You guys were making comments criticizing him can’t criticize him. Where is your video. And then look at your ratings on your video. Then come back and comment and show the link on your video. The customer made you not want to pay for heated floors. This was a video. The time it took to do what he did is about the same amount of time it would’ve taken to put concrete on top of wood. Insulating the floor reduce the Cement and gave more “stability” to the floor overall if the floor was to be changed or drop down in height. He created (( “versatility.” )) But you lame contractors did not think of that. The guy in this video did a great job. Keep up the good work.
@cncsdaddy85
5 жыл бұрын
I've seen this method used for movement and weight purposes as well as cardboard forms used for large build ups most of the guys commenting negatively have never seen a commercial job or been critiqued by anyone else other than a homeowner who know no better
@sandorkolesza3743
5 жыл бұрын
Why He laid that reinforcement screen? Should ift up at least 1 cm! (otherwise useless!)
@garryfwright
6 жыл бұрын
He should have used a semi-dry mix of sand and cement rather than a self leveling compound. Self leveling is meant to correct small deviations in floor height, typically less than 10mm. Sand and cement is much cheaper but requires more skill to implement. Im a plasterer and use it all the time. His prep was very good but I suspect he is a joiner rather than a professional floor screeder. Thanks for posting I learned something from it.
@kevinhornbuckle
6 жыл бұрын
Garry Wright The mesh was pushed to the bottom. Where is the water supposed to go if he's pouring on plastic? This was painful to watch.
@MrMalarix
6 жыл бұрын
It doesnt seem to me be a self leveling compound, but I could be wrong, other than that it's ok
@nuirueu
6 жыл бұрын
There's a few companys that make compund that can do up to 50mm in one pour nowadays to be fair. But i would never use it on a chipboard floor even with that feeble wire he put under it.
@maafumataele
6 жыл бұрын
Hi sand and cement is better materials for that floor screeded but floor level compounds that the wrong materials for that job/ gib board is wet and starting damaged /finishing the floor is not good enough still rough and more cleaning up /prep works all good enough I think you are builder not a solid plastering thanks you very much you done the job but I am learning what you doing and you learn on my comments cheers brother
@scwfan08
6 жыл бұрын
He didn't use self-levelling compound. He used Estrich (screed) which is exactly what you said but he definitely made it way too wet.
@4G63addict
5 жыл бұрын
All these negative comments like everyone is perfect. This dude is a extremely hard worker. Weather it's done correctly or not, give the guy some credit for making a living for his family.
@iambobby3537
5 жыл бұрын
So many videos with, no narration, are bedded with bad music. Love this sound.
@ianmcintyre6498
6 жыл бұрын
I think he's done a great job - Well done !!
@user-wb7we8xv1u
5 жыл бұрын
Всё хорошо, кроме одного!) Армирование должно быть, как минимум, в нижней трети стяжки! Сетку следовало бы приподнять на 2-3 см !)
@kleos_drywall
5 жыл бұрын
Love the knee trolley he's on
@0815SeaBass
5 жыл бұрын
Alter Schwede, machst das aber extrem aufwendig und umständlich, für ein paar qm Estrich. Letzte Woche habe ich 15 qm Estrich ins Bad eingebracht. Sogar noch selbst mit dem Mischer (Rheinsand und Trasszement) erdfeucht angemischt, mit der Karre rein gefahren und mit der Latte sauber verdichtet und abgezogen. Das ganze hat 3,5 Stunden gedauert.
@user-ud7up9zs7x
6 жыл бұрын
Единственное в жизни что все бы хотели, так это делать ремонт с такой скоростью:-)))
@pedromunoz2225
6 жыл бұрын
👍👏👏👏👏👏
@DanielJuniorSilvaSantos
5 жыл бұрын
NÃO AO COMUNISMO!!!!
@Framewood
5 жыл бұрын
x2 рулит
@olegotdelka37
5 жыл бұрын
Это што за хуйню он тут делает ? И не песко бетон и не налевной. Нахуя ?
@PiratDim
5 жыл бұрын
@@olegotdelka37 как раз стяжку и делает. глянь, что такое у него в мешке- baumit EB 42
@charlesdefrancisco5056
6 жыл бұрын
What incredible talent....this craftsman is got a lot of talent and in my experience with this process he could teach many from his very professional job. If he is ever looking for a job ..I would hire him in a heartbeat..well done
@adangerousidiot
5 жыл бұрын
I don't understand these comments that he's done a naff job. He has done a good job, I suppose he finishing off with tiles.... Personally I don't like it's all in the bag mixes......never heard off a screed bag mix. I think he was using postcrete .;o ) I'm self employed and always work on a price, so on his side. It's easy for anonymous people slag everything off, fair comment is good but don't bad mouth just for sale of it. What you people out there think. Regards to you all
@armandodemichele1420
5 жыл бұрын
adangerousidiot, The end result is good, in the end I guess that's all that matters. I am a master tile-setter, I install tile marble, slate, and also terrazzo. Many newer installers do it this way, but I know the old ways of the trade. I mix the sand and cement myself, and I don't waste time with those leveling ties on the walls , and that is because of the cement and sand ratio I use has less water, and holds up. It is very difficult to write and explain my method here. I think he did a good job, even though he would go broke around my parts of the world with this method if it takes him more than 3 hours to do this job ( alone with no helper).
@matthewimi
5 жыл бұрын
A lot of detailed work for such a small space. Takes a lot of patience and dedication to the process to get results like that. Hats off to you.
@krzysiekm1641
3 жыл бұрын
Egal wie gut du deine Arbeit gemacht hast, Der Cheff wird immer zu dir sagen dass es schneller und besser hätte sein können
@edwardmcgarry7917
5 жыл бұрын
most excellent job completed by a solitary professional
@johncoops6897
5 жыл бұрын
Wrong. It's probably the most UNPROFFESSIONAL attempt at levelling a floor that most builders have ever seen. There is so many mistakes it's not funny. Having enough money to buy a cheap laser level and a metal rail for your circular saw does not mean anything whatsoever about the quality of the result.
@richardsimpson3136
5 жыл бұрын
Have to agree with that Edward!
@totoleheros7506
5 жыл бұрын
@@johncoops6897 maybe you are right with the unprofessional, I don't know. But you are wrong with the cheap metal rail for his circular saw. Have you ever seen how much this Festool saw and rail cost? Far to be cheap, it is top end tools.
@johncoops6897
5 жыл бұрын
@@totoleheros7506 My word "cheap" related to the laser level. Yes, I know that those rails are expensive, however my point is that no matter HOW much equipment you use and how much time you waste, this is not the correct way to do this task. It doesn't NEED to be level... in fact the entire point of such a wet area floor is to not have it level, but to have a fall towards a drain. Also, the final surface levels and flatness are sorted out by the tilers, who place the tiles on a 3 to 10mm thick bed of adhesive. They set the levels on the *tops+* of the tiles, not the bottom, and it doesn't matter whether the underfloor is perfectly smooth or flat. It's a total waste of time to create an underfloor at 0.1mm accuracy when the following trade doesn't even use that surface as a reference point.
@leviledbetter
4 жыл бұрын
This is a man who enjoys his work.
@Anoncore1
6 жыл бұрын
Aside from using this type of concrete for a more then 1/2 application ,the prep was impeccable , a little over the top , but great job....mesh ,this type has to be pulled off the ground to be doing its job , and not proper again for this type of mortar or ciment what ever you want to call it. Why so thick tho? 3/4 substrate is more then enough for code in my neck of the wood....anyway , in the end , love the attention to detail , minus final choice of material for levelling .
@tootman001
5 жыл бұрын
attention to detail is superb , I wish I had his patience job well done!
@sisconcorpindustries9755
6 жыл бұрын
Excelente trabajo maestro me impresionó cuando empezó a usar el láser y cada detalle de su trabajo gracias.
@zurzurshahean6262
6 жыл бұрын
عمل رائع وكامل اتوقع نتائج ممتازة و ناجحة جيد انه لم يستعمل البيتومين و لفائف العزل شكرا لك مقطع مفيد
@yekoJhgg
5 жыл бұрын
This is for two people you did alone! Good job!
@R0B0PR0P
5 жыл бұрын
At this point the client decides they want UFH or the spark remembers he didn't lay a cable 😂
@saschafunk1644
6 жыл бұрын
Habe dieses Jahr auch mein Bad im Altbau saniert. Der alte Bodenaufbau war interessant. 2 Lagen Fliesen, darunter Spanplatte gefolgt vom ursprünglichen Dielenboden. Spanplatten und Dielen waren total verfault, weshalb die Fliesen auch abgesackt und gebrochen waren. Zum Glück waren die Balken mit einem Querschnitt von 35 x 35 cm aus Eiche kaum betroffen. Laut Chronik, wurde das Haus 1536 erbaut. Zwischen den Balken befindet sich gestampfter Lehm. Habe den Boden mit Dampfbremse ausgelegt und das Trockenestrich System von RIGIDUR installiert. Hat wunderbar funktioniert und war an einem Tag erledigt und sofort begehbar. Restlicher Bodenaufbau mit Feuchtraumversiegelung und Klicklaminat aus Kunststoff vollflächig verklebt.
@giovannigjini7061
5 жыл бұрын
Sascha Funk
@NikE-vn6dw
5 жыл бұрын
Sascha Funk ggg
@user-rd2cr3tx7h
5 жыл бұрын
Sascha Funk yg
@sgt.davideswigerusmc5113
5 жыл бұрын
Above and beyond. Nice work, I'm sure it was a design thing of the customers to raise it like that (the man with the money is almost always right). Of course I don't know how he could make any money moving as fast as he did 🙃😝, still you can't say he wasn't thual and completely well done. This job will never come back to bite him.
@Burningquest
6 жыл бұрын
Eure Videos sind immer ein Genuss anzusehen.
@Randy_84
6 жыл бұрын
This is amazing! Great work!!
@jedruskmicic1167
5 жыл бұрын
spierdalaj
@daanvreugdenhil
6 жыл бұрын
Due to the speed of this video, it sounds a lot alike Scrat, the Sabre-Tooth Squirrel from Ice Age, Sniffin' around with his acorn...
@nially85
6 жыл бұрын
How did u even think of this?but sooo correct!!! Pmsl
@JoaoPereira-gz2zc
6 жыл бұрын
You know what I did? Sped it up to 2x. Awesome
@chukwow5738
5 жыл бұрын
Hahaha yes, that was my thought also. Had to go to the comment section to see if it was only me LOL
@Chelovik_NZ
5 жыл бұрын
Or Benny Hill ... it only needed the music to make it so .... however, it was a good watch and I did learn a few tips
@whitenoiseihearu4018
5 жыл бұрын
He worked hard for his money...respect.
@odonion1
5 жыл бұрын
Wer hier kritisiert, soll zuerst seine Arbeit zeigen. Von mir ein Daumen hoch.
@gilgilofgil5476
6 жыл бұрын
2 малярных маяка 20 минут работы - качество тоже самое (прикольная задумка с приспособой для выставления лазера)
@mariocapuleti8618
5 жыл бұрын
Ano i vidna shto u vas v Rassii kacestva lutshe cem v Italii ...... nu vy i pridurki kaneshna ... 2 maliarnyh maeka 🤣🤣
@SaratovFilm
5 жыл бұрын
@@mariocapuleti8618 Качество везде на самых разный уровнях. Придурков и у вас хватает, поаккуратнее с ярлыками.
@sweetiepienumber1
6 жыл бұрын
He's fast! He's got good tools. He's done this before. And that = getting paid here in the U.S.
@arpadprp1778
6 жыл бұрын
How about guarantee..
@putusutama
5 жыл бұрын
@@arpadprp1778 no guarantee 🤗😂
@javierzapanacaceres2933
6 жыл бұрын
He has done a good job, why people always tried to find minimum errors in what other people do and people who critizace him have never even cut a log.
@ulfhofling3218
6 жыл бұрын
I've been doing floors for more than 10 now. What was he doing with the screed
@tonygibbs9821
6 жыл бұрын
If this is an embarrassing standard of work, then I'm afraid a majority of professionals of their trade should be thoroughly embarrassed!
@Maxmustermann-e8i
5 жыл бұрын
@@tonygibbs9821 I'm pretty sure the title is the result of a bad automatic translation. Nobody wants to embarrass the guy. Some of the comments are unfortunate tho'.
@DanielR577
5 жыл бұрын
The screed used is Baumit Estrick EB 42 which is a dry type of screed with only 4 liters / 35kg pack, not a self leveling liquid type, hence the decomposing when mixed and poured out like a selfe leveling liquid type of screed. This is printed on every package. When prepared properly the screed is described as a stiff to plastically/kneadable composition. If the majority of professionals is applying great and expensive material is such a way they should be thoroghly embarrassed. ch.baumit.com/produkte/estriche_boden/estriche/baumit-estrich-eb-42.html
@Ewoodster
4 жыл бұрын
This is translated from German and "Bad" means bathroom in German. It has nothing to do with bad work, he is dong just fine as you pointed out already.
@mzmgla
4 жыл бұрын
na ob da der wasserzementwert stimmt ! ?
@orcaazur06
4 ай бұрын
This man allways have great videos. Just one question : is it estrih ?? 👍
@ruthatondo4389
6 жыл бұрын
Beautiful. What a nice and fast work. 😵😊😄😄😄
@Bosoiy
6 жыл бұрын
для лучшей работы сетки было б неплохо под неё подложить закладки и сделать слой сетки в середине заливаемого раствора.. И саму стяжку разделить на 3 сектора демпфером..
@ivanovaleksandr9965
6 жыл бұрын
Ну и логика у тебя, куклин. То ты кладеш сетку в середине, чтобы стяжка была одной целой, а потом демпфером хочешь разделить её на три части. В данном случае сетка отлично выполняет свои функции (предотвращает от разделения единой стяжки на несколько частей). Не обязательно класть сетку именно в центр стяжки, а желательно положить в нижней части.
@rotmensrrrotmensrr924
5 жыл бұрын
Для сетки нужно 1-2см защитного слоя....
@rotmensrrrotmensrr924
5 жыл бұрын
Клоун тот кто етого незнает)))))))))))))))))))))))))))))))))))))
@Bosoiy
5 жыл бұрын
бетон хорошо себя ведёт при зжатии,при растяжении для того,что бы он остался целым ему необходима арматура.Чем больший кусок стяжки (или бетона)есть-тем больший температурный коэфициент (растяжения-сжатия )на него воздействует. Разделение стяжки на зоны способствует сохранению целостности структуры сделанного изделия в более длинный период нежели дожить до зарплаты.
@user-cq5rw1ke3u
4 жыл бұрын
Мудрые советы, тот кто слышит тот поймёт.
@johnmehaffey9953
6 жыл бұрын
It would make a floor screeder weep when ever I saw any professional screeder in action it was a semi dry mix and then screeded, then done with a wooden or plastic float to get a finish, never in all my days in construction have I ever seen a floor put down this way
@stephbhoy1
5 жыл бұрын
Agreed. If he's goin to mix it so wet, then use self levelling compound then there's no need for a straight edge.
@jorgeguanche5327
5 жыл бұрын
How to do it wrong......Jesús christ!
@zorroonmilkavitch1840
5 жыл бұрын
@@stephbhoy1 pretty sure that's self leveling compound with price pretty high much cheaper to go with this mix
@darrenkaspers9331
5 жыл бұрын
Wrong, can't use self leveling compound it's too deep, you'd need a few hits at it, with wet gear like that, once levelled and going off it needs a steel trowel finish. But let's be honest he done it all wrong lol
@darrenkaspers9331
5 жыл бұрын
@Glyn Owen I've never seen it, only selfleveling you have to mix with sharp sand to bulk it up. Also as the gear he's used is do wet the drying time would be over a month before a floor covering could be put down.
@AJ-ds5gf
3 жыл бұрын
nice trick with the laser level, using those pieces of wood like that to slide it up and down. I'm stealing that idea =D
@nurqe12
5 жыл бұрын
Good job mate at least you finished it. Seeing all the crappie plumber job I like your job better 👍
@michaelhermann9990
6 жыл бұрын
Estrich kenne ich erdfeucht, man gut das da noch Fliesen draufkommen- aber mit 10mm Zahnung den Kleber drauf, damit die Huckel überbrückt werden.
@rainergodel4144
6 жыл бұрын
Michael Hermann Das sehe ich genauso 😉
@bronchiosaurus2766
6 жыл бұрын
is das nicht fliesetrich der extra dünn ist um sich selbst zu nivellieren? die armierung scheint mir nur etwas tief, sonst alles richtig gemacht in meinen unfachmännischen augen.
@bronchiosaurus2766
6 жыл бұрын
ok vergiss was ich geschrieben hab, da fliest garnichts...
@MrKloetze
6 жыл бұрын
Da muss schon min. eine 15mm kommen! Das der Kerl sich nicht schämt so nen scheiß zu veröffentlichten, jeder richtige Fliesen oder Estrichleger hätte Ihm was erzählt.
@stefanguido6546
6 жыл бұрын
Du hast recht. die nasse Pampe schwindet, da wird dir jeder Fliesenleger einen Rapport vom feinsten herauslassen. Die Ecken werden sich stellen, Risse auftreten.. Nacharbeiten kosten mehr, als der Estrich. Heimprojekt, mehr nicht.
@mattmotta859
6 жыл бұрын
how does that thing stay level when he keeps moving it
@Assmodin1981
3 жыл бұрын
I like the clipping sound of the tacker 👌😄... and next time use a mouth guard mask ;-)
@philelliott5340
5 жыл бұрын
Great work, nice job, give him a pay-rise! - Phil
@SST23
4 жыл бұрын
everything was ''ok'' until he tries to level the floor...omg.
@junglebunny5673
6 жыл бұрын
can someone explain what he did wrong. looks ok to me
@johnknoefler
6 жыл бұрын
The process of screeding (leveling off by pulling a board across the wet concrete) was left a bit rough. It looks fairly level so it's ok for placing tiles. That's why there was no finish floating done. The few rough spots can be ground down with a diamond abrasive wheel so it's not big deal. In all fairness, it's a really awkward place to work. The lighting was crappy and you really need good light to see what you are doing. Plus, no one was there to help him. Also, he had poor tools to do the job. All in all, it's satisfactory considering what it's for. Basically, tiles are going on top of it so it's no big deal.
@junglebunny5673
6 жыл бұрын
i assumed he was going to tile it.
@evanpenny348
6 жыл бұрын
Johnknoefler That's not really the point. Leveling a floor in this way is difficult and imprecise. Despite the initial use of a laser level it is not practical to achieve a good result by sort of winging the screeding in this way. Many years of practical floor tiling convince me that this is not an easy job in the best of circumstances, carpenters do not understand the tolerances needed, and a better system of perimeter boards to screed to are needed. Well done to the flooring guy for his job, but not overall a noteworthy system.
@johnknoefler
6 жыл бұрын
Honestly, his screed technique was a bit clumsy but it will pass.
@anitatrent6102
6 жыл бұрын
johnknoefler I
@user-fn9sw9ll2n
4 жыл бұрын
Блин,я так же работаю один.😅 Тяжело очень. Молодец, мужик! Единственно что плохо,то этот пенопласт-он просядет под весом стяжки и в дальнейшем будет тоже тихо,день за днем,просаживаться и плитка с пола будет отходить.Появятся щели и пипец.
@stephandevriesere3667
6 жыл бұрын
Ich wünschte, ich könnte so schnell arbeiten, dann war mein Badezimmer fertig, hahaha
@AMLO-4TA.TRANSFORMACION
5 жыл бұрын
Man I just notice that he started working when it was daylight and he ended with a not so hot lamp, lets give the man a hand. With no help and no real tools and maybe no Home Depot around.😭 I know, that sucks.
@enverkement534
3 жыл бұрын
11qq
@wwsjr2
6 жыл бұрын
Where is the drain? Guess I missed it.
@migrationfuntimes303
6 жыл бұрын
that will be any lowest point at the wall junction.lol
@Blankanik
5 жыл бұрын
graham smith This is the point. If there is no drain, the floor can not be flat. It has to be up to 1cm (3/8 ") high by the walls, and lower in the center.
@7thfloorisnomoreq790
5 жыл бұрын
ive seen a shower floor been poured clearly it was done wrong. this is a professional. glad i now know the correct way
@malcolmdastur4411
5 жыл бұрын
Amazing video to watch. I don't know how long the whole job took to do but the guy worked hard at it continuously. This is the sort of worker that you would never find in Canada as the only workers I've ever come across are the lazy cut corners workers. Canadian workers charge the most, to bodgit and legit. Oh! that would be a great name for a Cadadian construction company.
@nonyabuisness
6 жыл бұрын
He did everything perfect.... until the concrete
@stefanrudolf6477
6 жыл бұрын
Kommt die Armierung nicht in die Mitte des Unterlagsboden?
@udos.2987
6 жыл бұрын
nein, wieso?
@stefanguido6546
6 жыл бұрын
Hängt vom Lastfall ab.
@stefanguido6546
6 жыл бұрын
Stimmt, da unten macht sie überhaupt keinen Sinn. 1/3 Überdeckung. Entweder oben oder unten. So hätte der gute Mann einen 100€ Schein in die (zu dünne) Brühe werfen können, wäre genauso sinnvoll.lol.
@andreasmuller7932
5 жыл бұрын
In der Mitte ist die statische Nulllinie, also ist da die Armierung weggeschmissenes Geld. Sie muß ins untere Drittel, dort treten die Zugkräfte auf.
@f.dortmund4593
5 жыл бұрын
In dem Video ist einiges nicht nach der anerkannten Regel der Technik gemacht worden. 1. Randstreifen tackern ist ok, aber man sollte an die Schallübertragung denken. Dann sollte man diese nach dem verlegen der Fliesen erst abschneiden. 2.Dämmung nicht versetzt verlegt! 3. AKS Gitter zu tief und zu nah an der Wand ( man sollte etwas Luft lassen)!
@edwardcabreramedina7517
6 жыл бұрын
Me ha impresionado ver tu forma de trabajar lo perfecionista que eres un saludo desde España
@maytegarza4608
6 жыл бұрын
Todo bien y perfecto hasta antes de vaciar la mezcla, el acero nunca va hasta la base, debe quedar embebido en el concreto, con ese espesor debe quedar al menos a 25 cms con ayuda de calzas y/o "galletas", ayuda a dar fuerza al concreto y no quebrar al fraguar y luego usó pasta niveladora con exceso de agua, debió usar agua - arena y gruesos- cemento portland en proporciones adecuadas para formar concreto y haber hecho anclaje en paredes para no sobrecargar al piso de abajo si este es entrepaño, creo que lo es ya que tiene madera de baja calidad (aglomerada) pudiendo ser al menos triplay. Creo que va a instalar vitropiso sobre ese "vaciado" ya que le quedó como "firme" base. En fin, aunque la traducción del titulo quedó inadecuada por el traductor automático (por eso creó conflicto en los comentarios) si es criticable. Tiene muy buenas herramientas es indiscutible. Saludos desde México, edo. de Coahuila....Ing. Victor Hugo Jiménez
@rocho58
5 жыл бұрын
Eres un fenómeno, todo un profesional.
@MM2009
5 жыл бұрын
personally I would've lift the mesh of the floor...
@s0012823
4 жыл бұрын
That is critical indeed, now it doesn't have any function. Other point is that the concrete isn't mixed proper. The preparations were great! I guess he was learning as well.. Thanx for the video, I learned a lot!
@metallitech
4 жыл бұрын
@@s0012823 The underside is under tension when load is on top, so I don't think it has no function. That said I would also have lifted it.
@s0012823
4 жыл бұрын
@@metallitech The steel will corrode when it is too close to the bottom. I must be >2-3cm.
@mikejohnson9118
4 жыл бұрын
could have used bits of the mesh to lift it off the floor. Or bent the sides down like feet. Even a .5" would have been better.
@yuriu6708
5 жыл бұрын
Всё отлично но одно зачем он ложил сетку если она снизу стяжки а не в толще.
@user-wx1hz5oq6p
5 жыл бұрын
Сетку правильнее класть вниз.
@AndresLemming
5 жыл бұрын
Сеть не должна быть против пленки, для этой цели есть пластмассовые «туфли», которые увеличивают высоту сетки до 3 см, а от стены должны иметь зазор 2,5-3 см.
@user-qk5jk3uy5c
5 жыл бұрын
Правильно
@sergeygainullin5753
5 жыл бұрын
Да ещё и тонкую. МАК не больше тройки. Надо бы пятёрочку хотя бы, а ячейку можно и десять на десять под такой слой. Ну и ясно, что везде отступ нужен от края, от дна. Возле труб не надо
@user-gu7rh9fc5o
5 жыл бұрын
Зачем стока епкатся налил разгладить и всё делов, кусочек линолеума под угол мебели и всего делов то
@dekonfrost7
6 жыл бұрын
Its good work. I dont know why everyone doesn’t like it. Would have been nice if he had a Fresno trowel to finish off.
@chrisellis7274
6 жыл бұрын
I would hire this guy in an instant.
@jaywilson9182
5 жыл бұрын
I do this kind of work professionally. I would have done it a little differently. But he did do a good job. There had to be a reason why he was raising the floor I am assuming the rest of the floor was getting raised as well
@willybigspuds
4 жыл бұрын
This reminded me of Pingu with the speeded up movements and odd sounds
@elevated8978
5 жыл бұрын
That improvised laser stand is cool.
@specialistscreeding6600
5 жыл бұрын
I don't know where to begin with this, as a screeder this made me weep a little, then piss myself laughing
@markvanderpluijm590
4 жыл бұрын
Amen. There's so many things wrong I don't even know where to start
@ZergRadio
6 жыл бұрын
And after 2 weeks the floor falls through to the apartment below lmao :P
@mr.waffle9736
6 жыл бұрын
why?
@ThisIsSolution
6 жыл бұрын
@@mr.waffle9736 25000000 lbs of mix on a 1/2 plywood subfloor with 2ft on center floor joists
@xelarian289
6 жыл бұрын
Cheapest quality, Just for joke. I think he build for sale, not for his
@retiree1033
6 жыл бұрын
Probably on Beam and Block (look it up) with 100mm closed cell foam insulating layer overlayed with OSB. A common floor system. You'd be surprised how much weight that would support. Don't assume that floor is the same as you'd build.
@ZergRadio
6 жыл бұрын
+Thor The Northern I once saw a very dry piece of turd stranded in the desert, it has absolutely NO sense of humour.
@cristomario9118
6 жыл бұрын
i have seen "professional" doing a crapper job!
@cristomario9118
5 жыл бұрын
...only get "professionals" like you in the US and UK
@alexpsk1784
5 жыл бұрын
Stfu mozzarella head
@cristomario9118
5 жыл бұрын
Alex psk fuck you to you piece of shit!
@Spatzenterror
5 жыл бұрын
@@cristomario9118 this are true german "professionals". btw. great idea but poor details.
@tonyboneize
6 жыл бұрын
Oh he’s good ! Really good! 👍🏻
@thomasschafer7268
4 жыл бұрын
No.never
@ringoglassner7149
5 жыл бұрын
Should the mesh not be more in the middle of the floor levering compound instead of hard down, but other than that he did a good job great work.
@ZingaraJoe
4 жыл бұрын
As steel is great in tension and concrete is good for compression, the mesh would be best raised slightly off the floor on some little chips of stone, cement or 'chairs' so that it has a good protective layer of grout/concrete under the steel mesh to protect from corrosion but well down from the top surface.
@g.mendoza8138
6 жыл бұрын
I don't get the title?!
@kopernickos
6 жыл бұрын
I'm from Poland and i have problem too
@farikomike524
6 жыл бұрын
Nor me.....
@giterdun1864
6 жыл бұрын
5 inches of mud over suspended plywood for no reason.
@tekmusti
6 жыл бұрын
i am turkish even i couldnt get it
@wartoxxxcc1701
6 жыл бұрын
The title is Hungarian but this worker is not sure :)
@valendorn
6 жыл бұрын
так и не понял, почему ванная смущенная))
@Альберт_Кронштейн
6 жыл бұрын
Гуглоперводчик наверное чудит) Хорошо хоть не с китайского переводили)))
@user-wh9oy3hu7v
6 жыл бұрын
Смущенная - потому.что у него штаны постоянно сползают до бикини. :-)
Defo got skills and experience and right tools for the job youve collected over time ace job!
@Stop..carry-on
6 жыл бұрын
No mask mixing
@gabrielgonzales8163
5 жыл бұрын
buenos videos construccion work#1
@ckdigwal3767
5 жыл бұрын
You have the best job work master but please use safety and precaution And use a dust mask. Thank you.
@siviecki
5 жыл бұрын
Jak tak patrzę i se widzę i co se zobaczyłem i co se zrobiłem to ... "wolność Tomku w swoim domku "
@JP-nb7tm
6 жыл бұрын
Give him ten years breathing that dust in and he wont be doing anymore bathrooms
@zoki.to974
5 жыл бұрын
you do realize millions of workers used to work with concrete for hundreds of years without respirators? not for 10 but whole working life, 20-30-40 years...
@MrHBSoftware
5 жыл бұрын
Jp you are good at predicting the future? so what are you doing here?
@rosesousa1245
5 жыл бұрын
Hugo B.
@ravagekillz
5 жыл бұрын
smartboy
@concreteblockmakingmachine4765
5 жыл бұрын
kzitem.info/news/bejne/l4B70oRnpXp9nmk
@allanpkr
6 жыл бұрын
seems a good job except for mix -dont know why it has to be that perfect.its a bathroom????
@keithy363
4 жыл бұрын
allanpkr because if someone comes to my house or works on anything of mine and has that it’ll fucking do attitude they soon get shown the door
@90dfender
5 жыл бұрын
like the knee skateboard, no wonder he can work this fast.
You all in here saying shit instead of giving the man thumb up for a job well done.
@nobodyspecial8127
4 жыл бұрын
Agree this dude is the master
@ninjatato
6 жыл бұрын
Good job man👌👍
@anacristinamarcieldassanto7943
6 жыл бұрын
Kkkkk very good!
@zarkoradovanovic5700
6 жыл бұрын
Prakticna zena
@humleridder7376
4 жыл бұрын
Can i rent this worker, he is so fast😂😂😂
@zuluflight5467
6 жыл бұрын
Auf jeden Fall abonniert. Auch wenn ich es billiger gemacht hätte. So schnell wie der Mann im vid bin ich nicht. Bin Raucher und mache Pausen ; )
@john86779
5 жыл бұрын
he did a great job well done
@timichpyatigorsk9093
6 жыл бұрын
Чето както не очень.
@adangerousidiot
5 жыл бұрын
I agree with grumpy, the guy did a nice job in difficult circumstances. I've been in building trade 40+ years been there many times. Job underpriced just to get the work...All these bullshit videos showing the perfect job, pity the they don't let the viewer know the price
@philipp3771
5 жыл бұрын
This Guy did not a nice Job, sry.... My English is a little bit poor to explain - I´ve seen so many mistakes in this Vid. Many of planning his work, much more of doing it! But his worst Case is the among of water im "Estrichbeton"! Lightconcrete? No Matter, there a lot of concrete-mixes out. After 40+ years, i think U know this. where Do you come from? I´m from germany, we have a rule for every nails, you want to bring in..... We are the founders of clean-diesel ;-)))) Friendly Regards, Philipp
@KugleeKuglee
5 жыл бұрын
@@philipp3771 plan good less work and less error....
@specialistscreeding6600
5 жыл бұрын
You can't scrimp when it comes to floor, it's a very permanent part of the build and this is just unprofessional and shoddy and will cost more money to repair after when it needs latexing
@KugleeKuglee
5 жыл бұрын
@@specialistscreeding6600 Why do you need repair? (Brick/concrete building has this type of floor in Europe and I never heard in my life any repairing about this.)
@specialistscreeding6600
5 жыл бұрын
@@KugleeKuglee if I done a job like this I wouldn't be in business longer than a day. It's terrible, lumpy and needs layering or a tiler wouldn't go near it
@77gravity
5 жыл бұрын
He could have saved a lot of time and effort by putting up the metal strips first, then simply lining up the edge foam strip under it. Instead he measures that line THREE times - lay the foam, trim the foam (no idea why he did that too, instead of just lining up the top edge on the laser line), then the metal strip. Apart from that, he seems to know what he is doing, and his work is very careful and precise, which is good to see (I refer to the carpentry, not the concrete, I don't know concrete).
@sidstewart7399
4 жыл бұрын
Can someone tell me why not just fit timber joists, insulate between and then board. Quarter of the time
@tonyomalley901
6 жыл бұрын
Why raise the floor? He has just created a step up into the bathroom! Why the insulation? it's not needed on a wooden floor! If you have to insulate and screed the floor why not install underfloor heating Rather a pointless vid
@thesunreport
6 жыл бұрын
I'm guessing it's going to be a wet room and there wasn't any room for the drains if the floor wasn't raised??
@nellyishtari
5 жыл бұрын
The whole house is renovated, so all floors will be insulated.... Floor heating in a bathroom isn't necessary, you don't need a permanent heating system, but a fast warm up when you use it. And why insulation? because insulation regulation requires it for eco labels and also if watching other vids, it's an old farm renovated, the floor isn't on crawlspace but directly on ground, which adds thermo leaks.
@dutchymon
5 жыл бұрын
They do not do construction the easy way in Germany, and they don't wear gloves or dust masks either because this would make workers too comfortable.
@augenbutter
5 жыл бұрын
all the rest of the floors will be done, is my guess
@mymorristribe
5 жыл бұрын
Didn't you see the pipes he was trying to cover up that ran on top of the wooden floor. That's why he raised it.
@chiwandos9938
5 жыл бұрын
Не знал, что пленку на утеплитель нужно, я думал, что под него!
@adieslave2218
5 жыл бұрын
Good job ! Very Intelligent !
@mrahim826
4 жыл бұрын
Will the whole house be leveled up this much to match?
@EvntlLPer
6 жыл бұрын
Wer soll den denn bezahlen? max. 1/2 Tag arbeit wurde durch den typen in 1-2 verwandelt, jedes stück styropor nachmessen vorm schneiden? Randdämmstreifen mit Laser abschneiden anstatt hinterher ein mal mit'm Cutter längs zu gehen? WTF
@stefanguido6546
6 жыл бұрын
Vor allem wird der Randstreifen geklebt. Schallbrücken in dieser Größenordnung durch die Tackernadeln , gehen in einem Mehrfamilienhaus never ever.lol.
@michaelazzaro525
6 жыл бұрын
EvntlLPer .
@Lysaner
6 жыл бұрын
Voralm hat er den Randstreifen mit den laser angebracht und mus ihn den noch kürzen omg
@MrFendtfan123
6 жыл бұрын
und zu guter letzt liegt das aks gitter viel zutief, das gehört ins obere drittel.
@estrichligagermanscreed2646
6 жыл бұрын
Ich habe mich köstlich amüsiert wie dieser Unwissender sich abgequält hat. Echt lustig. Der hat fast alles falsch gemacht was man wirklich falsch machen kann.
@pp-jh4ig
6 жыл бұрын
watched 5 minutes trying to figure out what the title means until i realized its auto translated to Hungaryan
@hughpole4259
4 жыл бұрын
even googled it up... well... I'm dumb....
@martinschumacher3252
3 жыл бұрын
noch echtes deutsches Handwerk
@Smitwwwwww
5 жыл бұрын
3:48 что за тачка для коленей?? как правильно называется?? наверное очень удобная вещь!
Пікірлер: 1,1 М.