As a complete novice was a little nervous but entire job took less than 15 minutes. Great video that walks you through everything, thanks
@HaynesManuals
11 ай бұрын
Glad it helped!
@Madara2B
8 ай бұрын
yeah changing the car lights are something first time drivers should give a shot.
@Winkmyster
6 ай бұрын
You guys make the best tutorials, very direct, step by step, no time wasted.
@HaynesManuals
6 ай бұрын
Thanks
@abbots69
4 ай бұрын
Haynes , the masters of DIY repair - brilliant professional step by step video far better than the home videos of amatures and their wonky filming
@HaynesManuals
4 ай бұрын
Thanks!
@john2856
5 ай бұрын
Much better then the official Ford movie. Thank you. Great help!!
@HaynesManuals
5 ай бұрын
Wow, thanks!
@murf537
Жыл бұрын
Would be best to check the light is working before fully re-fitting all the fixings! My early 2017 Fiesta looks the same - but I needed to lift upwards slightly to release the headlight unit from the locator underneath (just snaps out/ back in). I only unfastened the cross head scrivet (screw/rivet) beside the lower Torx fixing. The multipin electrical connector connects to ALL the bulbs in the unit so none will work when it is uncoupled. Once you have completed fitting a new headlight bulb, you will realise it is pretty straightforward as long as you have the correct Torx head tool to undo the front and rear fasteners (seem to remember it being Torx 30 but stand to be corrected), Replace in pairs - once one bulb goes you can be sure the other isn't far behind. And the second will be easier than your first. Good Luck everyone.
@HaynesManuals
Жыл бұрын
Thanks for your comments
@reklaminho
Ай бұрын
Thanks!
@999raycurran
2 ай бұрын
Fantastic, just what i was looking for. Will have a got at this today
@deathrunning
9 ай бұрын
Is it just me, or did it take a concerning amount of force to lift the headlight unit out once everything else was unscrewed? I was genuinely worried that I was going to snap a clip or something.
@JMB730
8 ай бұрын
Okay problem the two screws at the start will not come out I’ve tried just unscrewing them I’ve tried using a flat head to from underneath to try push it up and unscrew at the same time just can’t get them out
@desireeholloway3353
20 күн бұрын
Same here!!
@JMB730
20 күн бұрын
@@desireeholloway3353 eventually i just popped them out with a flat head screw driver. dont worry it wont break them you can just use them again when putting the bumper back on
@Ulysses042
2 жыл бұрын
Thank you! This really helped me out today.
@HaynesManuals
2 жыл бұрын
Glad it helped!
@abbastanveeruk2177
9 ай бұрын
Thanks too much easiest way , helped too much 👍
@HaynesManuals
9 ай бұрын
You're welcome!
@MrSlipRed2
Жыл бұрын
Thank you for this. Really helped.
@HaynesManuals
Жыл бұрын
Glad it helped!
@Lagaanjoh
2 жыл бұрын
I dont get the white "clip"?! The thing what the unit holds underneath. You need to push the unit on it or slide? And thank you so much for this vid. Its really accurate! 👏🏻👌🏻🖤
@castelnedd
10 ай бұрын
Thank you. That video was so helpful 👍👌💯
@HaynesManuals
10 ай бұрын
Glad it was helpful!
@chrispickard5199
Жыл бұрын
my issue appears to be getting that fastener to release, where the headlight and the front of the car hold together
@JMB730
8 ай бұрын
Is it the four screws across the front end if so did u find a fix I have same issue
@chrispickard5199
8 ай бұрын
@@JMB730 yeah as far as i can remember, scrwdriver eventually worked, or something like that, once i could get under it
@JMB730
8 ай бұрын
@@chrispickard5199 thank you I eventually got it i used a flat head and just popped them out
@benlally9767
Жыл бұрын
Thanks very much for the video:)
@HaynesManuals
Жыл бұрын
You're welcome!
@alecsvaly
2 жыл бұрын
Good video.Really help a lot. God bless you
@HaynesManuals
2 жыл бұрын
Glad it helped
@flamingosedai1820
8 ай бұрын
Yeah taking the headlight enclosure out is impossible without breaking something. Even after taking out all of the screws in the video, it still is stuck to something. I'm going to have to bring it in. Why does Ford make it so complicated to fix something so simple???
@user-uh5ll9hv5e
7 ай бұрын
There are little lugs on the headlamp unit that slot under the front side panel. The video doesn't seem to mention these. You need to lift and twist the headlamp unit at the same time or these little lugs will prevent you getting it out.
@edoardo0802
2 жыл бұрын
i did everything correct but the left headlight it is not sitting right after i removed and installed it again, what can i do?
@nurawis1
2 жыл бұрын
Something not right when you re-install the headlight. Maybe it is not sitting to it place properly.
@d4tjr165
2 жыл бұрын
What about the multi plug on the main beam bulb ?
@HaynesManuals
2 жыл бұрын
The multiplug is disconnected at about 1'20"
@rapinncapin123
Жыл бұрын
What tools are needed...
@HaynesManuals
Жыл бұрын
A cross-head screwdriver, and a Torx screwdriver should be all you need.
@TheExxl
2 жыл бұрын
so high beams are h7 and low beams h1 ?
@HaynesManuals
2 жыл бұрын
UK market: H7 dipped beam, and H15 for the main beam
@michaelbamber4887
10 ай бұрын
Great, what happened to just removing the back an replacing the bulb? What happens when your down the road? Say France were you need to carry bulbs by law? Waste of time.
Пікірлер: 46