Thank you for this. I am currently doing this job on a customers Transit. Word of advice - if you're replacing the blower motor, go OEM if possible. The one I got from Napa doesn't have large holes in the cash allowing a person to reach through it and aid in installing the new motor. I've been fighting it for over an hour now with help from a coworker... Not fun. My back & shoulders are killing me 👎
@cybersfn7678
7 ай бұрын
I took on this job, wasn’t terrible(mind you I’m a pretty skinny dude ). My blower wasn’t the issue, turns out there was a bunch of leaves and trash built up in the motor causing it to rattle. Thanks for the video helped a ton !
@miekolock4060
9 ай бұрын
I am SOOOOO not looking forward to this!! But thank you so much for the video I can only imagine how hard it would be to go in blind to this one. And figure out all those small details one problem at a time.
@drummerpenguin2970
4 ай бұрын
Best tutorial out there for sure
@johnnysmythe2552
Жыл бұрын
thanks, i was pulling my hair out with the instructions in alldata pro
@rashonmckinney1872
8 ай бұрын
Best video I have since yet
@richardlegere224
Жыл бұрын
I'm about to start mine... can't wait 👍😂
@trashpandaoutdoors772
2 жыл бұрын
Anyone wanting to do this job and has the mindset can do it. Remove the drivers seat. This aided me in unplugging the blower motor, prying the release tab, and clocking the blower motor back in place (plugging it in too). Passenger side- remove the panel on the side that faces the door. Helps you see the second screw. Third screw is completely out of sight. Use your phone on video mode. Apply pressure to the screw keeping it against the cage and remove the cage and screw as a whole. Do the tape method on assembly. I set the blower motor in on the passenger side but twisted it into place on the driver. (Get in the cab with your legs to the back and look up) way more comfortable.
@rashonmckinney1872
8 ай бұрын
He just explained all this to us
@jcwick0859
2 жыл бұрын
this job is a real pita... the hardest part is getting those 3 torx out... i like that idea of the boroscope wish i would of saw your video earlier... but what i did to get the back 2 screws i layed across the front seats and was able to peek with a lil bit of difficutlies where the screws were u can barley see them but was able to get an extension with my torx and remove them.. to put them back u can use a piece of a rubber glove and shove the torx screw on the torx bit it will hold in place and u can put them back the same way u took them off... its not easy but it can be done that way... make sure u have good lights to see where they go its a bit dark under there
@frankortolano5886
Жыл бұрын
Excellent. Excellent video thank you
@ram89572
27 күн бұрын
I sincerely hope the resistor is what i need to change because that doesn't look like a cheap job on my van woth a rhd conversion in the way
@ram89572
22 күн бұрын
So I managed to change the resistor today with the help of a friend a lot skinnier than me. Still didn't fix my problem sadly. Took us 6 hours just to do the "easy" task of the resistor. The motor is going to be absolute hell I guess. Gonna need multiple days I think. Going to have to take my rhd conversion stuff out of the van. Probably remove the passenger seat (driver seat is already removed with a mail tray in its place. Really the brake pedal needed to come out as it was in the way today. And the whole dash needs to come out to have any access worth a crap.
@hobotalk2834
13 күн бұрын
Keep a positive mindset during these repairs. methodically removing parts keeping everything orderly and clean as you can. I believe you will be fine.
@TheReason101
5 ай бұрын
Probably saved me $300-$500
@serafinhernandez5436
Жыл бұрын
Good explain.
@jeremymayer4223
2 жыл бұрын
Thank you!
@keithdombrowski8212
6 ай бұрын
Second time doing it. Let’s go! I just had to brush back up on the steps. This job sucks!
@melvinyosten3776
2 жыл бұрын
Wow after watching you struggle with that, I don't want anything to do with that crap
@NoflectioN
Жыл бұрын
Thanks for the video!
@festerfm
Жыл бұрын
Is it not possible to push that tab and turn the motor all on the driver's side?
@RandySlim76
2 жыл бұрын
And to think I was complaining about changing a heater core on a hard body
@Pssnmeoff
2 жыл бұрын
Any tips on reinserting the hidden screws?
@hobotalk2834
2 жыл бұрын
Remove the part and tape the screws in place, then gently put part back in place with screws taped in place. I show some of that in video. Thanks for watching good luck
@Jeffmtbr
2 жыл бұрын
His best advice is the tape trick, I used a "sticky putty" but still lost the bottom screw. I also did use a borescope. The whole job sucks.
@Wickedstickyflowers
2 жыл бұрын
F$&@ing A
@Pssnmeoff
2 жыл бұрын
The painters tape wrapped on either side of the hole helped a ton. I had to do this entire job -2x- because the first one I put in didn't have the foam gasket inside the sealed box. Thanks NAPA... The game changer for doing this whole thing was switching screws completely. I bought 3/4" #6 Hex head self drilling screws and hand drilled them right into the body of the unit in the same holes. Essentially rethreaded the holes with screws that I didnt have to worry about the bit popping out of. I drive them in with a magnetic sleeved Dewalt bit holder ($6 @ Lowes) with a ratcheting right angle screwdriver ($3 from Harbor Freight). The driver itself fit perfectly over the screw, held in place with them lightly poked through the tape. So you can easily just do it by feel. The second time I had to go in and redo it, it was waaaay easier to remove and replace. Rest of the job was shitty though, but TRY IT.
@samuraibeck
2 жыл бұрын
Only problem is I don't have the "other guy" to take the blower motor out
@SrColon309
2 жыл бұрын
OMG a lot of work. I don't think I can do it.
@peteyhop7589
Жыл бұрын
Definitely not doing this job myself
@VaSKovach
Жыл бұрын
Another reason why not to take Ford Trush. Not worth the hustle.
Пікірлер: 41