Great video as ever Chazz - Just a quick tip if you are ever doing the job again, sweet talk the missus into letting you put the new hubs in the freezer the night before you fit them, contracts the metal and makes 'em go in easier - Having said that, the weather we have been having lately, just chuck 'em in the garden overnight...😗
@chumarbiker
Жыл бұрын
So nice video
@ChazzCoombes
Жыл бұрын
Thanks
@Wonlongpong
8 ай бұрын
The problem with this tool is the plate used to push against the bearing has the lip a bit too deep, as you stated, and hence restricts pushing the bearing in completely. I reduced the lip by about 1mm, which gave sufficient clearance to remove it after the bearing was in fully.
@train4905
7 ай бұрын
Awsome job😊
@petewilliams5517
Жыл бұрын
Hi chaz is 82mm std on most cars or do they come in different sizes say for my vw passat great video mate perfect timing for myself but not shore if my bearing are same keep up your great work buddy ty 👍🏻
@ChazzCoombes
Жыл бұрын
not 100% sure to be honest Pete, Ive seen a few different sizes so had to do some checks on size for mine. If i had access to a VW passat id be happy to check it. Thanks
@petewilliams5517
Жыл бұрын
Cheers chazz I'll look up the size of the bearings for my passat and I'll let you know if they are different I can see it was a pain in the butt mate you done well not to swear 😀 great video buddy and thanks for the link if my bearing are different size can you put a link up on here to buy if you get a bit of commission through your links helps you out mate if not let me know as I'm going to buy a set either way 👍👍
@gilleskirch7403
Жыл бұрын
You inserted the threaded rod the wrong way. The sleeve must be mount from the back and not on the front.And you have more power when you push and not pull your ratchet. :- ) but these bearings are quite firmly,just changed 2 bearings on a S-Max (343.000km) with this tool kit wich ist brilliant. But i removed the knuckle completely and to properly clamp it in a vise. Anyway, good job. (Y)
@adamdolezal4898
11 ай бұрын
You have more strength pulling ratchet upwards than pushing.
@chucky2316
Жыл бұрын
I need to borrow youre garage mate I've been wanting to do an oil change this whole weekend it's been chucking it down with rain
@ChazzCoombes
Жыл бұрын
ST is still in the air, im striping it down and giving it some undercoat treatment. And might do all the brake lines while im under there.
@chucky2316
Жыл бұрын
@@ChazzCoombes I'm only kidding mate garage would be nice to have somewhere dry to work. Annoying when you have all the bits. Where abouts are you somewhere in the coast judging by the seagulls I'm down in Devon
@ChazzCoombes
Жыл бұрын
@@chucky2316 I know mate, its cool. I have people wanting to use it close by but comes with needing my help sometimes lol. Your in Devon im the other side Kent coast
@chucky2316
Жыл бұрын
@@ChazzCoombes I managed to get it done today alright for another 6k😃,I have family in Kent I'm often up there I will give you a shout next time me and to he Mondeo are up there.
@AmetMoussi
Жыл бұрын
Hi Chaz, please could you tell me what is the torque of the three bolts+washer on the rocker cover, please, thank you. I was googling and in some places they sai 5nm and other 14nm but I don't know Please help me
@bradfergus7036
Жыл бұрын
Great video as always mate! Have you seen your Ken Block vid and the views?! Proper blown up!
@ChazzCoombes
Жыл бұрын
yeah i know right gone mad that one, so was worried about release my videos again after that one.
@paulmayou370
Жыл бұрын
Great work bro the car will drive like new the rate your going lol oh and end music i thought i was in Ibiza lmao
@ChazzCoombes
Жыл бұрын
Lol, only you would think that bro. Yeah giving it some tlc. Then can get back onto the ST videos
@pabloarris
Жыл бұрын
Good job. Its all a learning curve, I bet you could do the other side now in less than half the time. Just one tip, copper grease is not a very good lubricant its an anti-sieze its much better to use a moly grease like CV grease for applications like puller threads it would of also worked well on the splines on the driveshaft helping stop wear and making removal easier next time.
@nigeldickinson9848
9 ай бұрын
what name of the kit is it your useing
@amblernectar
Жыл бұрын
Cheers for making the vid
Жыл бұрын
82mm? no 78mm?
@TheCorrel2000
Жыл бұрын
I have a galaxy 2007, after seeing this I'm buying that tool. What a gem!...... This is the post I put a few days ago. How having bought the tool and try to use it I found that the black ring wouldn't go between the back of my old hub and the knuckle, I have message the seller in case they've changed the design in some way and it now doesn't but as you have had no reply.... I now have my car in pieces and no way of removing my old wheel bearing I can't add a photo on here otherwise I would have done
@ChazzCoombes
Жыл бұрын
deffo worth the purchase
@stillasgoodasnew
Жыл бұрын
Nice job, could you of taken the hub/knuckle off taken to a garage and asked them to press the bearing in or purchased your own hydraulic press?
@ChazzCoombes
Жыл бұрын
I tried it in my own 12tonne press and it wouldnt shift it. I do have some footage for a video later in the year.
@stillasgoodasnew
Жыл бұрын
@@ChazzCoombes gotcha, proper seized in there. 👍
@yorkshirelad3332
Жыл бұрын
Hi mate where'd you get that puller from I've searched everywhere and can't find one you can push the bairing back in with
@ChazzCoombes
Жыл бұрын
Hiya, there is a link in the discription to this one.
@yorkshirelad3332
Жыл бұрын
@@ChazzCoombes cool thanks mate
@nevc3968
Жыл бұрын
Hi chazz what size is the kit your using? I have a Mondeo mk4 also cheers mate
@BigGaz00
10 ай бұрын
Would this kit work with a mk3 mondeo?
@kookianneeta
Жыл бұрын
New frnd from amarens
@somanygins.
Жыл бұрын
From amarens. Thanx
@TTisleofmanTt
Жыл бұрын
To get bearing in fully just remove backing plate and press it home using the studs.
@Capt.DPeterson5171
Жыл бұрын
Are you giving out awards? I contacted you and wanted money to send them?
@OverGrowTheUk
Жыл бұрын
Hey mate just changed mine but now have abs light? Any ideas mate
@adamdolezal4898
11 ай бұрын
You broke the abs sensor, forgot to plug abs sensor, you damaged wiring, you did not press bearing far enough so abs sensor could get signal from magnetic ring on bearing…or maybe you just turned ignition on while having abs sensor disconnected and it remembers fault code… There are many options, let us know what it was :)
@OverGrowTheUk
11 ай бұрын
@@adamdolezal4898 thanks for your reply mate, it ended up being a bad bearing Chinese tat lol, changed it out for a FAG wheel bearing and it’s all working great now 👍
@JasonJohnson-yu8zf
Жыл бұрын
You do know you put the nut on the track rod end on upside down? I've bookmarked that bearing tool for future use, 80k on mine I guess I will need it soon
Пікірлер: 42