The Roosa master fuel pump was leaking badly, turned out to be a simple fix. My other channel (Angry Ram) - • What happens when you ... Mrs Marty T. • Time lapse Painting of...
Automotive engineers around the world were shrieking with rage when you were able to slide that throttle shaft out without dismantling the entire machine...
@Cole-xq2tl
2 жыл бұрын
They didn't start making those types of engineers until 1999!
@cg8469
2 жыл бұрын
It is amazing to me how universal these problems are.
@warrensteel9954
2 жыл бұрын
You mean dealerships around the world are shrieking. Dealerships want things so complicated and proprietary that you can't work on them and have to bring it in for work. Dealerships tell the manufacturers they need more money and the manufacturers tell the engineers to make it more complicated. John Deer is constantly working on software that makes it almost impossible to fix your own equipment.
@PaulRansonArt
2 жыл бұрын
Taking thigs one step further. Dealerships would have firstly charged you for plugged in a diagnostic computer to tell them you had low fuel pressure despite seeing the fuel peeing out of the pump on to their nice painted floor 🤑🤑 Then replaced the sensors, ECU and all the wiring before finally deciding that it needed a new pump because its a sealed unit 😣😣
@jamesa7506
2 жыл бұрын
"What are we going to do today Brain?" "Same thing we do every day, Pinky, try and take over the world..."
@michaelturner1565
2 жыл бұрын
As someone who owns an automotive shop and works on cars all day, I appreciate your videos. Watching you trying to get that allen wrench in made my teeth hurt. I empathize. You give me hope. When I'm up against a car that's fighting me, I watch a video of you working on something up to your arse in bushes and thorns and lying in the dirt I find the strength to persevere with my hoist and well lit shop : )
@jimr118
2 жыл бұрын
@@taxesdeathandtrouble.1886 and someone to fix the generator and the chopsaw when they break...
@dickgoodey2528
2 жыл бұрын
Your methodical methods pay dividends again. I think if I had been doing this job I would have taken the whole pump off and worked on a bench, thus causing myself a lot of extra work. Marty wins yet again. Good man.
@zzota
2 жыл бұрын
Yes, that would have been my first move too. Marty's the man for simple and effective fixes!
@coolhanddruid
2 жыл бұрын
90% of the time if you hadn't of taken the pump off, you would have been all careful not to drop anything, then once you slid the shaft out, it would have hit the engine block on the last little bit, and not came out, then you would have half wasted that time, cause you have to pull the pump anyhow.
@kragfearghal
2 жыл бұрын
Agreed he's amazing at repairing his lost/found equipment, love his videos.
@JHruby
2 жыл бұрын
Terrific fix. Have to say in the first video I was worried that pump was leaking from the shaft and that would have been a lot more involved. Great simple fix in a tight spot. This is going to be a good machine.
@dfishpool7052
2 жыл бұрын
Some nice work done here Marty - and no parts dropped - it was a bit of a cliff hanger watching the removal of those very small bits and pieces. Your deftness would come in very handy if you took up another career in bomb disposal!!! Thanks for the video - love the sound of that diesel.
@Gotblade
2 жыл бұрын
Your meticulous patients is quite pleasent to watch! Very unlike the angry clumsiness that I associate with anything mechanical like that. You set a great example ❤
@andyanderson25
2 жыл бұрын
I thought I'd like to video myself fixing some of my old bits of gear. then I realised it would be mostly be me swearing and walking around looking for my tools
@Gotblade
2 жыл бұрын
@@andyanderson25 😂 Exactly! That could be entertaining but I don't miss Orange county Choppers. If I was a father I would want to be like Marty.
@99cachorro
2 жыл бұрын
@@andyanderson25 hahahha me too me too, and I have a very large yard to look for stuff
@Gotblade
2 жыл бұрын
@@99cachorro Awesome!
@DovetailTimberworks
2 жыл бұрын
Nice fix! Those O-ring kits sure are handy to have on the shelf for when you need them.
@marcryvon
2 жыл бұрын
Through the years, I've been swearing looking for the right O ring, never to be found till I saw such a big kit at a car parts store. Bought it on the spot for only a few bucks. What a game changer ! My DIY life now is good ! 😊
@mcflapper7591
2 жыл бұрын
Yeah. If it's not the Chinese o-rings one that dissolves after some time in diesel care..
@davidp8157
2 жыл бұрын
@@marcryvon and, you can always make the right size if it's an oddball, by grabbing one or two the right Thickness, slice and add or remove length, then CA glue the ends, even professionals do this in a bind in the field. It works , try it!
@davidp8157
2 жыл бұрын
@@mcflapper7591 get the nitrile or Viton version, not much difference in price when you can get them, then you are good to go
@davidp8157
2 жыл бұрын
@@mcflapper7591 get the nitrile or Viton version, not much difference in price when you can get them, then you are good to go
@garyholt4445
4 ай бұрын
I admire the fact that you can work with small intricate parts in tight spaces and not drop or lose anything. I would be hopeless doing what you are doing.
@donnaml8776
2 жыл бұрын
You and your wife have wonderful qualities to pass onto your children; patience, kindness, caring for others, etc. Everyone can see it through the work you do.
@burlatsdemontaigne6147
2 жыл бұрын
plus caring for machinery!
@donnaml8776
2 жыл бұрын
@@burlatsdemontaigne6147 absolutely! And a very good job at that! 😃
@jesseasher7520
2 жыл бұрын
Hi Marty, just a tip for sliding O rings/seals etc over rough/sharp surfaces. - If you cut a rectangle of plastic out of an old soda/milk carton, grease one side and wrap it around the shaft, you can slide the O ring/seal over the plastic without risk of damage on rough/sharp surfaces. Then just slide it into its seat and remove the plastic. This works especially well for fork legs/hydraulic arms where the chrome may be pitted or corroded. :)
@MartyT
2 жыл бұрын
Good tip thanks
@waynep343
2 жыл бұрын
Tip. I have several pair of 11" long offset needle nose pliers. Have a 20 degree offset to them. I took a small chainsaw file and carved shallow grooves inside each tip leaving about 1/4" undamaged. They come in so handy for pulling pins. Gripping round stuff like bolts or shafts. Can also pickup amazingly heavy round items.
@jameskurdy4873
2 жыл бұрын
Great idea
@EvatronX
2 жыл бұрын
most evenings i make a cup of tea and watch this machine wizard work its so satisfying
@Matty.Hill_87
2 жыл бұрын
I've just found your channel, so far today I've watched you fix 3 tractors, a fuel pump and attempt to get the terex running 🤣🤣
@andrewrobinson2869
2 жыл бұрын
Great work Marty. So many would take it to a mechanic. You show that with a open mind and the guts to try . You overcome most obstacles yourself. Only way to learn. I bet your kids will be just as good. Keep up the great work . Regards Andy Australia
@adambassador7727
2 жыл бұрын
The flies buzzing by, the roosters in the background, the birds in the trees...and I can feel the sun on your back, as you diligently work to fix something that was left for dead on the hillside. Job done, indeed, Marty. 👍 ...Really a great (and peaceful) video to watch ✌
@machinist5828
2 жыл бұрын
Marty that was pleasing to watch. I used to have hands like that but now it's not so easy. Between nerve damage from carpal tunnel, neuropathy and arthritis my hands are becoming unusable every day. It's a maddening process to see the function of my hands slowly deteriorate and have no control or cure. I'm 63 and retired so for now I can go slow and keep a good supply of pliers, tweezers and magnets handy. I approach everything I do as if I am going to drop it and plan accordingly. Be kind to your hands. If you start having symptoms of carpal get it taken care of. I was in the military and they dinked around too long getting them fixed. Nice fix on a beautiful old machine. As always I'm looking forward to your next episode of "Marty, machine whisperer!". LOL! Cheers from South Carolina USA Terry
@davidp8157
2 жыл бұрын
I was 51 when heart issue was diagnosed, started taking meds for that, 3 days later the first of a serries of major strokes, still ongoing small ones daily almost 3 years later, left side semi functional but try holding and doing anything with a pair of pliers with my left hand and I would be better getting a 2 year old to do it. Luckily right side still functioning pretty good , but lots of things require two hands, left to hold, and right to do whatever . Talk about frustration... . Feel for you and anyone in similar situation
@machinist5828
2 жыл бұрын
@@davidp8157 yep I feel for you too brother. I have a good friend that I call my "Brother in junk". I have bought so much stuff from him over the last 20 years it's ridiculous. He has had cancer, prostate trouble and several strokes all in two years. I have seen him go from tinkering all day I the shop to sitting in a recliner. It breaks my heart because he can sit there at the window and look at all the stuff he was going to do. I call him every day and give him an update as to what I've been up to. He has 12 years on me but it's sad it happened so fast. Yep, old sucks. Cheers Terry
@bryanpoole4749
2 жыл бұрын
I've got neuropathy in my feet and hands. As a mechanic I used to be able to reach in and do everything by"feel" now I drop everything and have trouble starting nuts on bolts
@machinist5828
2 жыл бұрын
@@bryanpoole4749 the frustration is real. I've been a machinist/welder/mechanic since I was 14. No regrets though. What a ride.
@davidp8157
2 жыл бұрын
@@bryanpoole4749 old age is a bugger, ( but better than the alternative) Old age before you are( old, that is) is plain unfair But Whoever thought life is fair hasn't seen much of life....
@SB-nr1dz
2 жыл бұрын
I like when you show the camera what you've taken off and where it was from. It's like I'm here to help remind you if you forget
@milwsdl39
2 жыл бұрын
Glad the old girls being kind to your Marty awesome job as always
@horstszibulski19
2 жыл бұрын
Amazing to see that you squeezed your hands, your eyesight, tools and even us via the camera into that tiny spot! Normally only one of these things would fit in there.... Thx a lot, great job! :-D
@cooperfarra5408
2 жыл бұрын
Nothing beats a good Marty t vid
@doodybird5766
2 жыл бұрын
Marty, you can fix anything. That's a priceless gift in today's throwaway and forget it world.
@randy5411
2 жыл бұрын
Marty the great fixer strikes again. I look forward to watching you fix that exhaust leak.
@SMGJohn
2 жыл бұрын
Kind of crazy how such a minor fault can cause such a huge problem. Just goes to show how amazing airplanes or space crafts are put together where a micro scoping problem could cause a crash.
@jefflormans5441
2 жыл бұрын
Planes basically built the same way but every part has a specified life and they're strictly maintained.
@blackbuttecruizr
2 жыл бұрын
Great save on this machine!
@johnhancock517
2 жыл бұрын
This is a man who has spent countless hours looking for dropped screws, nuts, bolts, etc. That's the only way he knew to put a rag under the pump.🤣 Love these videos!
@paulrivett2871
2 жыл бұрын
When everything is against you - sheared bolts, space to work in, gummed up allen heads... Positive fortitude makes it work and it (again) reminds me of my childhood when it was possible to rebuild a Nuffield tractor gearbox in a farmyard in the freezing cold with whatever tools could be found; not me of course, my Dad. Great work Marty, loved the vid.
@blastingweevil2968
2 жыл бұрын
nice when its an easy and cheap fix also when you dont have to dismantle half the machine to get to the fix a good day allround.
@87mini
2 жыл бұрын
You saved us the from seeing the frustration of getting that return spring back on the linkage and shaft! When I saw that and where it was, I thought "Now that'll be a bugger..." Glad to see it ship-shape in the end.
@MartyT
2 жыл бұрын
There may have been some swearing while installing said spring
@DiHandley
2 жыл бұрын
Very satisfying!
@richardorchard3364
2 жыл бұрын
Marty sure has patience and a steady pair of hands.
@carlosmontoya8658
2 жыл бұрын
Hello from Virginia, USA. We enjoy your content a whole bunch, sir!
@silentninjer1
2 жыл бұрын
Great work Marty, fiddly little job that too especially the return spring. Keep up the good work your videos are keeping me going after my hernia op 👍🏽👍🏽👍🏽👍🏽🙃
@mischef18
2 жыл бұрын
A doctor used an endoscope to check my age a few years ago, looked up my date. Nice fix bro and great video too. Safe travels
@PowerTom286
2 жыл бұрын
Difficult and crappy place for repair and maintenance, but you've done a very good job, Marty. Sincerely Tom
@regunter6599
2 жыл бұрын
The place where old machines go to be put back into service without a fortune spent on the repairs. There are a few people like you in lots of places but there are so many more who just give up on the old iron because the shiny new thing they are looking at works faster and has lots more features. If they have unlimited money, or a way to make enough using the shiny new thing, then what they leave behind is still useful, you prove that all the time. I love watching you make old iron live again.
@deborahwebb3598
2 жыл бұрын
Marty we love your videos and you have a wonderful family! My husband believes you could fix anything with a nut and bolt.
@billyhaddock5540
2 жыл бұрын
Congrats Marty on finding out the pump leaked. good job repairing it.
@terrytopliss9506
2 жыл бұрын
That was a fiddly job Marty,well done.👍👍
@davidcolesr.8628
2 жыл бұрын
Good Day Sir, From South Central Pennsylvania, USA
@leifhietala8074
2 жыл бұрын
Not gonna lie, that dozer sounds surprisingly good now, especially when you consider where you found it.
@evil17
2 жыл бұрын
Good job Marty! You are raising the bar on video entertainment, cheers
@born_again_torinos
2 жыл бұрын
Normally, me fixing something like that would stress me out greatly. But watching Marty do it relaxed me. Thanks Marty.
@jesusisGod1434
2 жыл бұрын
Hi Marty! At 3:56 it’s almost like you are my dentist gently digging out the last 6 months of impacted food from my molars! Those little mirrors they use could be handy for you. Okay now I’ll continue to watch you discover the problem and fix it with whatever you have laying about. 👍🏼
@jameskurdy4873
2 жыл бұрын
You continue to amaze me, thanks for having the foresight to allow us into your process
@davidshipulski4532
2 жыл бұрын
Great video! Its not a leak its just automatic frame rust preventative. The older machines seem to have it not the new ones lol.😂
@kennethbolton951
2 жыл бұрын
Frankly, I am amazed at your closeup camera work, very professional.
@robertordewald8678
2 жыл бұрын
Thanks for sharing Marty. You have such a quiet way about you, it's a pleasure to listen. I enjoy what you work on. When I was healthier this is what I loved to do as well. Hopefully I will be able to do something again in the near future. Thank you for sharing these videos with us it is a real pleasure to see a little bit into your life. Thanks again, Bob from Virginia USA
@irongoatrocky2343
6 ай бұрын
The Parts Swappers would have wanted to sell you a whole new pump! but sometimes its the simple things that need fixing!......a little bit of patience and thinking and it was done! way to go!
@mlg223
2 жыл бұрын
Great to see you making progress with it. I don't envy the trouble you'll have to face just getting it into a position where you can finally tension the tracks, but I wish you all the best with it 👍
@bellofbelmont
2 жыл бұрын
I see you left out all the swearing while trying to get that Allen screw and spring back on ... 🤣🤣😂😂 Jim Bell (Australia) Thanks for the vid.
@richl6827
2 жыл бұрын
I’m so curious about his background, training or education. He’s a master of whatever he attempts. Awesome videos!!
@brianmoore5498
2 жыл бұрын
i find it delightful to get a wink and a nod from a design engineer long gone that understood three dimensional thought and the significance of servicing a moving part with human hands. thank you
@petewebster2977
2 жыл бұрын
Marty T, you have the Hands of a Surgeon 👍 Pete Australia 🇦🇺
@NolanTyrrell
2 жыл бұрын
This and Cutting Edge Engineering are two of my favourite channels. They are massively different and simultaneously and the same. Thanks.
@morganobrien413
2 жыл бұрын
Well done Marty great investigation and a rubber gasket a couple of cents.
@deborahwebb3598
2 жыл бұрын
Good job Marty, you seems to always have the fix
@salsolo2403
2 жыл бұрын
this mans fettling skills are legendary :) well done Marty !
@wackowacko8931
2 жыл бұрын
You really didn't need to remove the Allen socket cap screw that was stripped out on the bottom of the pump, but they can usually be removed if you use a tight fitting Torx drive bit instead of an Allen wrench. Allen wrenches are wonderful at stripping out Allen socket headed cap screws, so instead of using them anymore, I use tight fitting metric and (USA) standard Torx bits as a replacement for the Allen wrench in almost all situations. It works a lot better than most people imagine.
@davidp8157
2 жыл бұрын
100% endorse this, covered with both metric and imperial sets is always a given
@MartyT
2 жыл бұрын
Good advice thanks.. luckily i didn't need to remove that stripped out bolt, I noticed the leak was coming from further up.
@jackrichards1863
2 жыл бұрын
Well done . Now it can slowly gather oil and soil like it should. (no diesle wash)
@64marine
6 ай бұрын
Check for auctions and folks w3ith tracks for that beasty; reliable user beats a source of worries any day. Good tracks are a must have.
@simperous4308
2 жыл бұрын
Yay!
@yamonda900
2 жыл бұрын
Damn fine work there Marty , you make great videos, I know how much work that there is to make these videos , well done.
@M21L35
2 жыл бұрын
Yet ANOTHER satisfied customer for a job well done! It's ALWAYS a veritable treat to see Mr. Wizard (Marty T) @ work once again!
@sheph7
2 жыл бұрын
not sure what is more amazing, got it apart, got it reassembled, didn't lose any parts, fixed problem... impressive.
@dannyinaus
2 жыл бұрын
I always find it amazing that it is usually the tiniest pieces that bring down the giant machines.
@hadynmcloughlin4661
2 жыл бұрын
Great job Marty look froward to seeing how the dozer goes as you bring it back to life. Your drive, knowledge and skills to keep the older machines running in such a 'throw away' world is a pleasure to watch. We need more people like you mate keep it up. (watching from Australia)
@andysaunders3708
Жыл бұрын
Given that you've obviously used the machine, I'd have thought that the combination of diesel fuel and heat from the engine would have prevented corrosion. I've un-seized old tractor engines by filling the cylinders with diesel, or even dunking the entire engine into a bath of diesel. It's not a quick process, but if you can try to bar it over every couple of weeks, it always seems to work. Kinda surprised that the throttle lever was held on with an Allen-headed fastener. Seems to me that the old girl wasn't designed like that? Great repair!
@dwhallon21
2 жыл бұрын
Marty, I have been following your videos for some time. You never cease to amaze me. Maybe it is because we are a lot alike salvaging what others give up on, but you my friend take it to a whole new level. Awesome video my friend
@AntiqueCarsandStuff
2 жыл бұрын
The modern world couldn't function without O rings. Good job.
@CapnJackSB
2 жыл бұрын
An Aircraft showed me a great trick for installing, or removing, "O" rings, or pins in a connector. Smear a bit of alcohol on them. It makes them slippery and easy to work with, then quickly evaporates.
@davidp8157
2 жыл бұрын
If alcohol makes them slippery, avoid that, it's slippery because it's dissolving/destroying the rubber. Use a smear if what ever it will be working in or actual rubber grease, for suitable o rings a light smear of oil or grease makes a huge difference
@joerodrigues3816
9 ай бұрын
My god you bloody know you’re stuff mate amazing work
@cdsparksart4440
2 жыл бұрын
You sir are an extremely lucky man to find and have simple fixes for all your equipment
@NigelMarston
2 жыл бұрын
Another brilliant o-ring fix. I am convinced o-rings should be included in every man's toolbox alongside WD40, duct tape and a hammer. All done without the trademark black gloves too..!!
@waynebrundidge206
2 жыл бұрын
Was pleased to see you could make the repair without removing the pump. 🌟😎
@josephlwallssr6166
2 жыл бұрын
Great, job, Marty! Thank you for giving us an update on this beautiful old, girl!😀👍
@michaelschuenemann3505
2 жыл бұрын
Fixed the Fuel Pump - Congrats and it was only two O-Rings ! Brilliant Job - we love Watching You Work ! Many Cheers from us in Australia - well done !!!!
@Green-Mountainboy
2 жыл бұрын
One of the only times i dont mind watching an endoscope being poked up from underneath 😂🤭
@VintageTexas59
2 жыл бұрын
Like a brain surgeon, steady fingers in tight spaces, don't drop any tools in the patient. Excellent work as usual Marty, engine sounds great. Cheers from Texas * * *
@kilmerartmamaril3002
2 жыл бұрын
Your amazing iron work skill sir
@topotone
2 жыл бұрын
Cool Marty. A mechanic’s hands that double as a surgeon 😊 Great fix, and no robotic assistance needed.
@markhensley9378
2 жыл бұрын
Great job Marty! You've got the patience of Job. Thanks again for your time today. Enjoy your weekend.
@jamesthompson8008
2 жыл бұрын
Great work man! Very methodical approach saved TONS of labor. As other comments allude to, most would taken the whole pump off. You did great work there - where I would've lost a couple screws to the belly pan. Cheers to all!
@Yutani_Crayven
2 жыл бұрын
Omg. It keeps getting progressively finicky. Mad props to you. Stuff like this takes the patience of a saint.
@dwaynekoblitz6032
2 жыл бұрын
The power of a little O-ring. Excellent find.
@johnkruton9708
2 жыл бұрын
Marty T: sledgehammered the top of this pump. I don’t know why…… Me: watching his deftness with fiddly bits… Get me my sledge a few good whacks never hurt.
@2secondslater
2 жыл бұрын
Fantastic field repair, mate. Great job!
@m.g5818
2 жыл бұрын
Grown to love your videos watching you get all this machinery working.👍⛏️🇦🇺😊🙋
@Chr.U.Cas1622
2 жыл бұрын
Dear Marty T. 👍👌👏 Extremely well done again and as always (video and work). This repair was a great success (only 2 tiny rubber o- rings were needed). Congrats! It definitely paid out that you searched for the leak meticulously before removing anything. So the effort was relatively small to fix it. I'm always astounded how well/strong the engine of this old workhorse sounds. As always: Thanks a lot for making teaching explaining recording editing uploading and sharing. Best regards luck and health to all of you.
@mongosaqqara
2 жыл бұрын
Marty MacGyver...another brilliant fix!
@rnappi
2 жыл бұрын
Nice and amazing job 👍 waiting for turbo install
@metricstormtrooper
2 жыл бұрын
Your up really late, it's 10pm here in Tasmania, you should be in bed.( Actually it's really nice to get a late night Marty t video)
@tylerr676
2 жыл бұрын
10:04pm here in Queensland
@andrewlindley4865
2 жыл бұрын
@@tylerr676 I don't think the midnight oil would ever pull Marty up
@nickw7619
2 жыл бұрын
I have a box of random size rubber seals just like that... super handy to have laying around. Don't need it every day but when I do I'm glad I have it. Cheers to another repair well done
@Mrlang74
2 жыл бұрын
Oh why do I find this so dam interesting, 6am sat morning coffee in bed watching a d9 fuel fix , best way to start a weekend , while wife is on tic toc something rotting her brain ,, feeling wise and manly now ,, keep it up ,, wife wants to see you fix a vacuum or blender , ,,, she’s gone now
@jesusisGod1434
2 жыл бұрын
This wife watches and tries to fix her own tractor, I introduced my husband to Marty, and now he shares his videos with the guys he works with.
@Jack-gy7cs
2 жыл бұрын
Very easy fix, just a very tight spot. Nice.
@screwsnutsandbolts
2 жыл бұрын
Excellent job 👍
@organiccold
2 жыл бұрын
Nice result Marty. Step by step it is becoming nicer and nicer
@tonyrinker9726
2 жыл бұрын
Felt like I was watching surgery. Marty does it again, good job mate!
@AndrewHCann
2 жыл бұрын
Excellent video Marty T :) glad simple parts tune up fuel pump and no more leaking we all hope next fix exhaust leaks also dozer need fix up on !
@johnwarwick4105
2 жыл бұрын
All those springs and clips what could have possibly gone wrong 🤣🤣. How on earth you work in those gloves I will never know. Well done interesting video
Пікірлер: 496