FluidNC и grblHAL на board: MKS TinyBee V1 corexy
сравнения резки лазера на прошивках FluidNC и grblHAL.
comparison of laser cutting using FluidNC and grblHAL firmware.
github.com/bdr...
github.com/grb...
вот некоторые файлы что вы видели в веб интерфейсе
here are some files that you saw in the web interface
index.html.gz for FluidNC
github.com/mic...
ndex.html.gz for grblHAL
raw.githubuser...
темная темы
dark themes
github.com/jey...
Расширение WebUI v3 - виртуальный джойстик Jog автор
WebUI v3 Extension - Virtual Jog Joystick author
forum.v1e.com/...
github.com/jey...
для компиляции grblHAL eap32 используйте версию не выше этой версии v4.4.8 ESP-IDF
to compile grblHAL eap32 use a version no higher than this version v4.4.8 ESP-IDF
docs.espressif...
прямая ссылка онлайн установщик 4.4.8 ESP-IDF
direct link online installer 4.4.8 ESP-IDF
dl.espressif.c...
устанавливаете v4.4.8 ESP-IDF .после установки включаете Espressif-IDE . соглашаетесь на дальнейшие действия и выходите из Espressif-IDE .
далее открываете ESP-IDF 4.4 PowerShell или ESP-IDF 4.4 CMD и вставляете эту ссылку ка есть .
install v4.4.8 ESP-IDF. After installation, enable Espressif-IDE. agree to further actions and exit Espressif-IDE.
then open ESP-IDF 4.4 PowerShell or ESP-IDF 4.4 CMD and paste this link as is.
#Create directory and clone the ESP32 grblHAL driver into it:
cd C:\
git clone --recursive github.com/grb...
далее переходите в папку с прошивкой и правите только
ESP32\main\boards свою доску .
ESP32\main\grbl\config.h только ставите свою кинематику . вместо off ставите 1
ESP32\main\my_machine.h правите все что нужно вам .
then go to the folder with the firmware and edit only
ESP32\main\boards your board.
ESP32\main\grbl\config.h just set your kinematics. instead of off put 1
ESP32\main\my_machine.h edit everything you need
далее запускаете команду
cd C:/ESP32/ или
cd C:/5/ESP32/
где /5/ это названия вашей папки где лежит ваша поправленная прошивка
далее еще одна команда на выполнения
idf.py build
then run the command
cd C:/ESP32/ or
cd C:/5/ESP32/
where /5/ this is the name of your folder where your corrected firmware is located
then another command to execute
idf.py build
ждете 2-10 мин и в папки build получаете вашу прошивку
в виде
bootloader.bin 0x1000
partition-table.bin 0x8000
grbl.bin 0x10000
далее программой flash_download_tool_3.9.7.exe прошиваете свою доску
программой ioSender.exe настраиваете под себя
wait 2-10 minutes and you will receive your firmware in the build folder
as
bootloader.bin 0x1000
partition-table.bin 0x8000
grbl.bin 0x10000
then use the flash_download_tool_3.9.7.exe program to flash your board
The ioSender.exe program configures it for you
Негізгі бет FluidNC и grblHAL MKS TinyBee сравнения резки лазера.
Пікірлер: 8