On the conversions I've done to Petronix, on tractors or automobiles, I always use their wires as well as their suggested flamethrower coil for the electronic ignition system. Never a failure. Good test procedure on the coil my friend.
@ModelARickLasCruces
15 күн бұрын
Great info; going to test the spare coil I have for my 1931 Ford Model A.
@Building_Bluebird
Ай бұрын
Those damn gnomes created infinite Ohms.
@kennethtalbott2233
9 ай бұрын
those blinking gnomes.....
@rodritz8384
Жыл бұрын
I don't think the secondary winding is connected to the primary winding. To test the secondary you have to connect from the center terminal to the body of the coil which is grounded by the mount.
@TheKiltedHomesteader
Жыл бұрын
Trust me, this way works!
@ianrobinson9565
4 ай бұрын
Lucas coils. The Secondary winding is in series with the Primary. Why? This improves the spark at the plug. The 300 volts induced in the Primary at the contact break being added to the Secondary voltage. This effect is known as auto transformer action. Now, please take note. A standard Lucas wet (oil filled) coil is 2.7 ohms. Work on 3 ohms, but check current. On 12V you are looking for 4 AMPS. This is a standard coil without an external resistance. Remember that Lucas coils are wound for positive ground which is negative spark. Don't try running negative earth. Yes it will work for a while, but you must have a negative earth wound coil.
@ianrobinson9565
4 ай бұрын
Also the centre terminal of the coil is grounded by the spark plug. The case is fully insulated from both the primary and the Secondary windings of the coil. If you get a reading through the case then you have a faulty coil. Hope I haven't confused you too much. 😊
@benitocamela8541
Жыл бұрын
My primary show 5 ohms but secondary shows infinite. Does that mean the coil is bad?
@Electric-Bob
Жыл бұрын
Yes
@RussellMcChesney
8 ай бұрын
How do I know if my coil has the internal resistor or not?
@TheKiltedHomesteader
8 ай бұрын
By getting the makers specs. Usualy a part number can help.
@marioncobaretti2280
Жыл бұрын
I have to find a nomes equipped meter
@TheKiltedHomesteader
Жыл бұрын
Let me know if you find one ; D
@Electric-Bob
Жыл бұрын
Its One Point Ohms... Not Point One Ohms Resistance showing on the Meter, Sir. People... ALWAYS Purchase an AUTO RANGING Digital Meter! Harbor Freight GIVES THEM AWAY!!
@TheKiltedHomesteader
Жыл бұрын
Thanks for the info.
@anthonywbelcher
Ай бұрын
Well done, a great video showing how to test a coil. A simple explanation that even I could understand. Thank you.
@do6724
10 күн бұрын
Wow, great video! I am having an issue with my car. It misfires when it’s gets warm and looses all power. Narrowed the problem down to ignition. I will test the coil as you described. Thank you!
@Eli-lx2fq
6 сағат бұрын
You,friend have a short between the steering wheel and driver’s seat.😂
@plcreman
2 жыл бұрын
There is no internal resistor. The resistance of the coil is determined by the length of the wire, the diameter and the composition of the wire. Thinner wire with more turns will read higher than thicker wire. Shorted turns will cause low resistance as well as. A static resistance test is ok, but a better test would be a ring test or better yet an inductance test compared to a known good coil. A small resistor in series is not a bad idea on either coil as of the key is left on and the contacts are closed you have continuous current flowing through the coil and creating heat. Once the points are interrupting the current flow you are getting an AC pulse and this is where inductance and inductive reactance (resistance) comes into play. The higher the RPM the higher frequency of the pulse and the more reactance. Overall the video is a good basic test.
@TheKiltedHomesteader
2 жыл бұрын
Thank you for the feedback! All information is greatly appreciated.
@captainschannel9331
4 ай бұрын
😎
@24-Card
5 ай бұрын
“The coil never goes bad.” I have replaced MANY, same with the condenser!
@dustytrailswithepa
Жыл бұрын
Great video my Friend !
@robertpeacock5515
Жыл бұрын
You need to move the ohmeter resistance to 20k for second test.
@TheKiltedHomesteader
Жыл бұрын
Why is that?
@The13thSword
Жыл бұрын
@@TheKiltedHomesteader Because in general, the secondary circuit on an ignition coil will be in the range of 6000 Ohms to 16,000 ohms, depending on the coil's original specification. The Primary circuit should be tested on the 200 Ohms setting on the meter. Same reason. Coil Primary circuits in general will range between 0.2 to 3 Ohms, again depending on the coil's original specification. Just my experience but electronic ignition modules (Pertronics, GM HEI, etc.) don't play well over time with higher resistance on coil Primary circuits. I've learned from research (and from actual doing) that most electronic ignitions that use a Hall Effect signal generator in the distributor work better & longer if the coil Primary resistance is 1.5 Ohms or less. Ideally (at least as far as HEI modules are concerned, Pertronics is similar, depending on model) 0.2 to 0.8 original specification for Primary resistance is best. If you look at Pertronics own website & check the coil Primary specs on their later-model Flame Thrower 2 & 3, they are in those lower ranges. I found it very interesting that both your Primary & Secondary circuits went "open' at the same time. I've never come across a coil that did that. They most usually develop high Secondary resistance over time or the Secondary just goes "open". That's mostly due to time, heat, & the fact that the Secondary can put out 20,000 to 50,00 volts. That's a lot of stress over time & it will break down eventually.
@TheKiltedHomesteader
Жыл бұрын
@@The13thSword thank you for the information!
@t.h.o.r.
6 ай бұрын
@@TheKiltedHomesteaderbecause the resistance is much higher and needs to be measured on a higher scale.
@icannevergetthistowork
Жыл бұрын
Great video. My tractor just quit on me this morning. Checked everything and then found your video. It was the exact same problem. Thanks for your help!
@TheKiltedHomesteader
Жыл бұрын
That’s awesome! Thank you for watching.
@timgroleau1612
Жыл бұрын
I don't believe there is a resistor in the coil. The resistance reading on the primary should be under 1 ohm, because there is a small amount of coiled wire compared to the secondary. To test the secondary. Move the meter to 20K ohms. The secondary has many more coils of wire and would have much more resistance, it should read 5k to 10k on many coils. General rule.
@TheKiltedHomesteader
Жыл бұрын
Yes, some coils have built in resistors and some do not. They make them both ways and for different applications. Thank you for watching.
@acecraige6419
4 ай бұрын
KAL BO OOO,---SUPUTTT,!!!!
@robertbarnhardt9792
7 ай бұрын
Why all the bs just what is the value of the coil 2 min video
@TheKiltedHomesteader
7 ай бұрын
Thanks for watching!
@patrckgann1438
4 ай бұрын
Should have named the video the impotent nome!😂
@TheKiltedHomesteader
3 ай бұрын
lol
@coltonwillie-wp3wk
Жыл бұрын
That was the best example I have found thanks!
@TheKiltedHomesteader
Жыл бұрын
Awesome and thanks for watching!
@Peter-od7op
Жыл бұрын
I have ford 3000 tractor it dies at 1400 rpm any ideas
Пікірлер: 44