I got same noise problem now on a 2017 ford f350 6.7 turbo diesel and this just helped me out and THANK YOU for this video 💪🥇
@Thedoug369
Жыл бұрын
RIP Ron, you the man 🙏
@DieselTechRon
10 жыл бұрын
Technology changes. The old diesels were big loud lumbering work horses that would last and could take neglect. But they stunk and were only for the true working class that needed them.. The new stuff is fast, quiet and efficient. With that comes more components and electronics. There are also regulations and contracts with builders and suppliers. Design conflicts and learning. It's getting better by the year and with a little education and love they will last.
@agustinvilla5472
6 жыл бұрын
DieselTechRon I have 6.4 it's making louder popping sound but from top left pass intercooler hose any info would be appreciated thanks
@jeffanderson7256
5 жыл бұрын
Agustin Villa bro he had already passed away when you posted your question
@briansmobile1
8 жыл бұрын
Great video Ron! I'm doing this same repair right now. had a yellow clip fall out and the truck wouldn't pop, but it would start quiet and then develop a rattle/knock when it got up to temp. The long rocker arm was worn on the inside and the bridge was worn forward of center. Main turbo oil drain was leaking pretty bad too.
@unencumbered
7 жыл бұрын
briansmobile1 Going to start this repair Tuesday morning...driver side. If you're available for any thoughts...thanks
@stevehustler1baird320
10 жыл бұрын
Newer diesels run a higher oil pressure than the older models. But people do not read the manual and do the maintenance properly, which leads to this problem described here. Thanx Ron 4 this info, hopefully it will help many.
@TheTexastngray
8 жыл бұрын
My 2010 6.4 just developed this noise about a couple of weeks ago and couldn't figure out what it was. I'm sure glad you had this video lol
@crystalbuskirk11
10 жыл бұрын
Thanks Ron, great information!! I owned a f250 with a 7.3 and have never been happy with the 6.4,,,,
@mikebrennan4534
7 жыл бұрын
RIP sir.....RIP
@Thebipolarachiever
6 ай бұрын
Rest in peace Ron! We miss you
@mrfanman2u
10 жыл бұрын
Hello Ron, I do performance work and have built a few 6.4L, but don't do a lot of diagnostic type repairs I mostly do the 550-600hp tuner, emissions delete, and they blew the heads off of it type repairs. On a few occasions, I have ran across trucks that make a "bloop" noise, just once, very similar to this on start up, before the engine actually fires.
@woodsga
10 жыл бұрын
How does someone know if they have the latest calibration?
@francissullivan6400
4 жыл бұрын
Let's use plastic keepers...WHAT COULD GO WRONG??
@galesams4205
5 ай бұрын
All these small diesel engines are MONEY PITS.
@DieselTechRon
10 жыл бұрын
Yes a 6.0 will do this but 60s are normally a broken lifter.
@stevecox5219
10 жыл бұрын
Thanks for your reply.
@devonmiller2232
5 жыл бұрын
How much was it to do this?? My 6.4 is currently doing this, has been for a few months
@mrfanman2u
10 жыл бұрын
One more thing... We have a 6.4L truck in the shop now that, came in for a messed up turbo VGT, and has wound up having a longblock with labor on our dime. I did not work on it personally, so I am going from what I was told and what I saw as the truck progressed. I would have taken a different course of actions, but I wanted to share. Truck is a deleted 09', with a Spartan tuner. It came in, we fixed the turbo problem by replacing the one turbo, after replacing the turbo and changing the oil, the truck would not start, wasn't making fuel pressure took it back apart and found the wiring harness that goes under the turbos for the HPFP chafed, put a harness on it and it fired right up. Drove it for 20-30 miles and it suddenly shut off and would not start, no HPF.. put a pump on it and as soon as it started it had a hard miss on #3 that did not go away. Replaced the injector and it ran well for 2-3 miles and started loping at idle, like a sticking IPR on a 7.3/6.0, but ran perfect everywhere else. Took it to Rudy's to update the Spartan hoping that the tune had become corrupted by the IDS.. Updated... ran perfect, for about 5 minutes, then it shut off again, with no HPF yet again. Towed it back to the shop and put a second pump on it. Oil was checked before it was driven (I checked it myself). It starts up and runs perfect. Backed out of the shop, and driven 2 more miles and suddenly it starts billowing out white smoke like crazy. The truck was turned around and driven back to the shop, still billowing smoke, barely running, and rattling. Shut the truck off and hooked up IDS and tried to restart and the engine hydrolocked. On teardown... discovered 9 gallons of fuel/oil mix in crankcase, a broken exhaust valve on #5 (A small chunk out of it... thinking back, this is probably what buggered up the VGT) All 8 cylinders were completely full of fuel, as was the intake, and dripping out of the exhaust. #8's rod was bent into the crankshaft. At this point we are like "WTF". What on earth caused it???
@DieselTechRon
10 жыл бұрын
The VGT actuator is on the same circuit as the pump. I have a video showing to look for movement and how that gasket is usually bad if it does not move. With that much fuel in the oil, you either had a pump or injector leaking internally. I monitor short fuel trims to try and catch an injector leaking. A stock truck with the updated calibration may have and should have caught that. Too much oil/fuel usually causes 2 and 8 to run hot (rich). I tell people with modified trucks that they turned them into boats which means now we have to work on them every weekend and there is no guarantee EVER because I ate one too just like you did but I will never again.
@mrfanman2u
10 жыл бұрын
That's about what I thought. My concern now is that they are now put the injectors and hfpf out of the fubar'd motor into the new motor. I warned the owner of the shop... and he told me that a leak from the pump would be impossible... I say... where the hell did 5 gallons of fuel come from in 10 minutes? Either the new injector, or that pump. They were FMC Reman pumps. I've done all I can... and it won't be on me... you just confirmed what I suspected... Happy New Year.
@DieselTechRon
10 жыл бұрын
Brian Hicks sometimes we can catch a leaking pump by commanding the fuel pump on with the IDS and leaving the drain plug out to see if any fuel enters the crank case. You can also run these without the valve covers on them to see if the injectors are leaking. I've had the injectors themselves leak, not the lines. But at minimum I would do the crank case test and monitor short fuel trim
@jorgebarrera8328
6 жыл бұрын
Can be lifters as well
@Deere-uh4go
5 жыл бұрын
My 7.3 sounded just like that but way louder. Broken rocker arm and bent push rod. Cost less that $30 and back on the road.
@fallingleaf6793
5 жыл бұрын
Did you lose oil pressure to when this happened? my truck made the same noise and had a pushrod off the rocker but I have no oil pressure as well
@tuckersmith8787
6 жыл бұрын
This is a really great video. I have an 08 job 1 6.4 that I had EGR and DPF deleted at 77K, right after I bought it. It had been well maintained, which is not saying much considering the damage that was already done implicitly by the EGR/DPF. The truck has 98K now and runs like a racehorse, with stellar fuel economy for what it is. I have an occasional and random popping into the airbox that no local mechanic can diagnose. Any ideas would be greatly appreciated!
@fordsixfo
5 жыл бұрын
tucker smith ever have an idea or figure what it was mine sounds like a vhhhhhhh noise
@DieselTechRon
10 жыл бұрын
You can have someone or a dealer check it with the ids updates. Or use a scanner that tells the calibration and google it.
@kyleheather0416
2 жыл бұрын
I'm having the same problem. My question is will it Hurt the engine driving like that till it gets fixed
@jackmann1314
4 жыл бұрын
R.I.P. DAN WAS THE BEST.... PEACE
@fatkat311
3 жыл бұрын
Dan?
@jackmann1314
3 жыл бұрын
DIESEL DAN THE REPAIR MAN
@pepinillorick1214
5 ай бұрын
Thank you señor
@desertratconnieconstance8557
Жыл бұрын
Did u have to remove the cab and front clip to service the valve train?? My brother in-laws is doing the same thing. Ur link was very helpful. Thank you.
@itsdanimusic8395
8 ай бұрын
Where are you located? I have a f350 with 6.4l and it makes noise only when I give it gas when idling it sounds fine. Do you know what it is?
@scottreid4170
9 жыл бұрын
Ron, thanks for your videos as they've helped me tremendously. I have this exact truck with the "thumping" sound, but I shut it off immediately and drained some oil out. Noise seems to have gone away. You ever seen that before? If so, is it safe to drive or should I just replace everything you showed in the video? Thanks in advance.
@MIHfishing
Жыл бұрын
Why does my truck 2023 6.7 powerstroke make a loud pop when I hit gas hard in park?
@robertburnett6252
7 жыл бұрын
Ron. My name is Robert I have an 08 Ford f450 lariat auto 6.4. We have replaced the rocker arms and pushrods. I have what it sounds like a lifter tapping in the engine. Would a lifter cause some type of misfire or something other than sound on s cylinder? I have no codes egr dpf cat and muffler delete. Also I have a slight amount of white smoke in the tail pipe. No change in performance at all. Runs like a top. Only smokes when I come to a stop. It clears up as I drive.
@lloydporche4790
7 жыл бұрын
I have to replace the driver side rocker assembly the passenger side was done 11000 miles ago. I'm very capable of doing it. do I have to align the crank to be able to install the Rockers or can I just align the push rods and sink them down slowly then torque them down?
@antonioamado7813
Жыл бұрын
Thank you sir, I’m learn your video!!!!!
@jaymegriffiths1162
9 жыл бұрын
Hey Ron Thanks for uploading the video! I have a friend who recently asked me to look at his 2010 6.4 powerstroke. He said he heard a noise like air rushing and then the truck started running poorly and leaking oil. I found 3 of the glow plug boots pushed out of the valve cover and oil running down the sides of the engine. I also noticed a massive amount of exhaust coming from the crankcase area (checked at the oil fil cap) oil level is normal but engine is missing and lots of white smoke. I think the #2 piston is cracked because it threw a misfire cyl 2 code. Does this sound right or is there anything else I should check before removing the engine? (the glow plugs are there, I read somewhere they can break in half and blow out)
@Mebob2001
9 жыл бұрын
Jayme Griffiths i dare say your right dude, he needs a new engine
@joeroberts8008
Жыл бұрын
I just went through this with my 2010 ps truck blowing a glow plug out. Replaced them then had a misfire while idoling in -20 weather. I ended up replacing all the injectors. I just got my truck back today. My truck got 227,000 miles on it.
@jaimeflores8296
Жыл бұрын
Haga de Same Problem en Mind So Thank You For Show Me muchas gracias
@gdlautomechanic
10 жыл бұрын
Im working on a 6.0 2007. it has a loud noise on the rocker arms, specially on #1 cylinder. it sound louder around 1500 rpm's. sounds like almost taping on the valve cover. is there a common failure that can cause that? engine has no misfire or popping noise. complaint was the noise, but did had a code with injector number 6 and 8 and also a Camshaft sensor.
@Dantheman-bh4xx
9 жыл бұрын
just bought a 2010 f350 6.4. guy said a lifter had failed causing the cap holding the rocker tip to fall off on the #7 exhaust rocker. had a tick and ran rough. took the valve cover off and sure enough it has mechanics wire holding the tip on. ever heard of the tip falling off?
@Dantheman-bh4xx
9 жыл бұрын
Dantheman in case anyones wondering it was a bad cam lobe fully rebuilt the engine runs great now
@alexismiranda9885
2 жыл бұрын
I have the 6.0 engine it is the same to change the rocker arms the same thing is happening to me
@vilitransit4597
6 жыл бұрын
It’s a common problem on one bank only or both banks? I have same issue and not sure if I should order parts for both sides
@yamahayz228
9 жыл бұрын
ive gotta question for ya, ive done a full egr delete and tuner and ive started to notice like a ticking noise coming from the engine could it be rockers or something way worse
@rainhadoskyvalento8123
8 жыл бұрын
Im having the same problem, does it also make the truck weak and smoke diesel from the intake in low rpm? My truck is shipped as well
@vsanchez1301
2 жыл бұрын
Hey Ron I hope you get this massage you think this could be the same thing
@hungrynapps
8 жыл бұрын
my head was replaced n I believe all.those stuff was replace. so my mechanic say.. n.my engine loud as yours in d pic. please tell me a list of stuff I have to change n.what needs to be adjusted
@ecseymour3
10 жыл бұрын
Hi I hope you don't mind but have a couple questions for you. I own a 6.4 I live in North Dakota where it gets very cold usually around -30 how often should I change my oil and also anything else I need to look out for thanks Ed Seymour
@DieselTechRon
10 жыл бұрын
Oil changes really vary by idle time. I've had guys go over 7500 with no problems and others that could not go 1000 miles because of too much idle time. The main killer is not completing the regen process. Also vehicles need to be driven until they reach operating temp. Diesels will never reach that if idling and just around town driving in cold weather. Diesels actually create a lot of heat so they are more robust. But that also causes them to take more time and work to warm up. If you have the newest calibration it monitors a lot more and can warn you of the oil temp being too high or overfilled.
@ZHPBrent
3 жыл бұрын
How much would a repair like this be?
@sig45only
10 жыл бұрын
Thanks for your time making allthis videos they are very useful. I have a concern about 6.4 engine, the engine does a very annoying screesh by the turbos, it uses to be when the engine was cold, now itdoes some times at normal operating temperature. Any help would be appreciated. Thanks and best regards.
@JasonG146
10 жыл бұрын
Exhaust leak
@rondeltritt5047
3 жыл бұрын
I had this sound pop up shortly after an oil change but I didn't use the 15/40 can that be a problem.
@mikemike827
2 жыл бұрын
I thought it would be more noticeable but I didn’t hear anything.
@kevinhernandez2231
Жыл бұрын
Where can we buy the parts you suggested?
@ryanjones1735
4 жыл бұрын
I just “fixed” an 08 with this issue. It ran great for two minutes and it happened again and the same cylinder is showing bad on the power balance. What has happed? Could their be additional damage to the lifter or cam?
@dannychinh6660
4 жыл бұрын
Same thing happened on mine. Bad lifter.
@stevecox5219
10 жыл бұрын
I have the same popping on a 6.0. Have you seen the issue on a 6.0 also?
@michaelj5261
8 жыл бұрын
How much did you charge to do this repair? Im in California and need to get this done. Nervous how much this is going to cost.
@alfredohernandez1124
7 жыл бұрын
Michael J how much they charge u for this work i have the same problem
@michaelj5261
7 жыл бұрын
All said and done it was about $4600. I had a bad piston in cylinder 8. Built up pressure from diesel fuel getting into the block caused piston to hit the valve and bend it. Thank God no cylinder damage
@florramirez6319
6 жыл бұрын
Mine does the same but a 7.3 can that be it?
@muthafukajones4536
6 жыл бұрын
Did he only do one side?
@hddm3
10 жыл бұрын
keeps ron busy and making money though
@JohnDiMartino
10 жыл бұрын
NAVSTAR obviously cut a lot of corners with this engine.i don't care if it got an oil change every 15k,. Rockers shouldn't wear on a
@bryanmartinez6600
7 жыл бұрын
John DiMartino it's a redesigned MaxxForce 7 Engine originally producing around 200 240 Horsepower but then Ford got it made 350 Horsepower then goes in tunes and making now 400 or more horsepower can't blame the Engine it's running stock parts at over twice the output they even made it for
@ps3dethman1
10 жыл бұрын
anyone notice how dirty the oil was.. it was already turning into slug
@johnnygonzalez7874
8 жыл бұрын
Around what mileage would they have to be checked ?
@DieselTechRon
8 жыл бұрын
no set miles. if maintained they don't wear out. make sure the regens compete
@Dexter_Solid
8 жыл бұрын
6.4s are pure garbage, I work on them day in and out. This is wear on the rocker feet(between pushrod and arm), seen them wear through and break the arm off on more than one occasion. Roughly 180,000km on the odo is when they go. (like 110k miles). Those feet must be made of recycled pop cans.
@jogro2
10 жыл бұрын
Egr and dpf delete saves money and time
@juansantibanez7754
6 жыл бұрын
I had that same sound by my air filter on my 08 6.4 but then it went away on its own and sometimes it comes back I have full delete with with 5" straight pipe could it be the same problem or what could it please help! Thanks
@Caballero24v
6 жыл бұрын
juan santibanez same problem here! I need help, howd you get it fixed??
@J.Rocha54
Жыл бұрын
@@Caballero24v did you ever figure out what the issue was?
@Mebob2001
10 жыл бұрын
i wish people would just change there freaking oil..... and ofc all the other fluids! inpect there truck for leaks once a month! new diesel's are no longer just get in and turn the key!!!
Пікірлер: 83