2012 Ford focus SEL temperature gauge Spike, WARNING alarm, and overheating concerns.
Same issues on Ford Focus 2012-2016
**Check out updated Part 2**
• Fixing Ford Focus & Es...
New parts needed - Coolant Reservoir Expansion Tank, Antifreeze/Coolant
1) TOPAZ CV6Z-8A080-A Coolant Reservoir Expansion Tank with Cap for 2012-2013 Ford Escape Focus Transit Connect C-Max
Amazon - amzn.to/2yFqdiE
2) Ford Genuine Fluid VC-3DIL-B Orange Pre-Diluted Antifreeze/Coolant - 1 Gallon
Amazon - amzn.to/2WfpYDY
the best coolant here - Amazon - amzn.to/2WfpYDY
Ford Genuine Fluid VC-3DIL-B Orange Pre-Diluted Antifreeze/Coolant - 1 Gallon
Fixing a tiny crack in the coolant reservoir of a 2012 Ford Focus with a 2.0L engine can be done with some basic tools and DIY skills. Here's a step-by-step tutorial to assess and fix this issue:
*Note:* Ensure that the engine is cool before starting this repair.
*Materials/Tools Needed:*
1. Replacement Coolant Reservoir
2. Screwdriver
3. Pliers
4. Hose Clamps (if needed)
5. Coolant
6. Safety Glasses and Gloves
*Step 1: Safety First*
Always wear safety glasses and gloves to protect yourself from any coolant spillage or sharp edges.
*Step 2: Open the Hood*
Pop the hood of your Ford Focus and locate the coolant reservoir. It's usually on the passenger side of the engine bay, near the front.
*Step 3: Drain the Coolant*
Position a catch pan or bucket beneath the vehicle to catch any spilled coolant. Carefully remove the cap from the coolant reservoir and set it aside. Use pliers if it's difficult to open. Allow the coolant to drain into the pan.
*Step 4: Remove the Reservoir*
Using a screwdriver, carefully disconnect any hoses or clamps that are attached to the reservoir. Keep track of their positions to reconnect them later. Once disconnected, remove the reservoir from its mounting brackets.
*Step 5: Inspect the Reservoir*
Examine the reservoir for cracks. If you find a small crack, you can attempt to repair it with epoxy or a plastic welding kit. If the crack is significant or if the reservoir is severely damaged, it's better to replace it.
*Step 6: Repair (If Necessary)*
If you choose to repair the crack, follow the instructions on your epoxy or plastic welding kit carefully. Make sure the area is clean and dry before applying the repair material. Allow it to cure fully before proceeding.
*Step 7: Install the New Reservoir*
If you're replacing the reservoir, insert the new one into the mounting brackets. Reattach any hoses or clamps that you disconnected earlier. Make sure all connections are secure.
*Step 8: Refill with Coolant*
Using a mixture of coolant and distilled water (as specified in your vehicle's manual), refill the coolant reservoir to the recommended level. Check for any additional leaks around the new reservoir.
*Step 9: Bleed the System*
Start the engine and let it run with the radiator cap off. This allows any trapped air to escape from the cooling system. Keep topping up the coolant as needed until the level stabilizes.
*Step 10: Check for Leaks*
Inspect the area around the new reservoir for any signs of leaks or drips. Also, monitor the engine temperature to ensure it doesn't overheat.
*Step 11: Close the Hood*
Once you're confident that there are no leaks and the engine is running at the correct temperature, replace the radiator cap and close the hood.
By following these steps, you can assess and fix a tiny crack in the coolant reservoir of your 2012 Ford Focus without the need for a mechanic. However, if you're uncomfortable with any part of this process, or if the crack is extensive, it's advisable to seek professional assistance. Coolant system issues are essential to address promptly to prevent overheating and engine damage.
Thanks a to for watching the video and reading this!
Please give it a like and comment if this was helpful!!
🔴 Subscribe to this channel for more great stuff:
/ @nickkosta
Негізгі бет Ford Focus 2012 overheating temperature spike, DO NOT go to a mechanic! Fixed cheaply, in 30 minutes
Пікірлер: 154