▶️Link to Mach1 OEM Idle Air Control Valve amzn.to/2KzzGcF ▶️Link to Mustang Gt Idle Air Control Valve amzn.to/2wfW6fY ▶️Link to Mustang V6 Idle Air Control Valve amzn.to/2wfWA5M ▶️ Throttle Body Cleaning kzitem.info/news/bejne/yal9tI2anox9mJg
@chapzer6686
4 жыл бұрын
THANK YOU SOOO SOOO MUCH.... I’ve done everything to no avail I thought it could have been anything from electrical to my mass airflow sensor and nothing worked I’m so thankful man I was about ready to sell my car.
@RANDOMFIX
4 жыл бұрын
Excellent! I'm so glad to hear that my simple video helped you!!! You have made my day, Thank you!!!
@Buttersausage
3 жыл бұрын
I cleaned mine yesterday and it runs wayyy better and smoother
@RANDOMFIX
3 жыл бұрын
Awesome, what were you experiencing before you cleaned it?
@MustangMedic
4 жыл бұрын
Good job man, if this fixes our issue you will get MustangMedic Props to our 55k audience
@RANDOMFIX
4 жыл бұрын
Thanks buddy, I wish you the best and I hope this takes of your issue. If you need help on 94-2004 mustang hit me up anytime. _Randomfix
@MustangMedic
4 жыл бұрын
RANDOMFIX they are a pain in my a$$ and I rarely say that. The sensors and pollution controls seem to be everywhere. MAF and so on...
@ER.Drones
4 жыл бұрын
Thank you for this. I hate videos that go into a million things except the important. You went straight to the point.👍🏼👍🏼
@RANDOMFIX
4 жыл бұрын
Elvin, thanks for the great feedback. Randomfix
@fishingwithsam7526
3 жыл бұрын
thank you brother I'm going to see about that I'm going to do the same thing you did and hopefully it helps me out thank you so much
@RANDOMFIX
3 жыл бұрын
I'm glad the video is helpful.
@vairus0net
4 жыл бұрын
Hey @randomfix ,, thanks a lot for the help. I’m actually planing to buy the part from the link provided in the description but when I checked it on Amazon for my 2002 Mustang GT. The electric connector is pointed straight rather the 90° like the one you have which is exactly like mine. What could be the part number if you can help. Thanks a lot
@RANDOMFIX
4 жыл бұрын
Please reference your own part on you vehicle, it's stamped into the part. Best of luck. _Randomfix
@jamesvotino6125
3 жыл бұрын
Thnx for the tutorial. I'm having an issue with my 04 GT, where the idle hangs at 2200 rpms at start up and when driving, doesn't smoothly rebound while clutching..it rebounds only to about 1100 rpms. Any suggestions?
@RANDOMFIX
3 жыл бұрын
The vehicle is idling at 2200 rpm?
@nietolkj
4 жыл бұрын
I have a 3.8 mustang .i have no codes showing up but the car idles rough. Sounds like a v8. When in park or neutral car sounds slightly rough but wen in drive or reverse it boggles down and engine and exhuast shake. Also takes off slow. U know whats the problem?
@RANDOMFIX
4 жыл бұрын
Alex, sorry for the late response, did you get it fixed?
@nietolkj
4 жыл бұрын
@@RANDOMFIX no i didnt
@savannah328
3 жыл бұрын
I’m having the exact same problem did you ever figure it out it’s so annoying
@nietolkj
3 жыл бұрын
Yes its fixed it was a sensor
@RANDOMFIX
3 жыл бұрын
Thanks for the update. What sensor fixed the issue?
@joshuagoodson6346
4 жыл бұрын
Thanks
@RANDOMFIX
4 жыл бұрын
My pleasure. _randomfix
@allancollins5583
3 жыл бұрын
Thanks 👍
@RANDOMFIX
3 жыл бұрын
Allan, thank you for the feedback 😀 much appreciated
@cmanroxx
5 жыл бұрын
Hey man great video thanks for the upload! I just changed my IAC valve and replaced it with an aftermarket brand (Standard) and it was idling way to high. Wouldn't come down from 1500 rpms. Does OEM have to be the way to go or do you recommend another good aftermarket brand?
@RANDOMFIX
5 жыл бұрын
Christian, thanks for the feedback, I would buy the oem off Amazon because sometime you can get the oem for under $30. Can I get your help? CHECK OUT MY OTHER CHANNEL and subscriber if you like it. THANK YOU ▶️ kzitem.info/rock/-wuhWwzZnFOWK-GMsP6Ejw MANY THANKS _Randomfix
@cmanroxx
5 жыл бұрын
@@RANDOMFIX ok thanks man. And I just checked out your other channel and I subscribed. Real estate is my next business move after I sell my current one. Rock on!
@RANDOMFIX
5 жыл бұрын
Christian, much appreciated brother and if ever need some tips on the secrets of real estate just call or text me, I. Sure you can dig up my number off my real estate channel. Much love and thanks again.
@ChaseKaiser
3 жыл бұрын
So my 02 gt idles really high burns oil let’s off plumes of smoke and sometimes blue. Do you think this could be a pcb valve problem?
@RANDOMFIX
3 жыл бұрын
Do you mean PCV valve? it could be the PCV valve and it's an easy part to change or clean.
@precisiont5188
Жыл бұрын
Does the 2014 Ford Mustang V6 3.7 have that?
@RANDOMFIX
Жыл бұрын
idle air control valve? Most likely, check rockauto.com and in the parts catalog you can double check. IAC or idle air control valve is the name of the part, let me know what you find, sorry about the late response but I'm overseas traveling
@mikebriggs6703
5 жыл бұрын
Hey could give me a few ideas for my mustang and also how hard is it to put a set of exhaust headers on my mustang
@RANDOMFIX
5 жыл бұрын
Mike, for exhaust for mustangs check out americanmuscle.com and if you don't want the check engine light on because most people delete the cats, look into mil eliminators. Let me if need anything else. _Randomfix
@dannyfreeman4065
2 жыл бұрын
Need twin turbo for 5.0 2012GT mustang
@RANDOMFIX
2 жыл бұрын
That sounds nice
@loufernando7617
3 жыл бұрын
My 06 mustang lost alot of power wants to shut off when it turn off but hiccups and stays on and surges when at idle and shakes more at low rpm when it gets hot it gets worse some times dosnt start unless I keep the gas pressed
@RANDOMFIX
3 жыл бұрын
Did you check iac ? Also clean the throttle body.
@viprk24OC
4 жыл бұрын
They will also do described if you dont do the idle set precedure after changing throttle body or intake. Warm the car up leave idling, unplug iac, if the car dies give one full turn on the throttle stop screw and repeat until the car runs but just lower than set rpm.
@robertmurphy8027
4 жыл бұрын
Random videos I’m having this issue. I installed a new IAC valve without going through this procedure and my car starting hanging around 2-2500rpms randomly when I would push the clutch in, until I came to a complete stop.
@RANDOMFIX
4 жыл бұрын
Please clarify a little more, im sorry I didn't follow.
@viprk24OC
4 жыл бұрын
@@RANDOMFIX The Idle set precedure if it isnt set (most people don't even know) It will just keep your IAC wide open to idle or it tries to close but opens back up to continue running (the fluttering in rpm). Find your throttle stop screw it holds the throttlebody open just enough to idle (with or without IAC). Warm your car up. While its idling just unplug your IAC power if the car dies your Throttle stop is too low. 1 full turn to open little more and retry. your aim is to have it close but not over your set idle. After that is all set Unplug your battery for 30 minutes and go through the relearn Ac off idle 15-20 AC full blast 15-20. If you want me to email you a copy of the Ford sheet for it leave your email.
@albertotorres5037
4 жыл бұрын
I have a 2002 mustang convertible that losing acceleration power and can I fix it or what can I do to restore it back..
@RANDOMFIX
Жыл бұрын
Sorry for the late reply! did you find a solution?
@jaredlange4293
3 жыл бұрын
I'm having problems with high idle after starting the car, then once I drive it and it gets up to temp it spits and sputters an looses power. It's a 01 ford mustang 3.8L I cant figure out the problem I have changed cylinder head sensor an MAF sensor
@RANDOMFIX
3 жыл бұрын
Sorry for the late response, any update?
@gabrielmagana2461
5 жыл бұрын
Wasup man have a question, I have this 2001 mustang gt , when I try to punch it the car doesn’t get enough power it start to jerk when I reach 4,500 k rpm what could be the problem , just put a new fuel filter and gas pump work I hear it turning on and off but can’t find what it is
@RANDOMFIX
5 жыл бұрын
Gabriel, first off, do you have any dtc codes? After verify no codes, check your fuel pressure at the rail, then clean the throttle body. This is a super complicated issue and can the cause could be a dirty fuel filter, a bad spark plug or coil, or even low compression. I purchased this 04 mach1 for cheap because the owner thought the motor was blown buy it was a dirty fuel filter. Best of luck and let me know what you find. _Randomfix
@bengordon7635
3 жыл бұрын
My Idle problem was the Throttle positioning sensor and make sure you use OEM parts the china aftermarket parts are garbage
@RANDOMFIX
Жыл бұрын
I appreciate your constructive comments, thank you for the feedback!
@bengordon7635
Жыл бұрын
@@RANDOMFIX also I rebuilt the top end help tremendously on smoother idle and response my engine the exhaust ports were clogged up
@Criselplebe02
3 жыл бұрын
Hey I have a 2003 Mustang gt and when I’m driving it looses power and when I come to a stop it turns off and I got a new battery and it didn’t fix the problem do you know what it can be?
@RANDOMFIX
3 жыл бұрын
Have you already tried clearing idle air control valve? Like I showed in the video?
@Criselplebe02
3 жыл бұрын
@@RANDOMFIX no actually I’m gonna do that today because it doesn’t idle properly and would you need to buy a new gasket
@RANDOMFIX
3 жыл бұрын
Okay, I had the same exact issue on gt and mach 1 mustangs. This fixed it.
@Criselplebe02
3 жыл бұрын
@@RANDOMFIX okay thank you imma have to try that
@Criselplebe02
3 жыл бұрын
@@RANDOMFIX I did it Rn and it didn’t work it shuts off now super fast idk wait it can be?
@realtruthseeker521
4 жыл бұрын
I have 2006 automatic GT. Does it matter if its stick or auto? I was having erratic idol at stop signs. I changed a coil misfire. Then I cleans my MAF SENSOR. but should I check this sensor?
@RANDOMFIX
4 жыл бұрын
yeah, i would clean or replace ( depending on the miles and mile) the iac (file air control valve)and clean the throttle body. You can do it at the same time. After that if you still getting a off idle I would do a cylinder miss fire test using a $60-500 scan tool and it will tell you what cylinder is missing. Lastly you have a vacuum leak. Best of luck and let me know what you find. _Randomfix
@realtruthseeker521
4 жыл бұрын
RANDOMFIX cleaned throttle body and it took care of the lag in acceleration and the idle is better. I went on a 50 mile drive to let it all reset. I still feel a miss every once in a while but it was at every stop before the cleaning. Throttle was very dirty. But now when I shut the car off the is a flank sound as it shuts off. Sounds like a hard sound like I guess “clank” is bets way I can describe. It did t do that before. Possible timing issue when shutting down as if something is a little out of time
@realtruthseeker521
4 жыл бұрын
RANDOMFIX Thanks for the reply.
@Buttersausage
3 жыл бұрын
I have a 95 mustang gt it has the stock exhaust what upgrade would you recommend with out spending to much?
@Buttersausage
3 жыл бұрын
@randomfix
@RANDOMFIX
3 жыл бұрын
I would recommend a h pipe or x pipe. I personally ran my h pipes without cats ( sounds sweet) but that maybe challenging certain states like California. Good luck and enjoy
@THECALIKING
3 жыл бұрын
You shouldn’t leave the iac on it’s side when you blow the cleaner in it. The liquid will go into the motor and harm it.
@RANDOMFIX
3 жыл бұрын
That you the feedback and I will note your feedback on future videos
@fallenangel4828
3 жыл бұрын
Please tell me what you think! I have a 2018 Mustang Premium Ecoboost. 70k miles. A year ago it randomly stalled at a light and never happened again. Last week, I was at a stop light and heard a weird noise and noticed my car started idling low and choppy. I hit the gas kept driving but the loud noise persisted and I pulled over. When I pulled over it stalled completely would not turn over. I called someone to come get my three kids because it was hot and my car was not going anywhere. 20 mins later my car cranks and drives fine but has a check engine light. I parked it and two hours later it cranks, no engine light, no problems. One week later (today) I fill my gas tank up and tried to start, it tried to turn over but wasn’t. After the third or fourth attempt it finally turned over with very low and choppy RPM. It continued to try to stall and after 5 minutes of lightly pushing the accelerator, it fell to a low RPM and seemed to adjust itself and was able to drive it home. No engine light on. I am waiting to take it into a shop. What should I check?
@RANDOMFIX
3 жыл бұрын
Scan it will obd2 reader and it may have recorded the code.
@fallenangel4828
3 жыл бұрын
@@RANDOMFIX thanks!
@RANDOMFIX
3 жыл бұрын
Also check carcomplaints.com and see if others have had the same issue and this can save time and money.
@fallenangel4828
3 жыл бұрын
@@RANDOMFIX thank you so much! This was a big help. I found out Ford Mustangs are well known to have this problem. It needs an evaporative purge valve. Codes were P1450 and P1444
@RANDOMFIX
3 жыл бұрын
Glad to help and thank you for letting my tip helped you. KZitem is a great community for this reason.
@eddiehardy8497
4 жыл бұрын
Hey thanks for the video man. I recently bought a 04 mach 1 and I made a mistake a put the wrong fuel in it. Now it idles rough and loses power when I hit the gas. I’m not sure if it’s the fuel filter or MAF?
@leodavalos8451
4 жыл бұрын
I would replace both
@RANDOMFIX
3 жыл бұрын
Eddie, did you figure it out.
@xx_cowboy_xx5228
3 жыл бұрын
Cleaned my throttle and got a new IAC and the idle still hunts or is too high
@RANDOMFIX
3 жыл бұрын
so is the idle high or low? Did you clean the mass air flow sensor with mass air flow sensor cleaner? Last I would check for intake leaks.
@xx_cowboy_xx5228
3 жыл бұрын
@@RANDOMFIX when I start the car it’s at like 1300 then takes 2 min to go down then it hunts at 500-900. Ig I’ll check those two tomorrow
@RANDOMFIX
3 жыл бұрын
Okay, keep me in the loop
@xx_cowboy_xx5228
2 жыл бұрын
@diane Taylor hey So I ended getting my engine replaced. So I’m not entirely sure but I do know they my MAF was starting to go bad. So that might what it was
@xx_cowboy_xx5228
2 жыл бұрын
@diane Taylor I’ve got the mach 1 so it’s dohc 4v But the price fluctuates depending if you do it yourself or a shop but I’d say 4K-9k
Пікірлер: 90