Great job showing all the different ways to open and close various tabs. Devil is in the details and that probably kept a load of folks from kicking the family cat. My cat wants to thank you personally.
@MinecraftLover58
2 жыл бұрын
You're the first one to show how to remove the air hose! Thank you so much!
@Saltbox97
2 жыл бұрын
Really glad to hear this helped. Thanks!
@radchad1234
Жыл бұрын
This fixed the issue in my wife’s car, perfectly presented. Thank you!
@Saltbox97
Жыл бұрын
Glad it helped
@joeross7948
10 ай бұрын
Ford recall 18S32 on this CPV part back in 10/2018. Apparently replaced before I bought it. After replacing warranty is 12 miles/1 year. Thanks for the video because I’ll replace it myself.
@Saltbox97
10 ай бұрын
Thanks for your feedback. It’s awesome to hear that folks are able to do the repairs themselves.
@gabeayala5659
2 жыл бұрын
Thank you for this video. Saved me some money taking it to the shop. I was able to fix mine in 5 minutes.
@Saltbox97
2 жыл бұрын
Excellent!
@unknownun-sp1wp
16 күн бұрын
On a 2016 ford focus SE 1.0l the vaster canister purge valve on top on the engine. The ford Focus 2.0 not the same as the 1.0l focus. Only videos I find are on the 2.0 ford focus.
@NeedlessJ93
Жыл бұрын
Thank you very much! I wasn't sure about reassembling until I saw this - just push ends on and then lock tabs will engage 🙂
@Saltbox97
Жыл бұрын
You got it. They do look tricky at first
@bryanmeier8251
2 жыл бұрын
thank you so very much i have the same problem. dealer charges $189 to diagnose test and more to fix . thanks to you and video i know whats the problem and a easy fix 👍
@johnhughes3429
5 ай бұрын
Dude. Glad to be the 1000th” like”. Excellent video. You saved me a trip to the mechanic. 5:33
@Saltbox97
5 ай бұрын
Right on. You’re a good person. Glad this helped.
@richardruybaliii5320
2 жыл бұрын
I have a 2015 Ford Focus se and this is today’s code as I went to a different ford dealership. I recently had the low pressure fuel sensor replaced due to stall out issues. Had to have it towed last week due to incorrect fuel gauge said it had 30 miles left on tank but not the case. Yet started after refueling next morning. today the check engine light is on, was intermittent last week. The last two weeks having random engine revs in 1500-1800 rpms even after full down gear to stop and in neutral at stop light. I also found that if I I start my air conditioning unit for a few seconds it’s corrects the revs and then I turn off the air and drive normally.but I’m going to try this as the dealership is far out in service appointments, for 7-10 business day just to get it looked at, not even worked on. Thankfully this new dealership guy helped scan with the car today using obd reader, this how I know what code it’s giving and it’s description was vacuum issue, he suspected purge valve issue and the descriptions on screen Indicate as such.
@roshiniayoungblood8681
2 жыл бұрын
I’m having the same issue… but I’m not sure what parts to get.. 😩😩
@roshiniayoungblood8681
2 жыл бұрын
Is it the fuel sensor?
@richardruybaliii5320
2 жыл бұрын
@@roshiniayoungblood8681 not sure yet but was replaced a month ago on my vehicle
@richardruybaliii5320
2 жыл бұрын
@@roshiniayoungblood8681 autozone had the part he specified under the duralast brand but I saw on the computer screen at the store they had the dorman brand 911-777 part for the yr of my car so I believe it’s the same part.
@derek790
Жыл бұрын
Thank you so much! My 2016 Ford Focus was giving me P1450 and P2195 codes and was also difficult to start after fueling. This completely fixed it! Purrs like a kitten again.
@Saltbox97
Жыл бұрын
Glad it helped
@edwardlouis79
Жыл бұрын
What's the part
@condor4679123
10 ай бұрын
First thing to check before pulling things apart is if this is a real problem. I have seen with my Ford Escape 2014 that if there is a temperature drop overnight combined with an empty gas tank. Erase the code and everything goes back to normal for a few more months.
@brandonvega9698
5 ай бұрын
This exact scenario happened yesterday and it’s my first time getting an error code. I religiously maintain my car so now I’m second guessing
@ayobyrd
2 жыл бұрын
This was an extremely helpful video that made this so easy thank you so much
@Saltbox97
2 жыл бұрын
You are so welcome!
@philruiz2462
Жыл бұрын
Excellent tutorial bud
@Saltbox97
Жыл бұрын
Thanks very much!
@danielxitshembisomaphosa7161
Жыл бұрын
Having this issue on my 2015 ford focus, occured the following day afetr filling my tank.
@AeroRamer
Жыл бұрын
I just purchased a 2017 Focus SE and plan on keeping a spare purge solenoid in the trunk in case this happens to me on the road.
@arthurwatkins5975
2 жыл бұрын
thank you best demonstration i seen and common sense by not replacing the steel bracket!
@josephpercy5759
2 жыл бұрын
You dont have to take the complete assembly off to make sure thats the problem,disconnect closest to firewall put hose in while car is turned of suck in hose you should not get any draw if not stuck open start car you should get draw now good purge valve move on
@5doublebass
2 жыл бұрын
Great video, was able to do the fix real quick
@melodyboudreaux7141
2 жыл бұрын
I had to show your video to my mechanic!! Thanks!
@rapinncapin123
3 ай бұрын
It didn't get rid of my p1450 or 0420, but it did get rid of my P2196.
@KrisGeib
2 жыл бұрын
Ah yo! Great walk through guide, I'm sure you just saved me $200+ cheers mate 🥂
@ibbyultrainstnct4029
Жыл бұрын
Thank you so much man. You’re a life saver and life savings saver 😅.
@chrisberney8777
2 жыл бұрын
I replaced the same part today on our 2014 Ford Focus, video was very helpful. Thanks
@Saltbox97
2 жыл бұрын
Glad to hear this helped. Thanks
@popoi47asca
2 жыл бұрын
Hi, thank you for your video, I followed every step on your video, your video is very informative and helpful. I have a question tho, after I install the new part, will the check Engine light go away? Mine hasn’t?
@Saltbox97
2 жыл бұрын
You may have to wait until that same emissions monitor is run again for the code to clear. The monitor will run when certain conditions are met such as coolant temp, ambient temperature, etc. You could disconnect battery for 10 minutes or pull ECM fuse if you don’t have a code reader. The requirements for running the EVAP monitor vary depending on the year, make and model of your vehicle. Generally speaking, the fuel tank must be 1/4 to 3/4 full because a near empty tank or a full tank can affect the accuracy of the EVAP self-test. The ambient outside temperature must not be too hot (above 95 degrees) or too cold (below 30 degrees) because this affects fuel volatility and the amount of vapor inside the tank. The vehicle must also have sat overnight or for at least 8 hours without being driven. On some vehicles, the EVAP monitor runs when the vehicle has been cruising on the highway at light throttle at a speed of 45 to 65 mph for at least 10 minutes or more. All of the components in the EVAP control system must also be functioning normally. The presence of any EVAP related DTC fault codes will prevent the EVAP System monitor from running.
@popoi47asca
2 жыл бұрын
@@Saltbox97 thank you soo much for you video and your reply. I followed all instructions on your video, im grateful that you added the part number on your description, it made it really easy to find the part that i needed. your suggestions from your reply on what to do all worked. I did do the 10mins battery, I drove my 2014 Focus SE till there was 1/4 gas in the tank, i left it in the garage with the hood up so it wouldn’t be too cold or too hot, I didnt drive my car during the weekend. Then on Monday, drove like it did before the “check engine light” came on. Drove to the gas station, didnt choke up anymore. I’m extremely grateful for your video, you saved me SOOO MUCH MONEY, I bet i would be charged for soo much with i went to Ford dealership. Thank you thank you thank you.
@JeronimoStilton14
Жыл бұрын
@@popoi47asca I know this is old but my ford dealership is looking at 350 bucks to do the fix
@bryanwinston869
8 ай бұрын
Good video, getting ready to do mine..in the cold!
@jonthompson8807
Жыл бұрын
had to replace mine. after they checked at the dealership and said it was ok. after i paid to have my fuel pump replaced. fml
@bsto5000
2 жыл бұрын
Great video. You explained my situation perfectly. Thank you!
@Saltbox97
2 жыл бұрын
That’s awesome to hear.
@tonyray518
Жыл бұрын
This worked for me, thanks for the good information!!
@Saltbox97
Жыл бұрын
That’s great news! Glad this helped.
@TanachSpot
Жыл бұрын
Yep my purge valve will make my car stall too I’m not a mechanic but the shop was going to charge 1400 dollars to fix this wow
@EASThePlague
2 жыл бұрын
Is this similar to the 2018 model? I just got this code the other day, gonna have a wack at it after I do some internet research. This video is all I found
@djbuckley6087
2 жыл бұрын
Thanks! This helped me fix my problem.
@Saltbox97
2 жыл бұрын
Great to hear!
@ossa4772
2 ай бұрын
thank you very much, you the best
@kevinmcfarland1661
Жыл бұрын
I have a 2014 ford focus. P1450 code. Stalls after fill up. I just replaced the purge valve solenoid but still have a check engine light on.
@kevinmcfarland1661
Жыл бұрын
Do i need to reset the code? Just bought a scanner capable of it off of amazon.
@Saltbox97
Жыл бұрын
The light won’t turn off right away as computer needs to run the monitor again under certain conditions. You can clear it with your new scanner which is way more fun than waiting for the monitor to run again which may take a few key cycles.
@teddiazjr.6223
2 жыл бұрын
Great video n demo
@blackisback74
Жыл бұрын
I have a 2012 Focus and mine has another valve or something connected to the same hose about 6" behind the purhe valve
@matthewkeisling2776
Жыл бұрын
Very helpful video. I had a check engine light and recurrent code, and also difficult starts right after fueling up. I purchased the factory replacement valve assembly (not much more $ than aftermarket,) and followed this video to make the repair. Knowing that blowing air to test the old valve gave me more assurance. I cleared the codes and all good so far. ✊🪵
@TheViCTimm1
3 жыл бұрын
Hello, I have in my Focus 2014 the code P0443 and P0446, both related to a fault in the purge valve and ventilation valve circuit. This could be solved by changing the part that you changed? or is it specifically checking the wiring?
@Saltbox97
3 жыл бұрын
check circuit wiring first. you can also apply the 12v to see if solenoid works
@bike0662
3 жыл бұрын
Can this also cause your car to read the wrong amount of gas in your tank?
@Saltbox97
3 жыл бұрын
this part would not affect the fuel level indication.
@richhooker1263
3 жыл бұрын
That would most likely be a faulty “fuel pump sending unit”. Typicall that will be integrated to the fuel pump. Could also be a wiring issue
@ivandelatorre3937
2 жыл бұрын
Yes, SIR!!!!!!! Thank you 🙏🏽
@Saltbox97
2 жыл бұрын
You got it!
@betitocarranza
Жыл бұрын
Hello, I just changed that piece but the engine light doesn’t turn off, I need to go to the autozone and request to erase the code? Thank you.
@Saltbox97
Жыл бұрын
The light won't go off right away. The computer needs to run that specific monitor again before it goes off which could be a few driving cycles. You can diconnect the battery for 30 seconds (but then you'll need to re-set clock and radio stations). Or wait until the monitor runs again. Save your money on a code clear unless you know a pal with a scan tool.
@nachoperez371
2 жыл бұрын
Tank you helpful video
@adrenalin9
3 жыл бұрын
Very good job. Thanks
@funnykidd
3 жыл бұрын
The best video on this topic for Focus. Thank you. Fixed mine yesterday, easy peasy. Rode the car afterwards, no problem. But the service engine light is still on. How do I fix that?
@Saltbox97
3 жыл бұрын
If you don’t have a scan tool to reset, you can disconnect battery for a couple minutes or just wait a few drive cycles for the evap monitors to see that there are no longer any issues.
@kellyallman3873
Жыл бұрын
Is this part also 911777 or thats different I searched for bwd cp894 and nothing comes up but this part
@Saltbox97
Жыл бұрын
Yes, that looks like the Dorman part that is the same.
@jonzerox7
Жыл бұрын
Muchas gracias
@ytoal
10 ай бұрын
Thank you!
@Saltbox97
10 ай бұрын
You're welcome!
@safemoonswayze5552
2 жыл бұрын
You're a legend.
@Saltbox97
2 жыл бұрын
Perhaps in my own mind ;-)
@safemoonswayze5552
2 жыл бұрын
Solid video on this topic
@coreymarshall1078
2 жыл бұрын
THANK YOU SIR
@youwish3439
Жыл бұрын
I got a 12 mine read full all the time and when I go to fill tank it clicks like it’s full
@JessNW0lfG4NG
2 жыл бұрын
My 2012 Focus SE is stalling after driving around for a while. Example: I'm driving, reach a red light on flat or hill and as I press on the gas pedal it just doesn't move and starts sliding backwards if I'm on a hill as if it's not in gear and struggling to even Rev and drive off. I can feel as if my car is choking and struggling to move. Would this solve my issue? I've personally replaced all spark plugs, air filter is still fresh and right now I went and bought a new fuel filter to replace later on today or tomorrow, will this fix help my focus or could it be something worse?
@popupheadlights
2 жыл бұрын
This defiantly causes stalling, it used to happen to my girlfriends car before I replaced the valve, when you fill up does the car wanna die? If you can go to an auto parts store like autozone and ask if they can read the OBD codes for you unless you have a scanner yourself. The issue in the video causes a Check engine light. If the code matches the video then there ya go part is 51$ at autozone and as is simple to put on.
@JackJackson3095866
Жыл бұрын
Just had this code pop up on my car today. Thanks for the video! Is there any kind of prep work that needs to be done prior to removing the old part?
@Saltbox97
Жыл бұрын
Not much, do it all from above and no special tools.
@jacobhardman6901
Жыл бұрын
My line has an extra baseball sized canister about 4” before the purge valve, the correct part number pulls up the one you used in the video with no extra canister, do you know what that can is for or if I can just use the new one without any problems?
@luissrangel390
2 жыл бұрын
Thanks a lot really helped!
@Saltbox97
2 жыл бұрын
Glad it helped!
@gosgraproperties8687
2 жыл бұрын
I appreciate you sir
@jonathanhummer6867
Жыл бұрын
2016 Ford Focus. My codes read P1450 UNABLE TO BLEED UP FUEL TANK P144A EVAP EMISSION SYSTEM PURGE VAPOR LINE BLOCKED P0456 EVAP LEAK DETECTED Could this fix all 3?
@hardhittinz
Жыл бұрын
Did you get it fixed? If so was it the purge valve
@jawsvt8221
2 жыл бұрын
I have a 1.0 ecoboost focus and im get this code will this part fit my car??
@user-hb1yx5tm9f
Жыл бұрын
Do you have to take the piece connecting it to the intake off or if you can fit your hands in there do you even have to take it off it at all?
@Saltbox97
Жыл бұрын
I only took off what you see and worked around everything else.
@mattwitherspoon7170
2 жыл бұрын
I have a 2017 focus sel with the same problem, would this part fit my vehicle?
@mattwitherspoon7170
2 жыл бұрын
Update: It was super difficult to fit in because the air intake hose only removes on one side but i got it in and it fixed all of my problems!! No more shaky start up after fueling and it got rid of my check engine light
@Saltbox97
2 жыл бұрын
That is awesome news!!
@elizabethjmartinez7044
Жыл бұрын
Hello I was getting gas and all of a sudden , the car won’t turn on why does this happens i just got it from the dealer a few months ago will this happen anytime I put gas ? Or does this car comes with a lot of issues anybody knows ?
@SOGZero6
3 жыл бұрын
Is the 2014 Ford Focus set up just like that? And where did you get the whole piece together at?
@Saltbox97
3 жыл бұрын
Ordered on Amazon. Was cheaper there than my regular wholesale supplier.
@kellyallman3873
Жыл бұрын
Question for you do you have to reset the code after replacing it or should the check engine light go off on its own? We just replaced mine yesterday check engine light is still on...
@Saltbox97
Жыл бұрын
The light won’t turn off right away as computer needs to run the monitor again under certain conditions. You can clear it with a scanner, or disconnect battery for 10 minutes, or just wait a few key cycle/trips for it to clear.
@kellyallman3873
Жыл бұрын
Thanks for the quick response we cleared the code no check engine light and no more stalling after getting gas awesome this video helped a lot thank you!!
@jvill6074
6 ай бұрын
My 2 green locks won’t come off one does but the other won’t come off
@jvill6074
6 ай бұрын
@saltbox97
@Saltbox97
6 ай бұрын
Try pushing the connector together (on) when trying to release green clip. If you are pulling apart at the same time it can be hard to release the green clip.
@jvill6074
6 ай бұрын
@@Saltbox97 thanks let me try that
@devonglowka6901
Жыл бұрын
Do I need to worry about any fuel pressure when removing the old purge valve?
@Saltbox97
Жыл бұрын
No, this is just a vent and no fuel in this line.
@devonglowka6901
Жыл бұрын
@@Saltbox97 Thank you, this will be my third one. The first was a factory defect and it was covered but 5 years later its the same issues with not starting after fueling. Shop guy said it's $50 and I can probably just replace it myself.
@jimfitzgibbon5492
3 жыл бұрын
Do you have the parts number for that valve?
@Saltbox97
3 жыл бұрын
I used this one. BWD CP894. Shop around for best price.
@Saltbox97
2 жыл бұрын
Dorman 911-777 as well
@jason8096
Жыл бұрын
This code just showed up in my son's 2017 Focus. He's had a P0456 code for a little bit beforehand. I'm wondering if this solenoid purge valve could be the cause of both codes.
@hardhittinz
Жыл бұрын
what did you find out? my focus has same code
@jason8096
Жыл бұрын
@@hardhittinz we replaced the purge valve solenoid and that fixed it
@hardhittinz
Жыл бұрын
@@jason8096 hey do you happen to have the part number or link to get the valve ? Mines 2018 but think all same .
@Primevals33
Жыл бұрын
any link to ordering the part???
@Saltbox97
Жыл бұрын
Check for specific vehicle fit: www.amazon.ca/Dorman-911-777-DORMAN-911777-PURGE/dp/B07CX8MHTK/ref=mp_s_a_1_4?dchild=1&keywords=ford+focus+evap+valve&qid=1631369316&sr=8-4
@tracycarpenter7142
3 жыл бұрын
Can you post the Amazon link to the correct part please
@Saltbox97
3 жыл бұрын
Check for you specific car. Here is link. www.amazon.ca/Dorman-911-777-DORMAN-911777-PURGE/dp/B07CX8MHTK/ref=mp_s_a_1_4?dchild=1&keywords=ford+focus+evap+valve&qid=1631369316&sr=8-4
@tjarthur7580
2 жыл бұрын
Would this work on a 2017 ??
@fadedhoops4582
2 жыл бұрын
so what part is? what do i ask for? pls jelp
@Saltbox97
2 жыл бұрын
Vapour canister purge valve
@fadedhoops4582
2 жыл бұрын
@@Saltbox97 thank you!
@kristianmopsticc2887
3 жыл бұрын
If the check engine light is not on and I have high rpms while idle will this help? Or since the check engine light is not on don’t worry ?
@Saltbox97
3 жыл бұрын
I’d be first looking for other sources of vacuum leak that may be increasing RPM.
@kristianmopsticc2887
3 жыл бұрын
@@Saltbox97 now getting shudders at stop lights and light is on gunna try this tonight
@BlueSky-po6ee
2 жыл бұрын
Can I get the part number to order it please
@Saltbox97
2 жыл бұрын
Hi Blue Sky. I posted a couple part numbers in the thread.
@Saltbox97
3 жыл бұрын
Check for specific vehicle fit: www.amazon.ca/Dorman-911-777-DORMAN-911777-PURGE/dp/B07CX8MHTK/ref=mp_s_a_1_4?dchild=1&keywords=ford+focus+evap+valve&qid=1631369316&sr=8-4
@joebagodonutssummertime8267
2 жыл бұрын
Is this code intermittent? Or can it be on all the time?
@Saltbox97
2 жыл бұрын
It can be intermittent if the solenoid is sticking but not totally failed open.
@joebagodonutssummertime8267
2 жыл бұрын
@@Saltbox97 New part will be here tomorrow, oem FORD. Not that that matters much anymore, lol.
@mejhon6592
2 жыл бұрын
I do not need to disconect the battery?
@Saltbox97
2 жыл бұрын
Not to replace component, just need key off. And Only if you don’t have a tool to clear code or don’t want to wait for the monitor to reset itself.
@mejhon6592
2 жыл бұрын
@@Saltbox97 ok ty
@Jedi_Luke
Жыл бұрын
What year is this car you have?
@Saltbox97
Жыл бұрын
2012
@joeh3679
2 жыл бұрын
What is the Part called? I know what to order.
@Saltbox97
2 жыл бұрын
Hi, Look for vapour purge valve or canister vapour purge valve.
@matthewmcmatthewson6578
2 жыл бұрын
So what you're saying is, get gas and then let the car sit for a couple hours. Thanks!!
@Saltbox97
2 жыл бұрын
Tee hee :-)
@lesgaal4017
Ай бұрын
Ford focus engineering junk the worst car I've ever come across with so much manufactured in built faults to cost consumers money. Just rubbish not to mention Automatic transmission problems from new.
Пікірлер: 148