I love your ingenuity to make your fixes and upgrades on a budget that we can all relate to. Well done Andris. I think this project deserves a “Super Mom” seal of approval.
@Ants_Pants
9 ай бұрын
hehe yeah
@Melicoy
9 ай бұрын
@@Ants_Pants Weld teeth And 15:27 this dirty stuff turns people off subscribing.
@BCGray10x
9 ай бұрын
Thanks! I can not tell you how many people have told me that you truly bring back REALITY
@Ants_Pants
9 ай бұрын
haha :D thanks a bunch
@2hacksinashack
9 ай бұрын
Good job! At 2:06:20 To remove tools from the tail stock, crank the handle to retract it fully. It will push the tool out for you. They are a friction fit with the taper. And the flat on the end is to keep the drill chuck or the taper adapters from spinning in the tail stock.
@13tucker45
9 ай бұрын
Beat me to it
@Ants_Pants
9 ай бұрын
yeah i figured it out a bit later :D
@gordonagent7037
9 ай бұрын
Andris, that lever according to JapanMachineryParts is the control for the PTO. I’m pretty sure you’ll find that thread on that nipple is NPT,it’s tapered so that as you tighten it, it will seal itself, no thread tape required to prevent tape getting into the system and blocking control ports. I really appreciate a man who looks after his machinery and you do that very well mate, the new paint job was the icing on the cake. Another splendid video Andris, heaps of content, wit and the commentary was great, as always. Take care mate
@Ants_Pants
9 ай бұрын
Cheers
@francisremillard9482
9 ай бұрын
America loves you & all your family.. Thank you for just being you....
@Ants_Pants
9 ай бұрын
thanks Francis
@jcyran
9 ай бұрын
I don't know what he is doing but his videos hold my interest. I guess I'm here for the paint and stickers, and of course the charm of Andris. 😊
@BCGray10x
9 ай бұрын
Love you, Bro. Your humour, your Family, your Values. You give us something that most have lost since the 1960s; it is called living and life; thank you so much for including your "Super Mom, and cute nieces". From an equally crazy Canadian, though just a little older
@Ants_Pants
9 ай бұрын
Thank you so very much
@kalpanathapa6713
7 ай бұрын
Tuci6b@@Ants_Pants
@guy7gsa
9 ай бұрын
Found your channel only last week thank youtube algorithm not. Enjoying your videos, your funny, don't pretend to know everything and keen to learn. Loving the dry sense of humor. Keep it up.
@Ants_Pants
9 ай бұрын
got it boss👍
@robertmatthews4285
9 ай бұрын
Someone may have already said this, but that rotary valve under the left side of the seat with all the hydraulic lines changes the control pattern. Most likely between ISO and SAE patterns. Different patterns change what functions control lever movements activate.
@The-Deadbolt-Deputy
9 ай бұрын
Thank you
@Sokrates66
9 ай бұрын
I believe tat steel is Hardox. The left lever at the back is the PTO selector lever. The pedal to the left is a 2 speed pedal. The lower lever under left consol could be to widening the tracks if its equiped with that option.
@Ants_Pants
9 ай бұрын
it's not, but there is a hydraulic pin that comes out from under the machine to lock swing. Might be that
@Ants_Pants
9 ай бұрын
what do you mean about the PTO selector?
@Sokrates66
9 ай бұрын
Im guessing changing the flow rate. @@Ants_Pants
@pjotrkuh
9 ай бұрын
I also think it's the swivel lock lever...
@deborahfaulk5532
9 ай бұрын
Andris, how in the world do you make working on a Yanmar look interesting?! 2 1/2 hours of you doing your repairs was a real bonus! Do that anytime you want to. Have a great weekend, take care
@deborahfaulk5532
9 ай бұрын
The paint job looks great, the sky blue is so cute!
@Ants_Pants
9 ай бұрын
idk bro, magic
@Ants_Pants
9 ай бұрын
i think so too
@deborahfaulk5532
9 ай бұрын
@@Ants_Pantsthat is so true!
@johnferris2919
9 ай бұрын
Regarding the roller zerks, I would weld a 1 to 1.5 inch open pipe around the zerks. They will get jammed with dirt but will be protected from grinding them off. When it is time to grease the rollers just pull out the pressure washer to clean the zerks off.
@jeremy2058
9 ай бұрын
Thank you for sheering this project, the time just flow 🤙
@Ants_Pants
9 ай бұрын
thanks
@sl5303
9 ай бұрын
hello the big valve on the left with several hydraulic pipes is for inferring the controls from left to right and vice versa and the lever on the left like a parking brake is a brake for the swing
@Ants_Pants
9 ай бұрын
🎉👍
@thebear5454
9 ай бұрын
It's the highlight of my week when I can watch one of your DIY projects. Always an adventure in cobulation. 👍👍
@Ants_Pants
9 ай бұрын
hehe
@grumpycat_1
9 ай бұрын
The new fitting is likely a NPT (National Pipe Tapered) fitting or a BSPT (British Standard Pipe Tapered) or vise versa. But if the old male to male fitting is Parallel its likely an "Inverted Flare" fitting of some type. It could be JIS ( Japanese Industrial Standard) "30° Male Inverted Seat" which are interchangeable with BSPP (British Standard Pipe Paralell) connections. There seems to be a concave bevel on the face of the male fitting on the ID. If you look into the female fitting on the boom and there looks like a convex seat or like the tubing/ferrule end on a compression fitting (the nut side) its likely an inverted flare or BSPP/JIS Female. If that IS NOT the case then I would say it might be a JIS Tapered/BSP Tapered thread. It could also be "NPSM (National Pipe Straight Mechanical) " which would explain the 30° seat and straight threads on the old male fitting, and the fact that the new fitting will thread on but won't go in "all the way" and wont seal. But i doubt this. Both NPT and BSPT fittings seal on the threads (with use of pipe sealant) and are dimensionaly similar but not interchangeable., they have the same thread size but differnt pitches, they will thread together but not seal. Which would explain the leak you had... (This could also be lack of thread sealant) NPT (National Pipe Tapered) fittings will thread into BSPP and BSPT (and JIS T and JIS Inverted Seat) Fittings but wont seal properly, (even with pipe sealant). BSPT Fittings will thread into BSPP fitting and will seal with the aid of pipe sealant. Since its a Japanese machine the old male fitting MIGHT be a "JIS tapered" (aka BSPT) and the boom side female then is likely JIS Female Tapered (aka BSPT, aka British Standard Pipe Tapered) or a BSPP Female which will seal on the threads To a BSPT male without a gasket or oring (but with thread sealant) If the boom side is a BSPP female and the male fitting WAS a "BSPP Oring" (since your said the old male appeared parallel) and that oring has perished/been lost, but these are usually only present on swivel fittings .. if any of this was the case though it would likely leak, unless a LOT torque and pipe sealant/old paint (visible on the old fitting) somehow molded themselves enough to seal. But as i said if the old fittings male threads are parallel and there is no place for an oring, and the female fitting looks to be a CONVEX cone in it my guess would be be some sort of inverted flare fitting or more likely a JIS ( Japanese Industrial Standard) "30° Male Inverted Seat" or BSPP both of which has parallel thread connections and a fundamentally interchangeable.
@audiquattro6768
9 ай бұрын
Likely JIC since it’s made in Japan.
@bradcrossman5068
9 ай бұрын
Well said!
@Ants_Pants
9 ай бұрын
yup
@grumpycat_1
9 ай бұрын
@@audiquattro6768 Do that make JIC inverted flare?, The expected end of a JIC would be a male fitting with a CONVEX sealing surface.. where as both side are concave on this fitting. My guess is its an inverted flare type fitting (convex sealing surface on the female side), more specifically and most likely a "JIS 30° Inverted Seat" AKA BSPP.
@philhermetic
9 ай бұрын
I like the long videos, from start to finish is much better than 1 short episode a week! Phil UK
@Ants_Pants
9 ай бұрын
Good to know!
@SuperHaptics
9 ай бұрын
Haven't even started watching but i give the thumbs up 😂. Friday night with 2 and a half hours of mad DIY stuff from Andris what more can you want 😂
@redsable6119
9 ай бұрын
There are several tubers I give the thumbs up upon starting the video, to make sure I don't forget, Andris is one of them.
@Ants_Pants
9 ай бұрын
thanks dude
@Ants_Pants
9 ай бұрын
👌❤
@bradcrossman5068
9 ай бұрын
Holy Heck! Two and a half hours! I gotta start planning my Fridays around these.🤓 Cheeeeers Lad!
@Ants_Pants
9 ай бұрын
haha
@egalegal1666
9 ай бұрын
2:24 As always, Andris has made every effort to present us with the best and most authentic sound effects 🤣👌 two and a half hours of the finest content 😘
@Ants_Pants
9 ай бұрын
always 👌
@GlobalistJuice
9 ай бұрын
Good video, even though I have zero interest in this machine, your video had me interested in the process of repairs for the full 2.5hrs!👍
@Ants_Pants
9 ай бұрын
hehe, glad i could be in service
@jonasbartels1716
9 ай бұрын
For the roller to protect the grease fittings: I would use the same pipe, but shorter pieces, maximum 1-3mm longer than the fitting, maybe even flush with the tip of the fitting. Less room for dirt, and due to less stickout smaller risk of getting ripped of, since you get less force on the shorter pieces. Leaving them blank could result in loosing them much faster.
@noahingram8052
9 ай бұрын
Great job and that fitting is tapered pipe thread and use thread tape as sealant, cut off a small piece of threaded black iron pipe and use a screw on pipe plug to cover those grease fittings just put antisieze on the threads
@Ants_Pants
9 ай бұрын
hmm ok
@johnhenderson3646
9 ай бұрын
For your track roller pin zerk fitting problem, could you weld a round pipe, similar to what you had. Just thread on some pipe caps on the ends. When it's time to lube them, unscrew the cap, service, and screw the cap back on.
@petermamo560
9 ай бұрын
Hi Andris. Your personality and your whole being is an absolute credit to you, you look at every job logically a fix it accordingly. And you mange to do it all by yourself, I love watching you work. It gives me hope, I retired many years ago. Now I can’t physically do much, but seeing how you work is a great tonic. I thank you from the bottom of my heart. Never stop doing what you do, you’re more than just a video. The Yanmar looked fantastic after the paint job and the stickers. She looks brand new. Keep up the good work ✅
@Ants_Pants
9 ай бұрын
Thanks sir 😇
@rowlandcrew
9 ай бұрын
there may be hardened teeth that slip and lock onto those bucket tooth stubs (common approach), the tapered thread is pipe thread (use teflon seal to wrap the thread), 4.5 mm drill bit is 3/16" diameter (freedom units), you can try to make a triangle bracket to move the top of the thumb cylinder out and back and use the cool new lathe to make bushings to tighten up the thumb joints, and back the tailstock on the lathe inside all the way then a pin inside will eject the morse taper tooling. so many options, so little time.
@billquantrill4960
9 ай бұрын
Thumbs up for muh "freedom units." Ah what once was.
@mavision6525
9 ай бұрын
As usual you're able to get things done. Great video.
@Ants_Pants
9 ай бұрын
Thanks 👍
@johnferris2919
9 ай бұрын
N9ce job on the Yanmar, I just looked at video when you first got it. Great job bringing her back to life.
@Ants_Pants
9 ай бұрын
well deserved
@sahinkaran
9 ай бұрын
Yine shirli dokunuşlar yaptın.İnan bana, Camarata senin kadar becerikli değil.Hemen yenisini söylüyor ve geliyor... Sen ise yaratıyorsun ve yaşatıyorsun.
@sanderd17
9 ай бұрын
2:11:40 some materials also work-harden when you go too slow. Going slow causes less chips to take the heat away, and a material can harder itself that way. Going for bigger chips keeps the material colder.
@Ants_Pants
9 ай бұрын
Ohh thats a useful tip
@Dirtlife98
9 ай бұрын
New teeth for that bucket will make a world of difference, and they shouldn't be too expensive. Definitely worth the $ in my opinion.
@rbhe357
9 ай бұрын
I'm not sure I'd bother with the bolts tho. Just weld new teeth right to the bucket. Most are anyway.
@Dirtlife98
9 ай бұрын
@@rbhe357 agreed, or take a chunk of dozer cutting edge and weld that on
@kirk467
9 ай бұрын
@@rbhe357I agree with that, new teeth welded on would work!
@christoff4735
9 ай бұрын
What that guy said.
@explodingtoast9898
9 ай бұрын
I think you mean £
@prinzeugenvansovoyen732
9 ай бұрын
1:29 you can buy a piece of seamless pipe, turn the outside to bucket, inside to pin, hammer them in place and weld them in place
@Ants_Pants
9 ай бұрын
hmm could work yeah
@jdkerk
9 ай бұрын
I don't know why I love to watch your videos. Maybe I have my father's mechanic genes. I really enjoy watching you figure things out. You definitely have a wealth of knowlege about almost everything!
@Ants_Pants
9 ай бұрын
Sounds like a solid reaaon 👍
@francisremillard9482
9 ай бұрын
That lever by the seat is for the ejection seat. One time use..
@Ants_Pants
9 ай бұрын
HAHA :D the parts catalog says it's "PTO CONTROL" what ever that means :D
@manifold1476
9 ай бұрын
1:40:30 A short piece of pipe cut open - shaped like the letter U and welded on with the open end down would protect the grease fitting and allow easy cleanout.
@PilgrimLad
9 ай бұрын
Black pipe threads start out narrow and they get wider, this helps them seal.
@dennisflemming826
9 ай бұрын
Most lathes have an extractor in the tailstoc wind all the way back , then give the hand a cople of quick snaps back by hand against the screw limit , if the part in the taper has a tang it will pop out . If out wind fourd and expose the hole in the side of the shaft, you then need a tapered wedge to remove the drill or centre
@Ants_Pants
9 ай бұрын
yup i sorted that one out a bit later :D
@Crawlerlane
9 ай бұрын
That is a national pipe tread "NPT" fitting it's tapered so it gets tighter as it's tightened . Can be used with pipe dope or teflon tape 👍
@jfjjjjfj
9 ай бұрын
It may be a BSPT (brittish standard pipe tapered). Both NPT and BSPT needs some sort of sealant. NPTF (fuel) is drysealing. NPT has 60 degrees and BSP has 55 degrees.
@Biffo1262
8 ай бұрын
Tapered male threads (NPTT) should not be used on parallel female threads. Tapered threads are usually for air not hydraulic. Parallel threads (BSPT) usually have a thread sealant or Dowty compound washer). I use 3M liquid hydraulic sealant.
@bjornflood6204
9 ай бұрын
I just clicked on the video without looking at the length. Its now 03:31 am in the Faroe Islands 🙂Fantastic stuff, I wish I had your energy. I have a small workshop in the basement of our house. I have some basic tools for mainly woodworking. So I´m down there pretending to be Antspants. You motivate me to try to do more, being more productive.
@Ants_Pants
9 ай бұрын
Wish i had more time to focus on woodworking :( Maybe one day hehe
@chrisoakey9841
9 ай бұрын
If you bend some 6mm polycarbonate sheet to wrap around the roof, it should add enough strength to make the roof roll over protection as well. Just bolt in in the outside of the metal bars to stop the roof folding sideways.
@Quake81270
9 ай бұрын
Place the hand drill on the left side of your body so as it wants to spin the whole drill to the right your body is up against the drill and helping keep it from spinning out of your hands. Be careful because it can still spin out of control.
@tkilg7169
9 ай бұрын
I think that the thing with many hydraulic lines is to change the pattern of control usage. Since you are accustomed to the controls as they are now, to change it would be unnecessary.
@allanwinter4991
9 ай бұрын
I agree.
@opengchris18
9 ай бұрын
2" reciever hitch on the back of the bucket for moving trailers is what i believe you discarded on the bigger bucket and asked about
@kirk467
9 ай бұрын
New wear flat bars on the bottom outside of the bucket would help from extra wear also!
@tujuprojects
9 ай бұрын
I would have changed color from that soviet blue to dark boom where greese don’t stick out so well. And the upper carrier to some yellow or orange. Under carrier is usually covered with dirt and mud, so dark color works there as well.
@Ants_Pants
9 ай бұрын
101 shades of pink
@18183
9 ай бұрын
That fitting has a tapered side and a parallel thread side. Gaskets or copper washers are to be installed only with parallel thread. On tapered threads (or fittings) the thread has to seal as it continues to expand as it goes in. The only thing that you can do to the fitting is a hydraulic sealant, which looks like a thread lock or a thread sealant. In case of sealing high pressure water use thread tape on tapered fittings. It is also common to use hemp threads (which look like blond ugly hair) mainly on high pressure diesel or high pressure steam
@18183
9 ай бұрын
And I forgot to mention that I don't like to use tapered thread metal to metal especially if it is a used fitting. So if it leaks definitely get a hydraulic sealant. Should cost around 12 euro for a small bottle and will serve you for a lot of fittings since you only use 2 or 3 drops per fitting
@Chris5685
9 ай бұрын
I second this, my air compressor has these tapered connectors, and they were leaking. Teflon taped them, fixed the air leak.
@Ants_Pants
9 ай бұрын
got it boss
@charlietoews1593
9 ай бұрын
Absolutely enjoyed this video. Thanks for your hard work. Awesome.
@Ants_Pants
9 ай бұрын
Glad you enjoyed it!
@kirk467
9 ай бұрын
Fabrication work my friend, cool Andris! I always enjoy watching you repairing your equipment and love your new modifications and additions in your workshop! I think your table will hold anything my friend!
@Ants_Pants
9 ай бұрын
can't park Joseph on it though
@ronniehoiting1588
9 ай бұрын
Thanks for the great video Mr Pants 😃 Your videos can never be too long in my opinion.
@Ants_Pants
9 ай бұрын
Glad you like them!
@ridebadger
9 ай бұрын
New teeth will make digging much easier, especially in rocky soil. Thanks for the vids.
@Ants_Pants
9 ай бұрын
Very true!
@tujuprojects
9 ай бұрын
Your mystery lever could change the drive motor - not gear - but swash-plate angle and make it go faster.
@Ants_Pants
9 ай бұрын
some shady parts catalog says its "PTO CONTROL", but that's all. Not much to go on.
@elaineb4806
9 ай бұрын
Thanks Ants for a great two and a half hour of entertainment 👍 your Yanmar looks super chic, love the black panels with the dark and light blue - the only suggestion I would make it to use more of the dark blue. For the grease fittings I would go for your idea of the thick angled metal below the fittings. Your work on the cylinder was amazing, great to see you experimenting with the lathe. Best wishes to you and your family 🌿🌿🌿
@Ants_Pants
9 ай бұрын
Thank you very much :)
@KentDiego
9 ай бұрын
Tapered pipe thread requires Teflon thread tape and often a sealer to prevent leaks. The paint job looks great.
@TheHomePros6221
9 ай бұрын
Never use Teflon tape on hydraulics
@Ants_Pants
9 ай бұрын
lol this topic is so weird, it's like 50/50, quick google says its okey
@TheHomePros6221
9 ай бұрын
@@Ants_Pants the reason why is cause hydraulics have very small ports and if a little peice gets in the system it will cause issues, instead use a hydraulic thread sealant
@madmodders
9 ай бұрын
The signal horns are a set of two (mirrored) with different frequencies because you're supposed to have them both mounted under the hood, sounding at the same time.
@Ants_Pants
9 ай бұрын
hmm ok
@madmodders
9 ай бұрын
@@Ants_Pants Of course you don’t have to. 😄 But a two-tone honk sounds bigger and louder.
@carloskawasaki656
9 ай бұрын
Thank you once again for this beautiful moment and everything you do, really fun and very interesting, thank again for sharing, have a nice week end 👍👍👍👍
@Ants_Pants
9 ай бұрын
Thank you
@mikestarkey7989
9 ай бұрын
New teeth for the bucket is definitely better, also the damaged/old teeth could damage the bucket itself and that's a lot more of an expensive , complicated repair!
@125sm3
9 ай бұрын
Fantastic transformation .
@michaelfelixb1316
9 ай бұрын
Wau , das Ding ist ja wie Neu 👌 was Du alles machst ist schon der Wahnsinn. Mein Respekt 👏👏👏
@Ants_Pants
9 ай бұрын
❤👍
@SuperMAZ007
9 ай бұрын
That was a lot of work. Still not the worst mini excavator I have seen. Found useful tips I can use myself, thanks man.
@Ants_Pants
9 ай бұрын
Glad I could help
@robertzapatka1082
9 ай бұрын
That lever may change the pattern for the controls, so you assign different control patterns. Wow she looks almost new!
@sammyshort3369
9 ай бұрын
@ Andrew camarata did a breakdown of his yanmar a few years ago he explains the pedal and levera I think
@Ants_Pants
9 ай бұрын
yup, pattern changer, no need to touch it.
@francispalmer9737
9 ай бұрын
Nice colour combo bro, you could probably see this mini excavator from space now. Cheers Ants Pants for 2.5 hours of juicy content.
@Ants_Pants
9 ай бұрын
Thanks 👍
@giggitygiggitygoofg6069
9 ай бұрын
Just wanted to make a suggestion. Buy yourself or build the crimper for crimping the hydraulic pipes, you can get them to fit on your hydraulic press. When you have a pipe bust the pipe work is normally fairly cheap its the hydraulic fittings that coost alot. I did this years ago and have save tons of money. Take your old pipe cut off the fitting and as long as they were not wot was leaking and knackered you either put them in the lathe and remove the crimped part which is literally just a piece of tube, once thats removed all thats left is a barbed fitting , you then weld on a new piece of tube which needs to be the same internal measurement so you won't have problems sliding the new rubber tube back on then re-crimp your fitting and boom done. Obviously between cutting the old crimp off clean up the overal fitting with a wire brush. My crimper cost me £165 which was 5 years ago and it paid for itself affter replacing 3 pipes as you can also use old pipe as alot of the time a bust pipe is caused by rubbing and the rest of the pipe especially if its inside the machine is like new. I've not had 1 of my remade pipes with old fitting bust. It honestly works I only use my machines on a farm or doing friends favours it saves you loads of money and you dont lose days cause of down time etc takes about an hour if that once you know wot your doing .
@Ants_Pants
9 ай бұрын
cool idea, i need to look into this
@perrystoll6122
9 ай бұрын
Wow wow what an overhaul. I did not see the total clean down and paint job coming. True ants pants mode. Well done.
@Ants_Pants
9 ай бұрын
Thanks 👍
@tujuprojects
9 ай бұрын
41:10 that thing probably changes the control pattern from SAE to ISO.
@jesseaguayo8568
9 ай бұрын
yes. it is the pattern changer.
@Ants_Pants
9 ай бұрын
cool
@user-yr8hl4zm7p
9 ай бұрын
Hi Ants. You can make jams (e.g plummer inch jams from OBI, or diy wood jams), for rollers grease point tubes and add reinforcing gussets to protect it.
@chrispy3866
9 ай бұрын
Andris, you REALLY need a acetylene torch set up! Work on getting that! It will make so many things so much easier!
@Ants_Pants
9 ай бұрын
yup i do
@nevillesmith9795
9 ай бұрын
I think the Yanmar looks cool with the decals on👍🏼👌🏼
@Ants_Pants
9 ай бұрын
me too
@oc40mg82
9 ай бұрын
I'm glad I found this channel. Been an Andrew fan for a long time but his channel isn't as it use to be. Antspants is the best❤
@Ants_Pants
9 ай бұрын
Welcome aboard!
@roverinosnarkman7240
9 ай бұрын
Bro, taper on hydraulic fitting is pipe thread (supposed to get tighter as it’s screwed in). Lever at the back left is your warp drive (when you want to exceed C on your PTO). Search in your Japanese owner’s manual for “hidden grease zerks” to find all of them (I hate when they do that). Definitely take those buckets to a good Estonian dental tech for some new dentures (teeth are normal wear maintenance items, plus your machine will then be able to consume solid food again!)
@Ants_Pants
9 ай бұрын
gotcha
@TheHomePros6221
9 ай бұрын
1:04:02 the worlds most badass hydraulic foot lever 😂
@Ants_Pants
9 ай бұрын
next one out of 400mm I-beam maybe?
@chrisoakey9841
9 ай бұрын
The track adjuster pins will be covered in grease so rust isn't an issue, but you could mig with stainless wire if you don't want rust. Easier than making a new piston. But since you did drill a new rod, can I suggest drilling in size stages rather than just 1 big drill bit.
@Ants_Pants
9 ай бұрын
took longer yes, but did not have to change tool.
@mick2383
9 ай бұрын
Hey Andris, Mick here. What you call teeth on the bucket are actually the anchors for the teeth. You need new anchors and teeth that slide over the anchors.
@Ants_Pants
9 ай бұрын
ohh lol :D
@59byoung
9 ай бұрын
In the US the tapered threads are sometimes called pipe threads. Maybe that’s actually a natural gas fitting.
@wmsptman
9 ай бұрын
The Control Lever under the floor is to switch your boom and stick controls between ISO and SAE configurations without changing the hoses around. The boom and stick will operate like a backhoe under the SAE configuration. Most people leave a excavator in ISO configuration.
@arifnoor8358
9 ай бұрын
"One guy is crushed and another guy is going to party". Hahaha. That cracked me up. 😂 Great video
@Ants_Pants
9 ай бұрын
😁
@FunfindersX
9 ай бұрын
Great job It looks amazing 🎉
@ZenWithKen
9 ай бұрын
I would bet that unknown control by the seat is to reverse the hydraulic controls, south hemisphere versus north. I mean, you be filling in the hole when you actually meant to dig it. 🙂 To get the live center out of the tail stock, I think you wind it in all the way, then the insert should pop out.
@Ants_Pants
9 ай бұрын
It's labeled as "PTO control" whatever that means lol. Yes you are correct about the tail stock
@Restoringthepast
9 ай бұрын
According to some parts books I have as pdf-files, the lever behind the red one is a P.T.O Control. Do let me know if you want the parts books. It's for a Yanmar B22 and a Yanmar B22-2. Great videos :) Keep em coming. Greetings from Norway :)
@Restoringthepast
9 ай бұрын
I ment B27-2.
@Ants_Pants
9 ай бұрын
Yeah i have that one. What does PTO control do though? :D
@dionwilson6747
9 ай бұрын
Your the man! Great job, looks brand new!! 😊
@LostCauseRT
9 ай бұрын
Fixing up the K-700 is going to be a whole adventure.
@Ants_Pants
9 ай бұрын
gonna rust into the ground before it get around it :D
@Nena84734
9 ай бұрын
Wow, beautiful work, it looks really nice, the decals finished it off, the colors are so good! No CEE this weekend but Ants and Farmcraft gave us plenty!!!
@Ants_Pants
9 ай бұрын
Thanks a bunch!
@williamnoel5092
9 ай бұрын
Excellent video. Love your long videos. Don't make them shorter.
@Ants_Pants
9 ай бұрын
Noted!
@robertstewart7744
9 ай бұрын
Your lathe skills are spot on. Great video.
@sergejstarvids9656
9 ай бұрын
Привет Антс, отличная работа молодец так держать удачи тебе и твоей семье.
@Ants_Pants
9 ай бұрын
❤
@robertpeters9438
7 ай бұрын
Man, I love the way you say URICA!!! When you retrieve A lost part or succeeded in a task!!! I can relate!!!
@Ants_Pants
7 ай бұрын
😅
@tortuegeniale3044
9 ай бұрын
Very good job, as usual 👍
@overtsolutions1426
9 ай бұрын
This guy is gonna be a big channel if he keeps it up.
@Ants_Pants
9 ай бұрын
Higher, further, faster
@goboyz8016
9 ай бұрын
Your videos are a lot of fun to watch by the way!
@Ants_Pants
9 ай бұрын
thanks
@everestyeti
9 ай бұрын
Really good job and I really like the improved paintwork, like you say it would be beneficial with a roller cage or cabin. Hopefully the folks at Yanmar are watching this, you never know they might send you some freebies.👍
@Ants_Pants
9 ай бұрын
😇👍
@jimlong527
9 ай бұрын
Fantastic repair series and entertaining got to love these videos.
@IWH777
9 ай бұрын
DUDE YOU CAN HAVE A 5 HOUR VIDEO AN I WOULD BE STUCK TO MY CHAIR... THE STUFF YOU DO IS SOOOOO VERY INTERESTING.... YOU KEEP ME ON THE EDGE OF MY SEAT ALL THE TIME YOU DO WHAT YOU DO... YOU ARE A WIZARD OF ALL THINGS; IT DONT MATTER WHAT IT IS YOU CAN MAKE IT WORK IF NOT THEN YOU CAN SHIFT GEARS AN MAKE IT WORK ANYWAY... I WILL BE LOOKING FORWARD TO THE NEXT VIDEO AN THE NEXT ONE AN THE NEXT ONE AND AND AND ETC ETC ETC.... MAKES ME WANT TO DO A SUPER VIDEO WATCH OF ALL YOUR VIDEOS AT ONCE... BLESSINGS & AS ALWAYS BE HOPE FILLED F-R-A-N-K-I 🦾🦾🦾🦾🦾🦾🦾🦾🦾🦾🦾🦾🦾🦾🦾
@Ants_Pants
9 ай бұрын
Thanks Franki
@thomas4844
8 ай бұрын
The Craigslist overhaul looks great. Plus your humor makes for some very entertaining content.
@Ants_Pants
8 ай бұрын
hey and thanks
@AW-Services
9 ай бұрын
Another great video, Andris. Some great fixes. Is that lever that does nothing a slew lock. To lock the machine from slewing or turning independently from the undercarriage
@Ants_Pants
9 ай бұрын
Could be? it was not hooked up to anything though, or it was rusted away, i have not been able to get a service manual for this unit and the parts catalog does not say anything about that thing.
@AW-Services
9 ай бұрын
@@Ants_Pants messaged you on Instagram with a parts manual and exploded diagrams. Austin
@mm9773
9 ай бұрын
Love the paint job, especially on the blade. Now you just need to go back and paint the rest black, too.
@michaelkoon8371
9 ай бұрын
Ants wrong fitting for that
@MazeFrame
9 ай бұрын
Learning how to operate a lathe is both rewarding and terrifying. It will open up a lot of options in terms of maintaining your equipment.
@carlosramires3304
9 ай бұрын
Thanks for sharing it with us and no video is to long
@Ants_Pants
9 ай бұрын
thanks
@willwade1101
9 ай бұрын
That fitting is an NPT fitting. it's supposed to stop the fitting from leaking as you tighten it but I've always had to put thread tape or pipe sealant on the threads to keep them from leaking. NPT stands for "National Pipe Thread".
@Ants_Pants
9 ай бұрын
got it boss
@SwampS22
9 ай бұрын
More than 2 hour! What a great moment when I saw that after work 😍 Andris, good look with your restored sky blue baby 😎
@Ants_Pants
9 ай бұрын
thanks
@goboyz8016
9 ай бұрын
That fitting has NTP Pipe Thread. They are used for high pressure fittings and the taper is why it doesn't need a washer or anything to seal it.
@andrebons8711
9 ай бұрын
Watched the whole video in one piece and it was so entertaining that I didnt realise how long it was. Thx alot for it 👍
Пікірлер: 1 М.