This video will describe materials you can use to build your own pressure/force sensors. A microcontroller interface using an Arduino Nano will be covered. BC Robotics: www.bc-robotic...
That was really interesting, and lots of ideas had spawned in my head already. Thanks for your videos, they're to the point, no flashing intros and sponsorships. It's refreshing, among all the paid channels.
@0033mer
4 жыл бұрын
You're welcome!
@prtcgv5105
4 жыл бұрын
Sir... you're as straight as an arrow!!! I'm trying to develop a sensor that can be buried into the ground and installed, say every 50 feet, in order to detect intruders jumping a 6ft fence into my property (a typical problem in Brazil). Until I stumbled upon your channel I had no idea that there are so many choices out there! We all appreciate you sharing your expertise!!! ;)
@0033mer
4 жыл бұрын
Thanks for the feedback. Glad I could help.
@PhG1961
4 жыл бұрын
Well done ! This might be a good solution for sensing fingertops for robots.
@Asyss_Complex
4 жыл бұрын
Thanks for the tips. The applications are countless!
@0033mer
4 жыл бұрын
You're welcome!
@tomaszwota1465
4 жыл бұрын
This is interesting. Plenty of ideas could be realized with this, from simple switches to pressure sensitive skin-like arrays. I guess you could make a crude force sensitive touchpad out of an array, or maybe out of two electrically separated layers of intersecting "lines" and "rows". You could have the position data as well as the pressure data. You could use some of this in electronic piano keyboard for adding per-key vibrato ability, not to mention keystroke force. Although, wear-resistance would have to be taken into account when choosing the material used. Our maybe sending pressure on a usb computer keyboard, turning some of the keys into kind of analog inputs. I guess all kinds of analog momentary inputs could be done this way if precision wasn't important.
@M0XYM
4 жыл бұрын
appreciated - good to see Forth being used.
@_Error_404_Goodbye
Жыл бұрын
I’d love to see you do a video specifically measuring impact force, say up to 10lbs max, with a value readout on a display. I’ve looked everywhere on KZitem and some only touch on impact as an example, but none really show anything dedicated to it even though it’s an extremely useful metric to measure. Very cool videos 👍🏼
@0033mer
Жыл бұрын
You can measure impact using an accelerometer and calculate the force applied: kzitem.info/news/bejne/z3qj0qd-fKdzn34 To get a force reading directly in LBS you could use a load cell strain gauge. The force can be applied to a cantilever beam where the fulcrum can be adjusted to match the max rating of the load cell. kzitem.info/news/bejne/lIKlvKCVqpyWhWk
@_Error_404_Goodbye
Жыл бұрын
The reason I was saying using a method like this to measure the impact is because it would be interesting to apply that to the force of a trigger hammer striking a firing pin to see the max force of the impact. This metric can be useful in diagnostics of light primer strikes and to also compare different weight fire control group springs and to compare between brands and styles of fire control groups. I know this seems specific to one application, just a project idea I’ve been throwing around in my head for a while which is what lead me to this video to begin with lol. Just a little light reading lol
@malgailany
4 жыл бұрын
Very nice Ideas. However, these sensors have nonlinear behavior and they are great as switches. It's interesting to see some linear sensors that provide a proportional output to the applied force. Thanks.
@klave8511
4 жыл бұрын
Mohammed Algailani : Piezoelectric materials are linear. Their parameters are well defined for the many types of piezoelectric materials. The charge or voltage constants tell you the charge or voltage generated per unit force or pressure. I don’t recall the other sensors but if they’re non linear then the micro can work it out for you, worse case would be a lookup table.
@TheTubejunky
4 жыл бұрын
Very well put together! Great informative video sir!
@0033mer
4 жыл бұрын
Thanks for the feedback.
@lavkushchaudhary6981
Жыл бұрын
Thanks for the information you saved my project.
@0033mer
Жыл бұрын
You are welcome! Glad it was helpful.
@rodneyjaygarrett
4 жыл бұрын
Very nice video. Great ideas. I really enjoy your videos. I hope you keep making them!
@0033mer
4 жыл бұрын
Thanks for the feedback!
@deltaexile1906
3 жыл бұрын
Short video but very useful! Thank you so much
@0033mer
3 жыл бұрын
You're welcome!
@bobvincent5921
4 жыл бұрын
Thanks, I have a nano and with practice it can be programmed to assimilate many things.
@unomasenelmar
4 жыл бұрын
Super explication!, de luxe, thanks!
@0033mer
4 жыл бұрын
Thanks for the feedback.
@MrDereckb2
4 ай бұрын
For the foam and film sensors. Is there a way to have it only react to something that’s like 300 lbs of pressure and up? Basically ignoring human input.
@francescomist3050
2 жыл бұрын
Thanks for sharing , very nice video
@0033mer
2 жыл бұрын
Thanks for visiting
@ShockDiamonds
5 ай бұрын
Squirrels hate these things! However the birds couldn't be happier.
@excrubulent
2 ай бұрын
This is a great overview, thanks! Yet more evidence for me that the standard way to use velostat is sandwiched between conductors, and not used to bridge across two conductors like the first example I saw. Also, I'm curious, do piezo sensors detect force, or do they detect percussion? My understanding is that they don't work very consistently to measure static force. Is that right?
@0033mer
2 ай бұрын
Here is another video using velostat as a pressure sensor: kzitem.info/news/bejne/1JuDvJuAbWNzjaw Yes, Piezo sensors basically detect percussion. They output during acceleration and not during static pressure. A good example of that is an engine knock sensor. kzitem.info/news/bejne/x5B9u66hZnSKmoY To measure static force use a strain gauge (load cell). kzitem.info/news/bejne/lIKlvKCVqpyWhWk
@excrubulent
2 ай бұрын
@@0033mer Thanks for the answer! Yes, I've used knock sensors for a digital drum before, and I just wanted to check I had the right info. I'm now making MIDI pads that need static force sensitivity for sustain, so velostat is definitely the way to go from what I've seen.
@keithcitizen4855
4 жыл бұрын
I saw an ingenious pneumatic player piano roll motor control circuit incorporating a piezo activated by air pressure
@WalidIssa
4 жыл бұрын
Great
@user-bb8fo6gb9e
3 жыл бұрын
اهلا استاذ وليد ما توقعت احصلك هنا لكن قاعد احاول صنع مثل هذا المشروع
@murrrr8288
3 жыл бұрын
great video!!!!
@0033mer
3 жыл бұрын
Glad you liked it!!
@murrrr8288
3 жыл бұрын
@0033mer I gotta try that foam. I saw video where someone was using VHS tape as variable ribbon resistor, i think i'll try that with C-cassette as well :)
@marsiooisram4694
3 жыл бұрын
Any idea on how to build a momentary expression pedal for guitar effects with these sensors?
@Dr.SanjeevSaxena
4 жыл бұрын
Great. Thanks for sharing the fantastic information. I want to build my own bite force sensor & bent-pressure sensor for generating sound frequencies for a midi player... Can the conductive foam be used.... Can you share more technical details about how to do it.... and from where we can get free source material? Kindly help... 🙏🏻🙏🏻🙏🏻
@mcon1982
3 жыл бұрын
I'm looking to build golf targets using pressure sensors so when hit they light up LED's, can you help?
@mehmetkurga8850
3 жыл бұрын
Thank you.
@0033mer
3 жыл бұрын
You're welcome!
@ThinhNguyen-jw9dk
2 жыл бұрын
What a helpful video! Can I have a question? Should i buy a 1mm and pile it up or 3mm piece of antistatic sponge? (1mm is half the price of 3mm). Thanks.
@0033mer
2 жыл бұрын
The foam is conductive so you can layer them.
@kashv1793
3 жыл бұрын
Can a force sensitive resistor be made from antistatic mat?
@0raibi
3 жыл бұрын
As you have tried them all, if I'd like to use something to measure the pressure in several points to distribute the weight right in the centre, will this be the right option to measure the different readings from different points and prompt the user to redistribute the weight?
@ahmetanbar6346
4 жыл бұрын
could we increase the range of the sensor from 10 kg to 100 kg by putting a layer top of the sensor?
@klave8511
4 жыл бұрын
Those films look interesting, I imagine an array could be used to make a touch sensitive “skin”. Is it possible to use an array of contact points like a keyboard matrix to get local pressures or will the film spread the electrical signal across its surface if it’s not cut into disconnected sections?
@0033mer
4 жыл бұрын
Yes .. check online, there are others who have built an array of contact points using Velostat.
@internetuser8922
3 жыл бұрын
From a cost/feasibility standpoint, what do you think would be ideal for something like a pressure-sensing skateboard ramp, or dance floor or something? I like the foam idea, I didn't know about that one.
@0033mer
3 жыл бұрын
I have introduced a few options so it depends how you implement them as far as cost goes. Velostat would be something to look into for large projects.
@ginagavino7752
Жыл бұрын
Hi! Our company is using FSR for our acoustic synthesizer and with some of our assemblies with our device, we're experiencing that the FSRs are being compressed. The sound keeps going even not putting pressure on it. How this will be avoided? Thank you.
@0033mer
Жыл бұрын
Yes, that is called loading hysteresis. Keep the compression duration time to a minimum and avoid heavy pressure together with proper software to avoid this problem. Check the data sheet for loading hysteresis specs.
@ginagavino7752
Жыл бұрын
@@0033mer Thank you for your response.
@ginagavino7752
Жыл бұрын
@@0033mer We need to apply glue on the FSR to place it on our device. Is this advisable? If so, what's the best kind of glue that we can apply to hold it permanently in place? FSR is a crucial part in manufacturing our acoustic synthesizer, which until now, we're still finding out how to optimize its use and avoid issues. Thanks again.
@0033mer
Жыл бұрын
Use a 3M adhesive like their 3M 467MP Transfer Tape. Follow their instructions on how to apply the tape.
@ginagavino7752
Жыл бұрын
@@0033mer , I'm wondering if you have another platform where I can ask few more questions regarding FSR. I want to send photo regarding the assembly that I'm doing and maybe you might give suggestions of the proper way to adhere FSR or recommendations that I can apply into it. Thank you.
@kryptocat4240
4 жыл бұрын
Wow
@unknownblueblue
3 жыл бұрын
man thank you very much
@0033mer
3 жыл бұрын
You're welcome!
@kevinjovanov1083
2 жыл бұрын
Are your able to make the outlet a value on an lcd screen vs the 4 LED lights? Thanks
@0033mer
2 жыл бұрын
Yes, you can scale the ADC output values to your desired range and feed them to a LCD display.
@simplelyf4072
4 жыл бұрын
Why do u form a voltage divider to feed into the microcontroller? Sorry I have an idea why but can you please explain?
@0033mer
4 жыл бұрын
To convert the changing resistance of the pressure sensor to a changing voltage that the ADC of the microcontroller wants to see, you would use a voltage divider. Check out this video: kzitem.info/news/bejne/04qFmYljaYCbp6w
@vikramsinghrajput4679
4 жыл бұрын
What is the resistor value used as voltage divider in the circuit of electrostatic foam at 2.53?
@0033mer
4 жыл бұрын
Every setup will be different but I used 47K.
@puneetjain5625
3 жыл бұрын
Gold.
@gauthams1291
3 жыл бұрын
Thanks man👍👍✌️✌️
@0033mer
3 жыл бұрын
Your welcome.
@sidharthap
4 жыл бұрын
what's the part numbers for those beautiful white LEDs?
@0033mer
4 жыл бұрын
Check out Dipmicro. www.dipmicro.com/store/LED3W
@aakashdewangan7313
2 жыл бұрын
Can I use piezo force sensors you have shown, for dynamic force measurement with high accuracy? Please reply
@0033mer
2 жыл бұрын
If you need accuracy then you should consider a strain gauge or load cell. kzitem.info/news/bejne/16x_y2R4f3SdeX4
@orebelo
2 жыл бұрын
@0033mer Very interesting and useful video. I'm planning to do a DIY MIDI controller and put a sensor and I have no experience with those components, May I ask you the order of precision and/or reliability of each kind of sensor?
@0033mer
2 жыл бұрын
FSRs are the easiest to interface to electronic circuits for trigger applications. kzitem.info/news/bejne/1mh7rnivq4iQeWU
@rynemascarenhas175
4 жыл бұрын
Can I have your circuit diagram for the antistatic foam sensor... And can you please tell me exactly where can find the antistatic foam?
@0033mer
4 жыл бұрын
Most electronics supply stores will stock anti static foam. www.jameco.com/z/HDBC-1206-25-12-x-6-Conductive-Anti-Static-Foam_2237896.html A resistor and the static foam form a voltage divider feeding the ADC of the Nano. kzitem.info/news/bejne/2HunzHylmJmmem0
@rynemascarenhas175
4 жыл бұрын
@@0033mer in this video u used a resistor as a voltage divider of how many ohms?
@rynemascarenhas175
4 жыл бұрын
@@0033mer as I am not getting the same output as you are getting.. I am getting values between 920 to 970 only..
@0033mer
4 жыл бұрын
@@rynemascarenhas175 Ohmmeter the setup and calculate a resistor to give you a good range. You can also use a potentiometer and adjust for best results. I used 47K in my divider.
@therianet
4 жыл бұрын
charge pump for piezo ? the circuit looks like common emitter amplifier
@0033mer
4 жыл бұрын
The transistor is a MOSFET which is driven by a charge pump. It drives the GPIO input pin on the microcontroller when the Piezo is triggered.
@therianet
4 жыл бұрын
@@0033mer Im still not getting it, did MOSFET required higher supply voltage or negative voltage?
@0033mer
4 жыл бұрын
The MOSFET is a N-channel VN10KM which has a threshold gate/source voltage of 1.2 volts. The pullup resistor is connected from the drain to the 5 volt supply. When the piezo is triggered a positive DC voltage is applied to the gate turning on the MOSFET and driving the GPIO on the Nano.
@therianet
4 жыл бұрын
@@0033mer so it is just a high impedance input buffer amp, was wondering why charge pump(dc-dc voltage converter) is mentioned.
@0033mer
4 жыл бұрын
Yes ... it is a high impedance input buffer that will not load down the (ac-dc) charge pump. The output of the piezo sensor is ac.
@Montsalvatsche
3 жыл бұрын
so I use these things for midi applications and you basically just told me that a 12 dollar part comes free with my mobo in quantity so long as I buy the wicking which I already have lol
@ashwin372
Жыл бұрын
why not stick the velostat insted of just placing it as a sandwich
@Edmorbus
4 жыл бұрын
interesting
@lelotortelli
2 жыл бұрын
Hey. I’m looking for a paid freelancer to design and build a prototype similar to some of your projects above. Could you share a contact?!
@0033mer
2 жыл бұрын
Look for a local product develop company in your area. Here is an example of one in my area. www.klnklein.com/
@iforce2d
2 жыл бұрын
4:52 stop doing that you big meanie. It clearly doesn't like being squeezed !
@0033mer
2 жыл бұрын
That was laughter!
@dukejivetalker7541
8 ай бұрын
Ive been tthinking about punch force sensor device for boxing training. Any advice?
@0033mer
8 ай бұрын
Have a look at accelerometers or Piezo sensors. Check out these videos. kzitem.info/news/bejne/z3qj0qd-fKdzn34 kzitem.info/news/bejne/x5B9u66hZnSKmoY
Пікірлер: 99