definitely sketchy at first but I was desperate. Since I didn't have fancy wire or alligator clips, I used paper clip! The first time it didn't work. The charger did start to do something super weird where the power light would turn off and on and then the green light loads up while the +/- was still touched. I tried to plug it in. Didn't work. Even tried the plug in/out method. Tried it again but with more time + all the methods combined. I held it on for longer and watched the charger load and do the weird thing again a few more times. This time, small sparks appeared 2-3x when the red light went in and out. I also did the whole touching points showed in the first part of the video. I used a tweezer to touch the 2 hole points (corner of circuit for ad400) as well and there's 2 tiny button by the indicator, i clicked those as well. I unplugged the charger, making sure the light is fully gone. Plugged it into the battery before powering the charger. The charger did the weird thing where red and green light would go in and out then green light, 1 bar, stayed on for a few minutes. I just let it be. Now it's charging perfectly fine. :) Mine is the AD400Pro battery (circuit is on the side)
@Kestisr
Жыл бұрын
Thx you very much. Only yours video realy work and help!!! Thx!
@SlowLiving-l8l
2 күн бұрын
Yes,yes,yes this clip work for me too, Thank you very much.❤
@kamarajkm
Жыл бұрын
Wish it will work with my AD600Pro Battery which wasn’t used for about two years, fingers crossed
@MuhammadAsif-xh6wp
2 жыл бұрын
😍🥰🤩 thanks sir a lot , you just did it , ! 👍👍👍👍👍👍👍👍
@girifilmmaking6240
2 жыл бұрын
Happy to hear that bro🙂
@Enzor1515
2 жыл бұрын
Much appreciate it! It definitely worked!
@girifilmmaking6240
2 жыл бұрын
Cheers😀
@ericvink2145
Жыл бұрын
Dank je wel...deze informatie heeft er voor gezorgd, dat ik mijn accu van de AD400 weer op kan laden.
@frustycreations4610
2 жыл бұрын
thanks it worked actually
@girifilmmaking6240
2 жыл бұрын
Good to hear that❤️
@mg_movealong438
Жыл бұрын
man - You're a money/ battery saver :) thank You :)
@charlie25756
2 жыл бұрын
It work for me, thank you very much 🙂
@girifilmmaking6240
2 жыл бұрын
😀
@chrissallis5222
2 жыл бұрын
Thank you so much this worked for me too
@girifilmmaking6240
2 жыл бұрын
😀
@richardsongo41
2 жыл бұрын
This worked for me. The bridge on its own was not enough. Thank you so much.
@CarinaChatel
2 жыл бұрын
Can I ask you what kind of connecting wire did you use? I have the same problem
@richardsongo41
2 жыл бұрын
@@CarinaChatel I used a metal paper clip with an alligator clip, followed instructions provided here and it worked. Instructions on other videos didn’t work for me.
@girifilmmaking6240
2 жыл бұрын
Good to hear that it helped😀
@Lizarjuan
Жыл бұрын
This one work very well thank you
@chandragurung3013
Жыл бұрын
Thank you man, it worked!
@xavierchanut6835
Жыл бұрын
Wow,Thank you sir!
@bornie2014
Жыл бұрын
Dude you are a genius ! thanks !
@ryanphotostudio
2 жыл бұрын
Thank you so much this is genius! my battery is charging and my shoot can go ahead. Thank you again
@girifilmmaking6240
2 жыл бұрын
Good to hear that😀👍
@sporsterchop
2 жыл бұрын
Thank you so much
@girifilmmaking6240
2 жыл бұрын
Hope it helped 🙂
@kelvinlearnsinvesting8678
2 жыл бұрын
Telegram name?
@manju27kiran
Жыл бұрын
Thank you so much Giri, found your method explained in the video to be the most reliable and easiest approach to jump start my AD400 Pro dormant battery back to life!! 🙏🏽 Now my battery is charging like before 😃
Пікірлер: 57