I have a 05 Tahoe z71 I just put a oil pump in and I didn’t have to remove the front differential i just lowered it Down without removing the axles just the nuts and bolts and let it hang without any damage and the pan was removed easily.
@mikebelcher6692
8 ай бұрын
Wish I would have read ur comments, I pulled diff 2x in 2 different trucks
@justinirby1762
6 ай бұрын
Same way I do it. 😂😂😂. Suck some folk don't pay attention to detail. Most of the time there is a easier way
@markmantooth7693
2 жыл бұрын
Great to know. Thank you!
@outfitsgarage88
Жыл бұрын
Very good information 👌 👍 👏
@rickn8or
6 ай бұрын
I had an '01 GMC that the oil pressure would drop to zero at idle when cold, fine after warmup. Turned out to be the two O-rings in the pan gasket that carry the oil from the block to the filter and return. They were cracked and passed oil from one to the other. Replaced O-ring and pan gasket, everything still fine when I sold the truck at 395K miles. Sort of immaterial, since you're going to replace the pan gasket anyway (right?), but it's still something to look for.
@paulkaufman4901
Жыл бұрын
I do appreciate the information you shared but, I wish you had shown more of your work.
@pauljanssen7594
6 ай бұрын
The Chevrolet LS oil pumps won't like to pump dirty oil it causes excessive wear on the aluminum housing of the pump, I had to change the oil pumps on a fleet of buses I was working on due to lack of oil changes. I used to high volume low pressure m55 oil pumps I don't have to drop the oil pan tricky getting a bolt in for the pickup.
@ozziecollett3088
2 жыл бұрын
Excellent job, had a similar problem with low oil pressure, needed to do pump and O ring to👍
@doddgarger6806
Жыл бұрын
I put one in a 12 yukon 6.2 and it has way more oil pressure than it did with the 295 pump
@jonperley7304
Жыл бұрын
Question for you can one check the pump pressure at the primer port???
@cromaticdragon5079
Жыл бұрын
Has this same problem on my 2008 H2 Hummer
@Airman..
2 жыл бұрын
Good job
@stuartarneaud218
Жыл бұрын
Nice work
@richarddiaz3275
Жыл бұрын
How much would a job like this go for ?? Low oil pressure on my 6.2 camaro
@dannmann17
Жыл бұрын
I’ve done those with the oil pan in place, it sucks, but it is possible👍🏻🇺🇸
@mikebyrnes8493
5 ай бұрын
I’m having the EXACT same issue.. did this resolve the tick you were hearing also?
@rollinmetzger7392
7 ай бұрын
Did this repair correct the lifter ticks?
@jonnygarbarino3285
Жыл бұрын
Will this pump work on a 2008 suburban 5.3 about to do this job myself did the oring still low oil pressure might as well do pump now
@joebaucom4537
4 ай бұрын
Great !
@909ARSENAL
Жыл бұрын
Change the oil pressure release valve
@thomasbailey9820
Жыл бұрын
I went to the link and Amazon says m355 does not fit 2008 Tahoe. M295 is what it’s shows? What’s the difference?
@nsgtr753
26 күн бұрын
Link to the puller you used?
@aggplbg0664
6 ай бұрын
Have a 6.0 LQ4 , noticed low oil pressure coming on slow, went from 60 40 20 then went to 10 then 5 . Change oring , same , then changed pump went with 295HV standard psi. Definitely have a cam bearing issue. Fire's up to 20 ,then drops to 10 idke , when i accelerate goes up to about 30, never gets any higher, freeway drive stays at 30 then as you slow down to a complete stop goes badk down to 10 . No issues so far runs like a top, milage is about 165000.
@weaversstonehousefarm
5 ай бұрын
Same problem with mine. Used the same pump. And has the same problem. Did you change the cam, lifters, cam bearings out?
@aggplbg0664
5 ай бұрын
@@weaversstonehousefarm I decided not to tear into the motor! You going to see how long it lasts! I've been driving on it for about a year now I worked on it in the beginning of January February of 23 year!
@weaversstonehousefarm
5 ай бұрын
@@aggplbg0664 thank you
@jryoung5460
Күн бұрын
@@aggplbg0664 is it still going? Has it got any worse?
@aggplbg0664
Күн бұрын
@@jryoung5460 still running! 🤞
@20tea
3 ай бұрын
Melling 10355HV- high volume will increase the hot idle psi by about 5psi and the pressure springs could increase running pressure past 40 psi till the relief valve in the pan opens up. Highly recommend the hv pumps for higher mileage motors. If plugging up the releif valve with a m14x1.50 oil plug, use a standard pressure spring to not over pressure the system when running at hwy speed as it will trigger a code for high pressure. Generally the cam bearings open up more through wear reducing oil pressure. Replacing the o ring helps and clean the oil pressure sensor screen if applicable too. Fyi, the new cam bearings in the market are slightly wider for better support of the cam at .775". Replace cam bearings with updated parts.
@jeremyjones8872
2 ай бұрын
Man ive got soo many questions,.i have put about $1500 into my 07silverado 5.3 and have had 2dif mechanics fuck me over and still NO PRESSURE so i m doing it myself and have everything out but need a good guy to explain afew things
@20tea
2 ай бұрын
@@jeremyjones8872You have DOD lifters BTW. What happened?
@jeremyjones8872
2 ай бұрын
@@20tea sorry i dk what that even means? I started with sensor then pickup oring then pump,and now was told no pressure because it wasnt primed but now im out of $$ for another shop so tryng to figure out on my own and its over my head
@jeremyjones8872
2 ай бұрын
@@20tea how do i know about dod lifters?
@20tea
2 ай бұрын
@@jeremyjones8872 So what symptoms caused you to initially send the truck in for repairs? No oil pressure or low oil pressure? Did the mechanic 'repair' something and now no oil pressure?
@user-rt5tv9cy5c
7 ай бұрын
Did the lifter tapping go away ???
@alexanderdrywall3043
Жыл бұрын
So the m295 is the better one you want.
@MAD_BST
Жыл бұрын
GG man.
@jeremyjones8872
2 ай бұрын
Anyone if he had to remove anything with the powersteering pump or lines?? Ive got a 07silverado and the lines are in my way to get to that allen bolt to prime the oil pump
@aaronzavala4336
3 ай бұрын
I had a question is my 5.3 supposed to be running a bit rough or need break it has new lifters and it’s still ticking but I haven’t drove it far cus I was testing the truck out still but it has like 20 oil pressure and just slowly drops as it warms up it has new crank shaft new piston bearings crank shaft bearings new oil pump and it still running like ass 😢 I had a question is my 5.3 supposed to be running a bit rough or need break it has new lifters and it’s still ticking but I haven’t drove it far cus I was testing the truck out still but it has like 20 oil pressure and just slowly drops as it warms up it has new crank shaft new piston bearings crank shaft bearings new oil pump and it still running like ass 😢
@fofodiy
5 ай бұрын
What causes high oil pressure when cold in the 60psi. Then when hot goes down to 30-40psi. But when revved goes up to 80..
@justinlalko7834
Ай бұрын
Just oil bring cold then hot it thins out. Its normal
@user-xf7ce3ie4n
8 ай бұрын
I have a 2007 Tahoe 5.3 engine. The valve lifter for one room got stucked I replaced it and all was fine. I drove the car for some time and that same room the valve lifter got stock again but before that I noticed low oil pressure. Immediately I noticed the low oil pressure I pulled over the car check to see if there was a physical abnormality of which it was not. Drove the car for about 5 miles the the low oil pressure signal came again. Please what could be the possible cause of this valve lifter being stock?
@mikebelcher6692
7 ай бұрын
The oring can harden and loose seal between pump housing and pick up tube; it also is rumored to have been pinched/damaged upon install. I had a 2005 6.0 oring had hardened; Son had 2006 5.3 oring was split in 2 different places. Put melling hi psi pump in 5.3/melling hi vol-hi psi pump in 6.0 and replaced both orings The lifter was ticking in 2006 but this fixed the issue
@Popseygtrx7
5 ай бұрын
How much does it cost to
@KJ-ep9cw
Жыл бұрын
What code did you have P0011?
@ryanbuck3789
9 ай бұрын
Have you heard of the oil pump, making a knocking noise or almost sounding like a lifter noise, And it Sometimes comes and goes? I have a 06 Silverado 2500HD w/t with the 6.0 The truck never had an issue until I did a oil change and put the Lucas high mileage engine oil stabilizer in it the very next I went out and started it to let it warm up before work and I heard it from inside the house it was sounding like the lifters were just hammering and it had like no oil pressure so I flushed that oil out multiple times but it never fix the problem. It’s been years now and that tick is still there from underneath the hood it sounds like it’s the injectors but I doubt i because the oil pressure is low and goes up to maybe 3040 when you’re hard on the gas. It’s still runs just fine. Smooth as ever but the tick drive me insane sounds like my motors going to blow. I did the O-ring twice it’s good that’s not a problem I just don’t see how that could happen overnight but then again, we are things have happened. A local fleet mechanic is telling me it’s the oil pump making all the noise and he changes them out like a few a month on their fleet. It’s just weird when you’re getting on the gas it almost sounds like a cat go through a 64 impala with round, cut exhaust tips and straight pipes.
@aaronzavala4336
3 ай бұрын
I had a question is my 5.3 supposed to be running a bit rough or need break it has new lifters and it’s still ticking but I haven’t drove it far cus I was testing the truck out still but it has like 20 oil pressure and just slowly drops as it warms up it has new crank shaft new piston bearings crank shaft bearings new oil pump and it still running like ass 😢 I had a question is my 5.3 supposed to be running a bit rough or need break it has new lifters and it’s still ticking but I haven’t drove it far cus I was testing the truck out still but it has like 20 oil pressure and just slowly drops as it warms up it has new crank shaft new piston bearings crank shaft bearings new oil pump and it still running like ass 😢
@ryanbuck3789
3 ай бұрын
@@aaronzavala4336 sounds to me like something isn’t right in it with all new bearings like that. You should have a lot of pressure I would think it should have around 40 to 50 psi when it’s running and warmed up when it’s cold we just built a 6 L and put a high oil pressure pump in it and it had 120 psi we had to take it back out if it’s new lifter, it shouldn’t be making any noise. Somethings going on with it.
@aaronzavala4336
3 ай бұрын
@@ryanbuck3789 yeah ima take off the oil pan and see wassup I’m pretty sure I did everything right but I could’ve made a mistake but I’m thinking about trying motor flush if everything checks out good in the motor try it then add more oil I’m saying this because my last crank spun a couple piston rod bearings so I swapped it new crankshaft new bearings and the liftersI’m thinking all the metal shavings are messing with it getting stuck in the valleys or idk
@aaronzavala4336
3 ай бұрын
@@ryanbuck3789 when I had it out I should’ve got a compressor and blow everything out but ima try motor flush I heard that helps with the oil pressure and it fixes the ticking it has oil pressure it just drops as the truck warms up
@aaronzavala4336
3 ай бұрын
@@ryanbuck3789 unless it’s my exhaust manifold it has only four bolts holding them on each side the rest broke in the block you think it’s a leak I heard that sounds like a tic when I rev it sounds like air is coming out from the sides of the heads like it’s escaping out the sides where it’s not seated right ?
@aggplbg0664
6 ай бұрын
295HV standard pressure 😊
@haynldy
3 ай бұрын
What year is this?
@Popseygtrx7
5 ай бұрын
How much it cost
@jorgemarquez7637
Жыл бұрын
What was your oil psi when the engine was hot? I did the same thing to mine and went up to 60 cold and once it reached operating temp dropped down to about 10psi
@meldog88gaming
Жыл бұрын
Mines did the same thing,hope he answer!
@marcusware712
Жыл бұрын
Cam bearings
@Papisartee
9 ай бұрын
Was it your cam bearings after all ?
@RickMandanga-cm6ph
9 ай бұрын
Any update
@motopsycho6169
8 ай бұрын
dude mine did the same thing as well with a 10255 but with a stock pump i was at 25+psi hot idle
@eddievazquez2330
9 ай бұрын
Hey bro I got 80 psi on my dash then low oil pressure displays every so often I've changed the pick up tube o ring and pan gasket torqued correctly swapped oil sending unit but periodically low oil pressure warning lights up ,any idea what it could be
@cleivycruz5543
4 ай бұрын
You may delete Oil pressure relief valve ???
@eddievazquez2330
4 ай бұрын
@@cleivycruz5543 where is the location of that part
@Dave_Bee
Жыл бұрын
So was it the pump that failed or just the oring you think ?
@boydco6587
Жыл бұрын
Did you watch the video?
@bobgyetvai9444
5 ай бұрын
You made a big deal with that pump . Totally unnessasary hyper in the diaper .
@slowrook
2 жыл бұрын
why M355 and not 10355HV or 10355? coz iam about to change my oil pump in my tbss and am really confused :\
@FadetoBlack1463
Жыл бұрын
10355HV is an ever higher volume over the M355 and the 10355. About 42-45% more than stock. It has even thicker pump rotors than the M355 and 10355, which are about 33% over stock.
@techo61
Жыл бұрын
OH NO NO NO. Do not for a second believe the pump 'self centres' by rotating the crank, the outer rotor floats and the crankshaft does nothing to centre it inside the housing. Using this method will most likely end up with another pump failure due to the gears not being centred and a lack of lubrication all the way around the outer rotor and its aluminium housing. The only way to centre these and the OEM Internal Gear Pumps with their oversized mounting holes (no locating dowels) is the remove the cover and use shims on opposing sides of the outer rotor. kzitem.info/news/bejne/pI15r5iegGJlf44 Otherwise a good video, cheers.
@warriorplutotrent3827
7 ай бұрын
Lol old information. That may be true for those big name brand overly expensive pumps, but melling is just like you said. Just rotate the crank. Melling will tell you the same thing.
@dumbotater2158
Жыл бұрын
Why did you skip the installation process?
@shannanmichael2009
Жыл бұрын
My vehicle was hit in the back, after a month at the shop, the owner called and said it was finished but low on oil.. I told him, he could add the oil.. Went to pick up, oil light came on, with low oil pressure stop engine now.. After checking the oil, I noticed they put 2 quarts over the needed oil.. I had them drain the extra oil.. We've changed the oil pressure sensor and screen thingy, but still having problems.. I have no engine light on, once started I have 40 pounds of pressure, after about 30 secs , I receive a chime sound, oil light on, low oil pressure reading, and drops to 0 pounds.. Any tips would be greatly appreciated,
@austinwest6736
Жыл бұрын
Oil pressure relief valve prob. I’m assuming this is prominent on idle and goes away in drive?
@mikebelcher6692
10 ай бұрын
I’ve had 2 trucks with same prob. GM sometimes cut/pinched the oring on original install I read. 1st one 5.3 o ring was split;installed standard melling in it-psi went to 45 n lifter stopped ticking. 2nd one 6.0, o ring was not sealing. Installed melling M355 in it psi went to 40 @ speed 10 at idle. Truck was neglected when I bought it, suspect worn brgs.
@user-xf7ce3ie4n
8 ай бұрын
@@mikebelcher6692hey bro. It's like am having same problem with my 5.3 Tahoe engine. Valve lifter for a particular room keep sticking. The second time before it got stock I received a signal low engine oil pressure. What do you think can be the cause? And what do you advise me to do?
Пікірлер: 82