Thank you for explaining how to properly line up the timing dots on the two gears. No one else is explaining in completely or as well as you.
@EricsEverythingAuto
11 күн бұрын
@danielragsdale4825 your very welcome I'm hoping to get more videos out soon. The shop has been going through some crazy expansion so I haven't been posting. Soon though we will be running videos full time
@coreybrenner
2 ай бұрын
Thanks for telling us the size and thread pitch for the cam. That helps, and now my wife can pick up the needed supplies in town. ❤
@EricsEverythingAuto
2 ай бұрын
Your welcome. This job takes a little time but with just a little knowledge it makes it alot easier
@marcos.lombardo
Жыл бұрын
hey, thank you, fwiw, if the distributor doesn't spin, it could still be a distributor failure - which just happened to me, which i determined by pulling it out - it was in two pieces. timing gears good! but thanks for the vid!
@EricsEverythingAuto
10 ай бұрын
Yes you are correct I did not mention that point in the video but the last owner already replaced the distributor on this vehicle so that had already been ruled out. But excellent point
@nathandevine552
29 күн бұрын
Yup had a roll pin break on me once
@troydrennen4690
2 ай бұрын
Very helpful video thanks
@EricsEverythingAuto
2 ай бұрын
Your welcome
@EricsEverythingAuto
2 ай бұрын
Thanks for watching
@vibeandride2984
Жыл бұрын
This helps a lot thank man thanks
@EricsEverythingAuto
Жыл бұрын
your very welcome. i could not find the right video that shoed the whole job so i hope this makes it easier for everyone.
@vibeandride2984
Жыл бұрын
@@EricsEverythingAuto it really does
@sqlabs8821
9 ай бұрын
Or just look down the oil fill, valves arnt moving? Gears.
@EricsEverythingAuto
9 ай бұрын
Very true
@RonaldLewis-py6yt
5 ай бұрын
Thanks for sharing, I have a 95 f150 4.9 the distributor roll pen broke causing a no fire ,question is i pushed the gear back on by hand appears i just need a roll pen But I believe the gear should have to be pressed on i don't think the roll pen will hold,thinking i need to replace the distributor, your input would help! Thanks again 😊😊
@EricsEverythingAuto
5 ай бұрын
Yes that is also a no spin condition but we had already checked that off because the last owner had already replaced the distributor and old one was on floor in truck. Thank you for watching . I appreciate all the likes and comments
@RonaldLewis-py6yt
5 ай бұрын
Actually you don't understand my question, the roll pen was broken causing timing to jump I'm saying I need to replace my distributor, I have a new one on order, Thanks 😊
@EricsEverythingAuto
5 ай бұрын
@@RonaldLewis-py6yt that should get you fixed right up. I would just replace the whole distributor to keep from having future problems
@RonaldLewis-py6yt
4 ай бұрын
I believe the timing gear is defective it broke down, I'm fixing to get it torn down!!
@EricsEverythingAuto
3 ай бұрын
@@RonaldLewis-py6yt it is very common
@jackwells1452
10 ай бұрын
Did the steel gears make noise, I replaced a set and now I have gear noise
@EricsEverythingAuto
10 ай бұрын
We do not have any noise issues with these gears
@jackwells1452
10 ай бұрын
@@EricsEverythingAuto the set I did sounds like a supercharger, I read a few threads that said they had the same experience
@EricsEverythingAuto
9 ай бұрын
I havent heard any complaints but, This old tuck is just used around the farm they wouldn't notice if it made noise anyhow
@nathandevine552
29 күн бұрын
Yup they will that's why the factory gear is plastic
@jackwells1452
29 күн бұрын
@@nathandevine552 well ended up putting an aluminum top gear in and no more noise
@WillisBullabough-mh9wb
6 ай бұрын
Ok so im doing the same thing to my 93 ford f150 the timing gear pulling busted trying to remove it but my marks on crankshaft are not at 12 o,clock more like 6 so my question is can i turn the motor over by hand to line my marks up or what should it do someone told me to take manfold off and and the push rod cover off just to play it safe about the push rods dont get bent idk so comfused about this
@EricsEverythingAuto
6 ай бұрын
Yes absolutely can turn by hand don't force it. Should turn nice and easy
@victorwood5430
4 ай бұрын
What was the number for the time gear I might need to replace one I just want to know where I can get that from
@EricsEverythingAuto
4 ай бұрын
The cloyes number on the gear set is 2766s. I purchased it at fisher auto parts for $78
@BoringFisherman
Жыл бұрын
The aluminum gear doesn't throw off the knock sensor?
@EricsEverythingAuto
Жыл бұрын
It is steel
@JimTurnerGenuine
5 ай бұрын
Did you pull the oil pan to see if it had chunks of gear teeth in it?
@EricsEverythingAuto
5 ай бұрын
Yes we did oil pan as well
@kerrykurschinsky2451
Жыл бұрын
THIS PART DIDN'T GET VIDEO,.... DAMM BUDDY,.... WHY DO YOU THINK WE WANTED TO SEE HOW.... TO TAKE THE GEAR OFF,.........WHAT A WASTE OF TIME........
@Charles-vc3rm
Жыл бұрын
Take a drill and drill three holes in a triangle pattern on the gear as close to the center as possible (make sure ur puller will still fit as well) and tap threads for 5/16 bolts, then bolt the puller on, it should come right off, mine did anyway
@EricsEverythingAuto
10 ай бұрын
No it did not but if you listen I explain in detail how I did it
@stu3131
Жыл бұрын
Great tutorial.
@EricsEverythingAuto
Жыл бұрын
Thank you. this old girl runs great now.
@stu3131
Жыл бұрын
@@EricsEverythingAuto Hoping for the same for mine!
@EricsEverythingAuto
Жыл бұрын
@@stu3131 good luck let me know if you have any questions
@mikemoore279
4 күн бұрын
I needed to c how to remove both gears you skipped right thru them you were more concerned with piecing the old nylon gear back together
@EricsEverythingAuto
2 күн бұрын
@mikemoore279 listen to what I said. I explain how it's done.
Пікірлер: 47