Excellent presentation - no beating around the bush. Also very useful for Volvo C30/S40/V50 (T5 versions anyhow) which are almost exactly the same
@erwinroman4217
5 жыл бұрын
Thanks for the vid. There's very little information on the Volvo C70 T5 Hard top convertible which has the same engine. A B5254T. Replacing the radiator hoses on my daughter's C70 and the airbox removal was a mystery. I also removed the battery, battery tray to gain better access. This is our 5th and possibly last Volvo unless I find a super clean 240. Had 745T, 945T, 855T, now a V70 3.2 and the C70T5. Just did T-belt last week. The Ford vids are helpful.
@alancooper7062
4 жыл бұрын
Thanks for info, i managed to drop a torx bit while changing spark plugs and couldnt see it,, hadnt a clue how to get airbox off, with your instructions i was able to remove it easily and find part, cheers
@paulsoames7980
2 ай бұрын
Mine is having none of it
@TunedVXR
5 жыл бұрын
When you fit air filter where does the ecu go ? And will I have any trouble with ECU after unplugging it should I disconnect battery ?
@johnson1607
4 жыл бұрын
did u manage to find out what to do?
@OEMDeniedPerformance
3 жыл бұрын
Apologies - totally missed you question. When installing an aftermarket intake the ECU should be mounted in an RS mk2 ECU enclosure. You will cause no problems disconnecting the ECU or battery - the only way to lose data from the ECU is via programming (or damaging ECU by dropping it/shorting it out on a power source)
@swagdog8639
3 жыл бұрын
Is this the same process for a mondeo?
@OEMDeniedPerformance
3 жыл бұрын
pretty much, have a bit more space in a Mondeo so its slightly easier
@petert696
3 жыл бұрын
@@OEMDeniedPerformance how do I remove the air inlet pipe from the air box on my Mondeo xr5, as it's on the opposite side to the focus. Theres no obvious way to remove it apart from force, but I dont want to snap it. Im trying to get to the starter motor so I can lock the crank and do the timing belt.Please advise.Great video by the way.Thanks
@OEMDeniedPerformance
3 жыл бұрын
@@petert696 airbox feed pipe on the mondeo is on the passenger side, pull it away from the airbox and itl unclip from it. Then you will be able to remove the airbox and leave the air feed still attached to the car
@rikkietan8789
6 жыл бұрын
Hi guys is it necessary to disconnect battery when unplugging ecu
@OEMDeniedPerformance
5 жыл бұрын
You should always disconnect battery before unplugging any module in a vehicle.
@robertacanning1977
11 ай бұрын
Yes if your ecu touches the starter motor if the battery is still live then boom goes your ecu , people put a towel over the starter motor to stop this if they don't unplug battery , just a tip 👍
@djlogic83
2 жыл бұрын
Awesome video mate it helped me out loads.
@mixtapeculture4531
5 жыл бұрын
Question...the electrical socket that's in between the engine cover and the air flow pipe, its got like a grey clip thing. Whats is it for?
@OEMDeniedPerformance
5 жыл бұрын
That is the o2/lambda sensor in the downpipe. ECU uses this to measure air fuel ratio in the exhaust
@cambridgembelengwa3674
5 жыл бұрын
Hi I'm having difficulties on removing my injector rail. does anyone have a video on it?
@OEMDeniedPerformance
5 жыл бұрын
Take the upper inlet manifold off (6x8mm bolt from underneath, vac line from the CBV on left hand side, just behind the throttle body, line from underside to the left of the oil filter housing, brake vac line on the right hand side) Then remove the 2 x 8mm bolts holding the fuel rail down to the lowr inlet manifold and remove the torx screw holding the fuel line to the rail and wiggle the whole rail upwards
@Hodgmeisterpro0209
Жыл бұрын
I can’t manage to unplug the connectors on the ECU. No idea how to get them off. Any help would be massively appreciated!
@OEMDeniedPerformance
Жыл бұрын
need to lift up the red retainer and then connector will undo itself
@Hodgmeisterpro0209
Жыл бұрын
@@OEMDeniedPerformance it turned out there was an anti tamper guard on it which was stopping me getting to the red levers. Nightmare
@OEMDeniedPerformance
Жыл бұрын
@@Hodgmeisterpro0209 thats very unusual unless vehicles an RS as they had them from factory but the STs normally didnt. We talking about the light gold coloured one with the snap off headed bolt?
@Hodgmeisterpro0209
Жыл бұрын
@@OEMDeniedPerformance yeah that’s right. After doing a bit of research, it seems as tho some later ST models had them on. I managed to get it off without damaging the levers but it wasn’t easy. In the end I did it all for nothing as the ECU cables wouldn’t reach the ECU in its new holder, so ended up putting it back to standard. The cables were pulled tight and putting pressure on one of the radiator hoses, so I’m gonna have to rethink that.
@user-uf6gc1nd7e
Жыл бұрын
@@Hodgmeisterpro0209 look for group a install vid by bd performance on KZitem, Im sure he cuts the plastic cover on the wires...that may free up some slack to give u abit more wiring play
@BlackMetalRC85
7 жыл бұрын
nice!!!
@stylo8133
3 жыл бұрын
I have a question. When replacing with new throttlebody. Do is need new software or is the throttlebody self learning?
@OEMDeniedPerformance
3 жыл бұрын
No programming needed mate. Only things you ever have to program on these vehicles is modules if they get replaced. Throttle body failure is rare though, usually throttle DTCs are caused by instrument cluster faults. What DTCs are you getting?
@stylo8133
3 жыл бұрын
@@OEMDeniedPerformance Hi I have p2502 charging system voltage. What does ie mean. Have a new battery and the alternator looks new to me.
@OEMDeniedPerformance
3 жыл бұрын
@@stylo8133 Check alternator output with a multi meter at the alternator itself then at the battery. You may have blown the maxi fuse from alternator to the battery is best guess without seeing the vehicle
@stylo8133
3 жыл бұрын
@@OEMDeniedPerformance Thanks. Where is this maxifuse located?
@OEMDeniedPerformance
3 жыл бұрын
@@stylo8133 Just off the left hand positive battery lead. Test for voltage each side of it
@markpadwick6101
7 жыл бұрын
hi guys im struggling to take ecu cables off any ideas ?
@OEMDeniedPerformance
7 жыл бұрын
if you look closely at the connectors there is a little tab that says press, press it in then flip the switch part and the connector will unplug as you lift the switch
Пікірлер: 41