Thank you very much. You've helped one more person even after you've gone. May you find the clearest skies and fly free forever.
@madforit9661
5 жыл бұрын
Still continue to help, even though your in heaven.. Hope your flying high mate. God bless
@dazzdoodlzfpv1020
4 жыл бұрын
ive been searching for 24 hours for this information, ive had set back after set back i was about to give up on the hobby, (literally had what had up for sale) now im flying all thanks to yo, so sir i thank you legend and i will sub and like u are now my bible.
@JR-kk6ce
6 ай бұрын
Rest in peace buddy. I haven't forgotten all your help. See ya, hopefully not too soon friend.
@Charliebob2006
4 жыл бұрын
Still helping us guys fly...thank you and R.I.P
@argyriosdaskalopoulos9930
7 жыл бұрын
Dude thank you so much for this vid. There's been so much speculation and talk on how to power this FC and glad that there is a definitive way now. I just got the F4 Omnibus as I really wanted to try something new. Let's see... glad to see your channel is back up and running. Been following the "saga". Welcome back Falcon👍
@ProjectBlueFalcon
7 жыл бұрын
Thanks bud. I just got the F4 Omnibus as well. Just got telemetry working so videos will be coming soon.
@Coreycry
7 жыл бұрын
I didn't know you before but your explanations are crystal clear, and very informative (double vBat, historical pin out, voltage regulation) I'll be sure to watch the whole playlist, hoping you explain how the "shorted jumpers" work, so they activate different pins functions.
@BrunoAnt
7 жыл бұрын
JC Thanks for the videos for Omnibus FC's! And once again welcome back dude!
@ProjectBlueFalcon
7 жыл бұрын
Thanks bud. Working on the Omnibus playlist right now in fact. Should have some videos uploaded by tomorrow morning.
@AngeloIelardi
6 жыл бұрын
You're still here, keep teaching us how to power our flight controllers, one year later. RIP bro, I flew for you today
@nosmokingnl
7 жыл бұрын
Thanks for the video, that cleared a few questions. I do have 1 more, hoping you, or someone here might have the answer. I am powering my FC through the 4in1 ESC connector (J21). I also want to have battery monitoring within the OSD. I connect pin J4 directly to my Lipo. Would this conflict, using 2 power sources with different voltages? As the FC is powered through J21 (v5) and J4 (vbat)
@ilomega1
7 жыл бұрын
I just powered a f4 pro, via the current sensor pads. direct from battery. everything worked perfekt. but when I plugged in the 3 pack. the f4 pro died. No light at all. messured and it got power. and still powered the reciver. I did not overheat. and ran the camara and transmitter of the pdb not fc. I'm going to rma it. but can I supply it a other way so voltage spikes or whatever don't kill the next one. I just really want the voltage to the osd. thanks
@nandakoryaaa
7 жыл бұрын
Thank you very much, a very clear explanation which I did not find in other places.
@RexSmithII
7 жыл бұрын
im doing a 6s build and i have the omnibus f4 osd flightcontroller. is there anyway to hook up the vbat with this type voltage with the osd working. i just realized i think this board is 2-5s direct power connect. i could always connect the vbat with vreg off of the pdb to keep voltage in its limits but i would loose the correct voltage for osd to give me correct readings any thoughts? thanks
@sisvsbro5430
7 жыл бұрын
During soldering the "BAT"-PIT and "Om50"-PIT were connected and I couldn't remove the soldering point very well. So that when I used my LIPO, the Omnibus F4 "Om50"-PIT made a short sound. My F4 is still working with the pc. Is there any possibility to still use it? Sry for bad engl
@TAYGAONUR
6 жыл бұрын
Help Help. When I plug in my omnibus f4 v3 to battery , green light comes up but not the blue ( boot) one and that’s why it can’t be flashing firmware on beta flight . Any idea? Think it’s fried ?
@BrassStacks
7 жыл бұрын
I just accidentally touched + from the battery to Batt+ on the In side of the current sensor and Batt- to the positive out side of the current sensor. it sparked and melted the solder on the pads I had tinned, but I didn't see any magic smoke. Did I kill the board or maybe just the current sensor?
@malcdickinson06
7 жыл бұрын
Powered it all up, can spin the motors but I have Runcam swift 2 OSD but no on board OSD, is there a problem or am I just missing something.
@renatobfa
7 жыл бұрын
I have had some interference in the FPV video with the Omnibus F4 Pro V2, despite feeding the FPV gear seperatly and through a LC filter. So, my only conclusion is that this current sensor in the FC is somehow interfering with the image. Any thoughts?
@raptr49
6 жыл бұрын
When I power up, the flight controller and receiver get power, but not the servos. I tried another F4 V3 and had the exact same problem. If I connect the BEC from ESC, everything works. It seems like the servo 5 volt rail is isolated from everything.
@saswatahira
7 жыл бұрын
removing the linear voltage regulator from the bottom of the board and powering the 5 volt pin with a 5volt switching regulator (ubec) and keep the vbat pin connected to the main battery is the best option. then you get to see the voltage, your board will not fry from the excess heat from the linear regulator and the switching power supply can supply about 3A which can easily provide enough power for the board and the camera.
@gabrys103
6 жыл бұрын
saswata hira I think there is my problem when I try to run fc on plane then after few seconds motor stops. Probably there is less voltage when motor run. Could you please tell where is this regulator? I have Omnibus F4 v3
@jakeb2339
7 жыл бұрын
I have the F3 OMNIBUS V2, have it hooked up the same way, and it wont power on. it works fine when powered by micro usb, I've resolderer the jumpers, no luck any help would be appreciated, but I feel like im going to have to use a different flight controller
@crispystixfpv2479
7 жыл бұрын
so with the f4 pro v3 how do you put it into boot mode and If I was connecting a flysky receiver via ibus which pads would I solder together and do I leave them soldered?
@MylesShannon
7 жыл бұрын
Any idea if the Omnibus F3 nonPro can take a 4S LiHv battery directly to vbat? All I can find is a 2-4S rating and nothing about HV.
@seanbittner7136
7 жыл бұрын
Can I power this board with only a 5v Bec through the PWM plug and get a voltage readout somehow? I don't like the idea of powering it with 16.8 or 13.5V. Thx.
@markthompson8659
7 жыл бұрын
JC I installed one of these F3 boards and it flies great. Until today I plugged in my battery and the buzzer stays on all the time and the red light on the board stays on! Any ideas?
@yksikaksikolmen
7 жыл бұрын
When connect sattelite reciver. Do you have to power the board from battery to bind ? I have 3.27 v with usb conected. Cant get it in bind mode. I have done the cli command.
@ricksquebecrc4627
6 жыл бұрын
hi ! i need your help , i `ve been watching all your videos, step by step about this board but something is wrong with mine i guess , flashing went fine , config , receiver tab , flight modes , everything works fine ,i have aetr1234 in betaflight , mode aetr with taranis , i have this bf 3.1.5 omnibus f4 v2.1 and when i power it the same you do i have a steady green light but no blue light , (blue light only with usb) and in motor tab by increasing ( motor #1 it moves servo #8 )and my motor spins , i`ve check voltage on all pins and sbus pins=1.9 volts ? normal
@jillbencic9143
7 жыл бұрын
Problem:. when i plug in my battery no Leds go on. when i plug it into my computer via USB everything works fine. when both battery and USB connected, my quad connects to my taranis and everything works fine. then when i unplug the USB it goes dead. is it a fixable problem?
@ProjectBlueFalcon
7 жыл бұрын
It should be fixable. I'm not sure what part is bad on your board though. You would have to check with a multimeter.
@nathanatwell
7 жыл бұрын
Project Blue Falcon Gentlemen, I had the exact same issue. I replaced the large voltage regulator on the back of the board and this resolved this issue. Not sure why these boards are shipping with faulty V-Regs, but this was my solution.
@Kradle
7 жыл бұрын
Same thing happened to me after pulling my board off 1 build and putting it on another...I worked around it by running 5v from a separate 5v regulator to the Ram in/out pads next to the OSD pads.
@nathanatwell
7 жыл бұрын
Kradle ^Thats assuming your board is getting power already. Our issue was that the board wasn't getting any power from VBAT to begin with.
@Kradle
7 жыл бұрын
@CircuitStar - I think you misread my comment...feeding the board 5v of power from an external stepdown fixed my board not powering up from direct lipo power. All Vbat is being used for now on my board is telemetry voltage (still works strangely enough, just doesn't power the board.)
@DangerDavefpv
7 жыл бұрын
is it bad thing to be using stock impulse alien pdb to power my omnibus f4 pro v3 along with tramp vtx and esc's? I wanna get current sensor setup but its so complicated and not sure which way to set it up .. what gauge wire ect
@talksickFPV
6 жыл бұрын
Is there any way you could help me with my omnibus f3 pro v2 flight controller? I can NOT figure out its wiring at all and how to get power to it :( i have good pics of both my FC and the 4 in 1 esc I’m trying to wire it with. And pin outs for them. Pleeeeease help 💔
@nucleo1772
7 жыл бұрын
HI PBF I do not understand everything, I'm new to this hobby but I was watch all yours videos and still nothing. I plug the usb to F3 V1 omnibus and my uart 2 (sbus rail) produces 5v(4.5V) and in the INAV tab(receiver) there is no reaction to the motion of the controller but on F4 Pro I see AETR they move perfectly so the sbus working.....maybe there is not enaugh power from usb soo I put power from 3s Lipo....and NOTHING :(
@jeff57
7 жыл бұрын
You are back! Awsome.
@ProjectBlueFalcon
7 жыл бұрын
Glad to have you back
@saliksheraz6236
4 жыл бұрын
Very good explanation
@shawnhecker3323
7 жыл бұрын
When connecting the current sensor, you only need to use the heavy gauge wire on the B+ and the output pad on the opposite side of the shunt resistor. The GND connection can be a lighter gauge since it doesn't need to pass the current that goes through the ESC's, only the FC and whatever it's powering. This should save people from having to solder 2 heavy gauge wires to one pad (not much fun).
@Gbloverlol
7 жыл бұрын
Hello. I'm building a iNav fixed wing using omnibus. The GPS I ordered is rated at 3.3v only oblux m8n which pin has 3v?
@comeaun6086
7 жыл бұрын
Thanks! It was pretty confusing and you made it very simple!
@svilenrachev
7 жыл бұрын
Can you tell me where to buy OMNIBUS F4 Pro (v2) with Bec because I decided to order from Aliexpress.com but there write I should use external Bec, otherwise LDO could overheat.I want to be sure that the version of the FC will not overheat.I read that V2 has SBEC 5v3amp and she had no problem with overheating.
@daneyan1985
7 жыл бұрын
Project Blue Falcon Hey, what if you're running a pdb that has a current sensor on it as well. Would that cause a conflict with the current readings i would get?
@andrewpalmer2021
6 жыл бұрын
When wiring the F3 (Non Pro Version) should 14 gauge wire be used from the PDB to the F3? Or was that just for the Pro versions of the FC's? Thanks.
@aviah11
7 жыл бұрын
Great video. By the way 4 linear escs won't cause an issue. Escs that have a ubec and sbecs causes problems.
@TimEckel
7 жыл бұрын
With the Pro you don't even need a PDB, it's designed to connect the ESCs directly to the FC. Much more straight-forward and uses MUCH less room!
@kokoblokoFPV
7 жыл бұрын
im so happy u making videosagain
@peterreilly9740
7 жыл бұрын
im having issues getting my receivers to work its wired to sbus and comes on and binds but betaflight isnt reading it on any uart i gone thru 3 fcs this weekend n cant get anything to read
@tinahuang8369
6 жыл бұрын
If I use dsmx receiver, what should I do with the PPM/SBUS pin, just let them off ?
@ryandconan
6 жыл бұрын
Hi, I want to ask about omnibus f4 pro V2. Fyi, I want to run an INAV into it in a flywing model. So, here is the thing, I connected the Sbus port from the FC to the Sbus port on the FRsky receiver L9R. after that, I connected the usb to the computer. The fc come to alive. but the receiver dont. I dont know what is wrong. on the manual, it written that Omnibus f4 pro v2 has inbuilt bec. it should also powered the receiver isnt? oh iya, perhaps I should mention that I also tried it with the power from battery. the fc is alive, but the receiver just dont. actually I could use an external bec to power the receiver. but if I do that, it will remove the purpose of internal bec isnt it? could you tell me what is wrong? thanks
@ricksquebecrc4627
6 жыл бұрын
i connected my board the same way but when i power my board there is a steady green but no blue light why ?
@davidanderson6222
5 жыл бұрын
Just bought an omnibus f3 and, Yes, I’m here AGAIN, to get expert advice , explained perfectly. Damn, this dude missed !
@MishoIV
7 жыл бұрын
Do I need 14awg wire on ground pad? AFAIK it is only for powering FC so thin wire should be fine, but I am not sure.
@jacobsingh4873
6 жыл бұрын
Can anybody answer this question? Is it possible to connect the FC to a computer to Betaflight also while having the quad powered up with it's own battery. Will this fry the flight controller, and if so how can I connect the flight controller to a computer and also power it from a battery to calibrate esc's?
@bobflyer4346
7 жыл бұрын
F3 Board? Where is the front of the F3 board, I do not see an arrow anywhere in the video's. I am going to order a unit. Maybe the paperwork has the arrow indicating direction? Thanks Bob
@Aspire7
7 жыл бұрын
Copy and paste question. Just really want to know the answer to this, as it'll help me make a decision on if I want to buy the Omnibus F3 or not. Please respond... Hey, those pins adjacent from the USB port (uart1) you said you would show us in a later video to power the vtx and cam from. Well you also said, we'd have to remove any connections from uart1 before plugging into BF because everything could mess up. Does this mean I'd have to desolder the cam and vtx every time I want to plug into bf?
@Aspire7
7 жыл бұрын
Hey, where does the esc (signal/ground) wires go on the F3? You mentioned esc's, but did not tell us this, and I'm not seeing the info in any of your videos in the playlist. Thanx.
@joshgordon2952
7 жыл бұрын
@ 7:24, you're going through the ground wiring for the F4 Pro. Question: can't you use a thin wire for the ground connection between FC and PDB? Assuming your negative battery lead (w/ thick wire) is connected to the PDB, providing a return path for your power-hungry motors, shouldn't there be a comparatively small amount of current flowing through the ground wire between the FC and the PDB? I.e. just enough to power the FC's electronics?
@colelandreneau304
7 жыл бұрын
do you know how much current it can handle. the motor prop combo I use draws about 140 max
@DangerDavefpv
7 жыл бұрын
I need to ask question does omnibus f4 pro v3 support 5s directly off pdb ? In my case the impulse alien 5" pdb I've got power and ground directly into flight controller? I have had weird issues and just other day it fell out sky and flight controller quit working won't connect at all, so now I've got new one coming so I wanna take precautions and do u recommend running esc signal around ground or power for less noise? Sorry alot to read but u always been big help
@itsallgood78735
7 жыл бұрын
Hey JC, I am building the Flip32 F4 v1 (non Pro). Thanks for your recommendation on the LC filter. Do I pass the battery voltage through the LC filter to the FC, cam and vtx? Or, do I only use the LC filter for the camera and vtx? ie, will the LC filter affect the FC's vbat readout on the Betaflight OSD?
@MishoIV
7 жыл бұрын
Can I power the pro version with usb and lipo at the same time? I powered it with lipo, worked fine, disconected and connected usb, again worked fine. Then I connected lipo to try spin motors from beteflight software and bam, magic smoke.
@jonathane8585
7 жыл бұрын
Great video. Whenever you get a chance, can you do a video with these flight controllers, a 4in1 esc to take advantage of the Omnibus 4in1 esc connector, cam, vtx, and NO PDB? Is that even possible? Trying to build something light with only the necessary parts.
@ProjectBlueFalcon
7 жыл бұрын
Yep no problem
@jurgenvermaas1305
5 жыл бұрын
Can you use the full voltage from a 4s lipo on the Vbat? Or do you need to bring it tot 5V with the power board?
@gankedfpv6381
7 жыл бұрын
Can you power the FC from 5v stepdown? Then if the regulator fails, boars is still safe?
@Roberto-cc4el
6 жыл бұрын
hello artist I need advice ... that mini GPS (maybe with a Magnetometer maybe) I recommend for this FC? Omnibus F4 Pro V3 Betaflight Flight Controller Built-in OSD Barometer SD Blackbox for RC Drone ..Banggood. on the frame ... GEPRC GEP TSX5 Viper 220mm FPV Racing Frame RC Thank you
@byronfoster1651
7 жыл бұрын
I'm getting a Armattan Chameleon soon would a f3 or f4 pro or non be better I'm new to this....?
@p.chuckmoralesesquire3965
7 жыл бұрын
I bought an omnibus F4 from banggood and got it hooked up via usb to my PC. My transmitter channels look great in the beta flight app, but when I disconnect everything and power just by Lipo, the second I turn on my transmitter, the quad freaks out and pings my ESC's and even the transmitter starts chirping. You ever seen anything like that? I was able to bind OK, and I know my transmitter, receiver, esc's etc are good, but this board is driving me nuts.
@Roberto-cc4el
6 жыл бұрын
hello artist I need advice ... that mini GPS (maybe with a Magnetometer maybe) I recommend for this FC? Omnibus F4 Pro V3 Betaflight Flight Controller Built-in OSD Barometer SD Blackbox for RC Drone ..Banggood. Thank you
@Aspire7
7 жыл бұрын
Hey, those pins adjacent from the USB port (uart1) you said you would show us in a later video to power the vtx and cam from. Well you also said, we'd have to remove any connections from uart1 before plugging into BF because everything could mess up. Does this mean I'd have to desolder the cam and vtx every time I want to plug into bf?
@lorenzo7788
7 жыл бұрын
F4 PRO v2: it's not clear for me (my fault) if I can power the FC through an external PDB/BEC (with 5V) and still have the battery voltage in the OSD. It seems the only way to fly with 5S batteries without damaging the FC and still have all the info in the OSD.
@leflamantrosefpv1725
3 жыл бұрын
thank you! you keep helping us from heaven;) rip.
@danielscicluna2309
7 жыл бұрын
Hi and thanks for your videos Project Blue Falcon. I have connected Omnibus F4 Pro in VBAT config and everything worked fine. After a crash though I cannot power the FC with battery, but it does light up through USB. Any idea what might went wrong? Thanks!
@JorgePerez-yt9ou
7 жыл бұрын
I'm not having any luck with the flip 32 omnibus F4 or the clone version...the first one I cooked it somehow, and the flip 32 worked for about 5 flights then nothing...I can only power the board through the USB...I watched your video on how to diagnose things you "fried" and I was wondering if you've had this problem with that F4 board more than a few times. I like the features of the flip 32, but is there a more reliable FC I should get with VBAT and OSD features?
@JorgePerez-yt9ou
7 жыл бұрын
ok so the flip 32 omnibus F4 now works if I use a 5V power source soldered to the ESC pwm pad...I am wondering if the power coming in the VBAT fried a diode or something. Can I use VBAT and power the board from a 5V source? I mean the board isn't powering on using VBAT anyway
@darrencrane9371
7 жыл бұрын
I have all the functions working properly but I have no motor function in the motor test tab and it won't arm. The Rx tab shows all my inputs are mirrored. Airbot sent me one of the BEC modules but I didn't connect it. (It didn't include wiring instructions)
@darrencrane9371
7 жыл бұрын
I can not flash new firmware either. I've used the boot button as well as CLI DFU command.
@hadyandharmawan7650
3 жыл бұрын
Still very helpfull today.....👍
@MichaCieplik
7 жыл бұрын
What about powering F4 board from vbat, fc without current, got rather hot after few seconds
@dangthisstupidpasswo
7 жыл бұрын
Very confused. Really need help. F4 v2 pro for fixed wing. Don't I just solder the battery to bat tand ground then power the motor from the motor pad? Won't the servos get power from the fc? I soldered the batt + and -, plugged in a 3s, green light came on for 2 seconds then went out. Now I can't power it from battery, USB, or pwm 5v. What did I do wrong. This is a pain in the butt. Already ordered another one but don't want to repeat the results.
@kermets
7 жыл бұрын
the onboard FC reg is a poor 1.5 amps and not useful for the servos not even a wing.
@raptr49
6 жыл бұрын
No, the servo rail is not powered by the fc because there is a blocking diode that isolate the FC +5v from the servo rail. To get power to the servos, you need to either use the +5v from the ESC-BEC or a separate BEC. See this RC group link: www.rcgroups.com/forums/showthread.php?2874687-OMNIBUS-AIRBOT-F4-family-ESC_5V-Isolation
@skarebsuper
7 жыл бұрын
Is there a specific direction to mount the FC on the quad?
@NickelCityLaser
7 жыл бұрын
hey man, i know its not the same FC but i have a Flip32 F4 REVO, and a d4r-II RX, any chance you or anyone else would know how this thing wires up properly? everything im reading on it is just confusing me more and more.
@ProjectBlueFalcon
7 жыл бұрын
I'll make a video on it right now. Should be uploaded in a couple hours. Just check back later or tomorrow.
@Steve-ou9ed
7 жыл бұрын
Sorry to be a pain, I want to connect mt flysky iA6B receiver with either sbus or ppm I'm totally confused, I just got my flip32 omnibus v2 board from ready to fly quads, do i need to put solder on the sbus or ppm pins ? and thanks for the help the other day. your vids are class
@bobflyer4346
7 жыл бұрын
Betaflight 3.1.6 Flip32 F3 omnibus and Tricopter? First thanks for the great videos! Do you have any information on how to connect the Tricopter tail servo on the F3 board? What motor number output is the BetaFlight used when a servo is required? I understand the resource command and how to use, however, I have not found any info on how the rear servo is mapped to a motor pin output and which servo number to use. I.E. if I had Motor 5 or 6 set to say B07, I would change this to Motor 5 or 6 to none. Then resource the servo, Resource servo xx B07 and save. Not sure which motor number can be used for servo, and what servo number to use? Thanks for any assistance in advance. Bob
@adrianjester2226
7 жыл бұрын
hi thanks for the tips helps alot. abit confuse on one thing thought. what on the last method with the v4 pro without the current reading. what gauge wire should i use from the pdb to the fc?
@yashmacin2208
7 жыл бұрын
What gauge wire do I use for the F3 board? Can I use a servo wire?
@tecnofpv9202
7 жыл бұрын
Can you please link the video for calibrating current and voltage in the description?
@spartan3299
7 жыл бұрын
Looking at configuring a Fixed wing 4channel trainer and then a Pop wing next using the Frsky x6r and x4r and on board OSD. Looking to load INav for GPS support. Plan to start with the ReadyMadeQuads Flip32 Omnibus F3. Goal is to have flight modes, Stabilization, and RTH. Will I need to flip the SBUS? Will I need a Power current module? Will I be able to utilize the Frsky telemetry? Does this sound like a reasonable start point?
@ProjectBlueFalcon
7 жыл бұрын
You don't need a current sensor but if you want current then you'll have to add a current sensor or go with the Omnibus F3 pro which has one built in. But personally I'd add one in because having to run thick power wires to the Omnibus Pro is a major pain. For telemetry the F3 and F4 omnibus will work, but it's easier on the F3 so I would recommend that, plus you don't need a F4 board for INAV anyway, the F3 is more than enough. Yep it sounds reasonable. I couldn't tell you the specifics because I don't do fixed wings, but it is very possible.
@crezzlin
7 жыл бұрын
Thanks for this video.. can you tell me if the F4 Pro will take 5 or 6s direct? Thanks
@Aspire7
7 жыл бұрын
Will the same rules apply for the clone versions on banggood?
@year10zahalla6
7 жыл бұрын
Hello it would be interesting to hear your views of connecting a Spektrum satellite such as the redcon with a spektum transmitter, to the omnibus f3 since it has a dedicated port on the flight controller . I have read some comments that the spektrum is not that compatible with 5.8 video and as a result you might get loss of control with the spektrum over your quad. I appreciate your videos they are superb are superb.
@ProjectBlueFalcon
7 жыл бұрын
I'll look into it and make a video when I find something.
@terragady
7 жыл бұрын
How much I can hook up to that 5V from the FC? VTX, camera, receiver and some WSxxx leds is fine?
@ProjectBlueFalcon
7 жыл бұрын
You can do the camera, receiver, and LEDs, but dont power your Vtx off the flight controller. The video will look horrible if you do, if it even works at all. But everything else will be fine.
@terragady
7 жыл бұрын
Project Blue Falcon yes I can power vtx directly from lipo with some cap. Was just wondering about few leds and receiver as someone said that this 5v is only enough for board itself nothing else
@manuelfernandezraposo973
7 жыл бұрын
Thanks amigo, you are a machine! Helped me a lot ;)
@DangerDavefpv
7 жыл бұрын
Also my f4 that is damaged gets warm plugged up is it normal
@rrrrepairs
7 жыл бұрын
Is there another way to power up the omnibus f3? Mine won't power through lipo only USB.
@ProjectBlueFalcon
7 жыл бұрын
You could place wires from a 5v regulator to the motor output pins.
@rudra9117
4 жыл бұрын
Will it work for spracing f3 flight controller
@RyanGentner
7 жыл бұрын
Quick question, I have the Omnibus F4 Pro V3 and I am connecting it to a 4 in 1 esc with the connector on the bottom of the board and I will be using the current sensor also. The question is do I need to remove the 5v from the 4 in 1 esc that plugs into the flight controller? www.racerstar.com/Racerstar-RS20Ax4-4-in-1-ESC-p-64.html this is the 4 in 1 I have
@ProjectBlueFalcon
7 жыл бұрын
Yep remove the power and ground from the 6 pin connector. It's not needed.
@RyanGentner
7 жыл бұрын
Project Blue Falcon awesome thank you so much! glad to see you are back on KZitem!
@danjensen9425
6 жыл бұрын
Hey do i have a good one, my 250 arms can hover then will disarm and shut down. I have watched all arming issue vids , my build is a 250 frame cheap one , emax 2204 motors , emax 30 amp bullet ESCs , omnibus f4 v3 . if beeper connected it beeps rapidly after shut down. I checked channels to make sure no conflicts with switches. osd works too . i rebuilt it with a new from airbot f4v5 same problem. So next is scrap ESCs and hope for the best. I watched a lot of your videos on omnibus. any help would be awesome, I have a martian 2 same setup but emax red bottoms , only difference in build is i connected all negatives together and soldered to one pad on 250 that has problem and on martian soldered 2 together and onto 2 pads. that shouldn't be an issue but when i scrap the esc for new better ones i will solder all ground wires to their respective pads. thanks glad i have money to spend on quads as all other money spent is just a waste.
@adamk.3946
7 жыл бұрын
Hey man, glad to see you back. I have a question about the F3 omnibus pro (current sensor). I have a TBS unify pro 5g8 v2 hooked up that takes 320mA at 5v, also a hs1177 taking roughly 70mA. I have the flight controller powering everything off of the 1.5a reg with 4s and it works great. I've been told and read that 5s works with these flight controllers just fine, and I've plugged in a 5s lipo and it worked. I'm wondering if you think 5s should be okay for the voltage reg since I'm not pulling a huge amount of mA. Thanks! Merry Christmas!
@ProjectBlueFalcon
7 жыл бұрын
I've seen where many guys are using 5s as well. I dont think you'll run into any problems, but I haven't tried this for myself so I can't say for sure. But I'd guess you'll be fine.
@mikejordan911
7 жыл бұрын
can u use the v cc and ground on the pdb and get voltage?
@bigboyash1
7 жыл бұрын
Hey awsome videos , just quick question , probably a stupid one. How comes you can get away using thinner wire if your not using the current sensor ?
@ProjectBlueFalcon
7 жыл бұрын
Thanks Ashley. If you use one of the Pro versions with current sensor you have to use the same gauge wire that your battery uses because the battery leads have to be soldered to the flight controller first, and then more wires run from that to the PDB. All the current being used must flow through the flight controller first because the sensor has to be able to see how much current is being used. All that power flowing through thin wires will literally melt the wires in half. And even if they dont melt in half then you would only get 5-10% power to your motors. The multirotor probably wouldnt even fly. By bypassing the current sensor and soldering battery leads to the PDB, but placing thin wires on the flight controller, you wont be able to use current, but voltage in telemetry and OSD will still work because voltage readings work different.
@nics2202
7 жыл бұрын
I got the F4 Pro V2 but my 4in1 ESC also has a current sensor, voltage sensor and 5V BEC. Will there be any issue having 2 current sensors in the loop? Or are there inputs on the F4 Pro for external voltage and current sensors so I can run the FC on the 5V BEC? What would you recommend? PS. You're a legend!! Your various playlists have helped me immeasurably and the detail and clarity of your explanations is unrivaled
@Cornflakes691
7 жыл бұрын
Your videos are awesome! How are these holding up on your regular builds recieving direct voltage for so long?
@norb4152
7 жыл бұрын
I learned so much from you, thanks man! So I have the F3 and want to connect it to my matek PDB, so I'm gonna run wires from the big PDB plates (where the escs go for example) to the "lipo" spots you showed in the video. What kind of wire would I use for that? It will take full voltage, but the pins are super small.
@RoadKing05FLHR
7 жыл бұрын
Hi, your videos are awesome. I'm new to these boards and have a f4 pro for a 250. I'm seeing a lot of people who have issues. I want batt voltage on osd but I would like backup fc power if possible. I am not powering anything from the fc regulator that's not on the board. Any ideas on hooking up a bec to power the fc and still get batt voltage? Regards
@nucleo1772
7 жыл бұрын
PBF can you explain how to get servos work( how to get them 5v) I have all done but my servos doesnt move(Flying wing) :((
@raptr49
6 жыл бұрын
The video is misleading one one major point. No, the servo rail is not powered by the fc because there is a blocking diode that isolate the FC +5v from the servo rail. To get power to the servos, you need to either use the +5v from the ESC-BEC or a separate BEC. See this RC group link: www.rcgroups.com/forums/showthread.php?2874687-OMNIBUS-AIRBOT-F4-family-ESC_5V-Isolation
7 жыл бұрын
Great guide! I like the way you're powering the FC from the PDB and still have voltage reading for the OSD. What AWG wire do you recommend to go from the battery pad to the FC?
Пікірлер: 221