Thank you Anthony for posting these videos on the MKS-DLC32 v2.1 board! I am in the process of upgrading my K40 with this board and for me it has been a real slog. I am thinking of using FluidNC and your detailed videos have been very helpful to my understanding of the work that is required. They have given me a much better grasp of the board and FluidNC software.
@LostCloudx4
2 ай бұрын
me too lol. I finally got it moving my K40... now hooked up laser tube and won't fire at all via lightburn :(
@whitneydesignlabs8738
Жыл бұрын
Thanks for the video! I am fully supporting FluidNC, the 6 axis Universal CNC board and Bart Dring's work! Great stuff. Let's help get the DIY CNC community behind this concept.
@rahimelhajdk
Жыл бұрын
I think this is the most helpful video about mks Thanks bro
@peterstrauch3126
5 ай бұрын
Thanks for this great tutorial.
@rics_zip
11 ай бұрын
Will you still make videos of this topic (fluidnc, esp32, mks dlc32 2.1)? I'm new with this too, and this video helps me a lot!
@LeonardoGPate
8 ай бұрын
Hey man, thanks a lot for sharing those videos! I am trying to run a core XY pen plotter with 2 TMC2209 and a MKS dlc32 2.1 but I am having some trouble with the servo to lift the pen up and down. In the examples configurations file I couldn't figure out how to make a propper config.
@kyon_03
11 ай бұрын
Nice just ordered this board for laser engraver
@arinurcahyo
Жыл бұрын
Hi, Nice video and well explained. I bought this board recently too with the same version. btw, what advantages of fluidNC over MKS default firmware?
@brakthehun
Жыл бұрын
For What I was doing,, I needed 2 y motors with 2 endstops (one on each side) along with an X-axis and it's own endstop. I also have a polarbear CNC which I modified and I use fluid NC's custom buttons to focus and draw.
@doug3458
Жыл бұрын
I've discovered that the ESP32 only needs pin 0 to be grounded the first time it is programmed, thereafter it can be programmed without grounding.
@avexoidavex3577
Жыл бұрын
Hi Anthony! Please tell me, what exactly makes FluidNC better for CNC than the default firmware? I want to build a small CNC milling machine for a hobby, and am wondering if I should reinstall the board firmware.
@brakthehun
Жыл бұрын
There are pros and cons. FluidNC has much more functionality but default MKS supports a screen.
@peterbardos7396
Жыл бұрын
A nice video. Can you tell me which board you used? The MKS DLC32 version 2.0 or 2.1? I can not see it in the video.
@brakthehun
Жыл бұрын
2.1
@beykana
Жыл бұрын
Hello, I have the same card. The Z axis is off and I can't move the motor. When I try to update the software to solve the problem, it does not see the card. Any idea how to fix the problem?
@JeffCanada-fh7dt
Жыл бұрын
Are this board conpatible with ortur laser master 2??
@Schraubfreak
Жыл бұрын
Good video thank's for it. It's possible to get the Display to work?
@DanielRodriguez-cm6mh
6 ай бұрын
I have gone from standard grbl to fluid nc but I notice a change in the management of laser power... for engraving on methacrylate I previously used 200mm/sec 20 power and now I have to use only 5 power because with 20 it perforates the material, It seems to me that power management is not delicate... Can someone tell me how to solve this please.
@jamescullins2709
Жыл бұрын
How hard would it be to use external stepper drives like Geckos?
@brakthehun
Жыл бұрын
From what I've seen of the Gecko drivers,, fluidNC should work fine.
@giova2927
Жыл бұрын
Hi Could you help me monitoring a cnc using fluidNC?
@loiphongngo135
Жыл бұрын
😍
@shaneschuller2513
6 ай бұрын
Could this work for Plasma CNC table?
@MrRysiek139
Жыл бұрын
Mam problemy plik.yaml otwiera się jako plik tekstowy nie umiem wgrać wykasowane mam wszystko co robić jak zmienić
@xConundrumx
7 ай бұрын
Yeah the screen thing is not FluidNC's fault. The MakerBase TFT is not open to customization as they don't provide access to the tools to 'reprogram' the firmware on that screen. I know, I asked a few years back.
@kifahzaidan4505
Жыл бұрын
Hi, Thanks a lot, its really greate effort and great knowledge. i need to do a project for a preset position linear actuator with a DC motor abd a stepper motor, with Arduino Mega or UNO but i am not able to write the code and the scheme, can you please help. Regards
@francescofranceschini2258
Жыл бұрын
È possibile usarla su cnc 3018 con fresa è non con il laser
@nature4925
Жыл бұрын
Hi I am Taljit Singh, from India... I am developing CNC router 8*4 feet bed size..... Earlier I opted. Arduino uno & GRBL sheild as controller But now I go for MKS DLC 32v2...board, I flashes Fluid NC in board as you showed ( follow your instructions) but I had one problem, when I connect my limit switches to board, it disconnect automatically..... And COM not find the connection.... Can you suggest me the solution. Thanks
@brakthehun
Жыл бұрын
Check your limit switch wiring. Chances are you're grounding out the 5v and browning out the board.
@joseluisnavarrete3426
Жыл бұрын
The s is for step, because stepper motor xD
@nuxrohox-cortx-6222
Жыл бұрын
nema motor tipe?
@brakthehun
Жыл бұрын
Nema17 84oz (steppers online) EBAY
@angeloctaviocruzmartinez345
Жыл бұрын
DISPLAY COMPATIBILITY ???
@grahamstewart79
Жыл бұрын
basic i2c display support was recently added to the latest release of fluidnc
@zakariakhamees
Жыл бұрын
Can it run grblHAL?
@brakthehun
Жыл бұрын
Sorta... grblHAL is outdated at this point. It does support ESP32GRBL.
Пікірлер: 38