Well done for doing the clutch replacement in your driveway. Only use 1st gear for steep hills or ramps, try taking off in 2nd gear when on flat ground.
@elheffeschopshop
3 жыл бұрын
Thanks man it was a bit of a nightmare! Yeah been driving around in second since i worked.out its 5:1 haha
@Garage.Philosophy
3 жыл бұрын
Aslong as the access is okay with the cab tilted was it not that bad of a job ! Luckily you didn’t get any rusted bolts good job man
@elheffeschopshop
3 жыл бұрын
Yeah the cab tilt was good for the top bolts and letting light in! Thanks dude it was a mission
@IndianTruckWorkshop
3 жыл бұрын
Great work brother 👍👍👍
@elheffeschopshop
3 жыл бұрын
Thanks mate, it was a mission
@jamesmckinnon7299
3 жыл бұрын
Your the man El Heffe
@elheffeschopshop
3 жыл бұрын
Thanks tug6 😅
@xaviergonzalez5145
2 жыл бұрын
Nice video bro! I got a light truck (5 ton) and when its not loaded the truck has power. But when you load the truck up it has no power on uphills... do you think the clutch is not working ? Or do I have to find the problem in another system???
@elheffeschopshop
2 жыл бұрын
If the revs climb quicker than the speed the clutch is slipping but youd probably smell that Boost leak maybe?
@WaddupBoi
Жыл бұрын
thanks the video. i'm doing a npr66 and having an absolutely fucked time getting the flywheel bolts off. tried the same tech of grounding the 22mm down a bit but my gun isn't strong enough to break it loose. tried a big ol breaker bar and the jack pipe but i'm closing to snapping the breaker bar than breaking the bolts loose. i think the previous mechanics loctited the bolts lol.
@elheffeschopshop
Жыл бұрын
Oh wow! Thats missery! I found the thicker socket worked onnthe rattle gun, i assume because it lost less force through the socket, you might have to get a torque multiplier or another breaker bar -.- what a pain! I feel for you ahah
@WaddupBoi
Жыл бұрын
@@elheffeschopshop Managed in the end to get them loose with a neighbours air gun. How did you go about getting the input shaft to slide in? did you have an alignment tool? I had to use a diy method with an extension and tape and am doubting it's properly aligned...
@elheffeschopshop
Жыл бұрын
Nice work! I didnt document this very well tbh I put the clutch etc in the gearbox Bolted the gbox up. Then through the starter hole did all the clutch bolts up, it was misery 😅
@elheffeschopshop
Жыл бұрын
Funnily enough fighting the same issure right now on a different car ahah
@WaddupBoi
Жыл бұрын
Ahh that makes sense, I'll give that a go, hopefully everything is smooth sailing once the two bits are mated. Certainly don't envy you mate, these jobs are a pain
@derrickmorrison5701
Жыл бұрын
Is there a adjustment for a 1990 clutch
@elheffeschopshop
Жыл бұрын
Im not syre sorry mate i imagine there would be a bleeder somewhere
@kuengyal23
Жыл бұрын
What’s the torque for pressure plates ?
@elheffeschopshop
Жыл бұрын
I cannot remember sorry mate, i rang isuzu for the torque spevs
@Glenjimen
3 жыл бұрын
Maybe a Onlyfans would be more successful with your Carwash Antics 😳
Пікірлер: 25