By far the best fork service video on KZitem ... informative/well presented/well filmed ...top guy👍
4 жыл бұрын
I would like to say thx u. I changed fork oil and recognized that last servisman assembled fork in wrong order. SPRING - PRELOAD TUBE and than WASHER.!!! Now I reassemble fork according to your video. Regards from Czech
@brianravenscroft3385
Жыл бұрын
Great work mate. Best video I've seen and I enjoyed the precise information. All the best from South Western Australia🤛
@paulmckell7726
Жыл бұрын
Best video I've seen re fork service, thanks
@garyprice2869
Жыл бұрын
Fantastic video!
4 жыл бұрын
Hello, I did everything as your video, exactly, but now I have a noise on one, like the spring rubbing the inner fork on the upper part. Disambled everything and still is...
@GeneralElectricCNC
3 жыл бұрын
Thank you Very much for the videos! Very Professional and step by step instructions. Just like if you were training me as a new employee. I just had to replace my FJR rear shock with a top of the line Ohlins, and noticed one of my fork seals leaking. 40k on the bike so doing good. You just saved my Bacon because I can now afford to do the job myself. Can you give me the dimensions of your nylon driver/installer? Thank you again.
@beebeer
4 жыл бұрын
Very impressive 👌
@Computrackboston
4 жыл бұрын
Thank you!
@rodmitchell8064
3 жыл бұрын
Top cap “o-ring” from Yamaha is P/N 93210-40N50-00 ,$3.15 ea. 2014 Gen 2 diagram
@cliffordhanson3209
20 күн бұрын
I would like to send you my 2006 r6 forks to get the fork seals replaced how much does it cost? To have it done.
@barbarianridexperience
3 жыл бұрын
Hy thanx for all info ...Hou mutch mm is long the metal hose for put out the oil ???
@regulardad-lr2ox
6 ай бұрын
What do I do if my Gen2 fork bushings are stuck during dis-assembly?
@georgetech380
Жыл бұрын
Hi I was wondering if you can help me I have the 2006 model ,I have order after market hyperpro springs but they are longer ,and in some fjr forums says I have to omit the top 15cm metal spacer tube Any idea if this is correct ? Have you ever fit hyperpro on fjr ? Thanks
@angelman4164
Жыл бұрын
You only installed 2 bushings. 2006 and newer have 3 per fork.
@pourkis341
3 жыл бұрын
when I have a leak from the preload setting what should I do?
@Computrackboston
3 жыл бұрын
There is an o-ring in there that needs to be replaced, but you cant get it from Yamaha without buying the cap. You can remove it and match it at a local shop that sell o-rings, or measure it and order them from a supplier.
@pourkis341
3 жыл бұрын
You can send me your email?
@Computrackboston
3 жыл бұрын
@@pourkis341 peter at CompuTrackBoston dot com
@rodmitchell8064
3 жыл бұрын
@@Computrackboston top cap o-ring is Yamaha P/N 93210-40N50-00 , $3.15 ea. , (2006 Gen 2)
@georgetech380
3 жыл бұрын
Hi oil gap should be 104 or 100mm? Thanks
@Computrackboston
3 жыл бұрын
Air gap is a tuning variable that can be tuned to a specific rider's needs. We have found that the air gap that works well for most riders on the FJR is between 120 and 150mm.
@georgetech380
3 жыл бұрын
@@Computrackboston Many Thanks for that ,I was asking because at all fjr forums they say 100mm . Regards from Greece
Пікірлер: 24