**Motorcraft Ignition Coil Set DG508: amzn.to/2s6nbQU **Motorcraft Spark Plug SP493: amzn.to/2D99jrB If this video has helped you out consider donating to the the channel with Paypal, thanks! www.paypal.me/ozzstar
@CubasAutomotive
4 жыл бұрын
100% ONLY motorcraft or OEM on these. Aftermarket does not last long or sometimes doesn't act right altogether on these. Just do it right & use quality parts the 1st time!!
@ebhsports6251
4 жыл бұрын
Yeah, I've got a 2000 E-350 5.4L missing on 1 & 3 . I'm just going to change all 8 plugs and coil packs. Good video. Very helpful. Appreciate it.
@ozzstars_cars
4 жыл бұрын
@@ebhsports6251 good luck with the fix and thanks for your comment.
@martinquinones9847
2 жыл бұрын
Are this parts on the link oem parts for a 08 e250
@mikehunt6218
Жыл бұрын
I watched five of these videos today and this was by far the most comprehensive one. Great job 👍
@karentroyer3011
Жыл бұрын
You have the clearest instructions of any video I've ever seen. I appreciate you're honesty about the difficulty level ex. having to do things blind & the tools you've laid out before hand. You are the only one that has been actually been helpful by just sticking to the task at hand & not muddying it up with a bunch of unnecessary bullshit. P.S. be sure to video the next time you do a repair from start to finish so we can see the actual process in it's entirety. Thanks
@ozzstars_cars
Жыл бұрын
Thanks for your comment. I appreciate your honest and straightforward feedback. I do have about 320 repair videos. Filming an entire repair from start to finish could cause some people to fall asleep. 😂
@diymisfit_Mechanic_UDX404
4 жыл бұрын
I really enjoyed this video, because I wasn't the one changing those plugs. 😁
@ozzstars_cars
4 жыл бұрын
🤣😄🤣
@wyattoneable
4 жыл бұрын
I like what Matt said. I hardly ever accepted work on a van in my day. And now I'm just not that flexible or skinny. But the video isn't about me. :) You did a great job taking on that job and showing all the steps.
@ozzstars_cars
4 жыл бұрын
Some of those cylinders were a real bitch to get at. Cylinder 4 was cake.
@malukens
3 жыл бұрын
I just replaced all 8 plugs on my 2013 E350 and this video was a huge help! I was able to remove and replace all 8 plugs from inside the vehicle with little trouble. I will say that taking the extra 15 minutes to remove both front seats was a huge time saver as it made it much easier to reach all of the coils and plugs. I did remove the PCV valve hose as it was routed over plugs 2,3 & 4 as well as removing a bracket that held some other vacuum switch on the back of the intake plenum. I was careful to hand tighten all 8 plugs (about 8 turns) before putting a torque wrench on each one to get the torque set consistently at 11-14 ft.lbs. Overall it wasn't as difficult as I had suspected, about 3 hours of works at a leisurely pace.
@ozzstars_cars
3 жыл бұрын
Glad the video was helpful thanks for sharing your comment Mark.
@keldonator
2 жыл бұрын
Glad to hear a time. I was dreading this but 3 hrs isn't too bad.
@coreybabcock2023
Жыл бұрын
I can do all 6 in my 98 Ford e250 in about a hr
@invitro1432
Жыл бұрын
Best and most simply explained video on these vans I’ve seen yet! Thank you.
@ozzstars_cars
Жыл бұрын
You're welcome
@virtue7789
10 ай бұрын
Tools mentioned: 3/8th ratchet 5/8th spark plug socket, 6 inch extension, 1 inch extension, Shorty 3/8th ratchet For coils: 1/4 6 inch extension 7mm socket. Someone mentioned removing other things from the seat to some brackets inside, Another mentioned using a compressor to remove debris! Hope this helps!
@mxt4907
7 ай бұрын
Thank you! For the extensions, what do i look up? 3/8th ratchet extensions? I’m a bit of a newb
@nixonkutz3018
3 жыл бұрын
Excellent video, thanks for making it. Exactly the information I needed with no fluff.
@kevinbarry4325
Жыл бұрын
Good job dude.explained well. I brought my Econoline 250 super duty 2007 to mechanic I had 6 misfires he said he replaced spark plugs bla bla $578.00 my truck now runs much, much worse the CK engine light blinks now, he had it 5 days. A tree fell on my Lincoln last summer, crushed trunk,blew out back window. I went to junk yard got trunk,rear window did all but paint it. Even body shop F**** UP letters. I don't trust ANYONE!!! what the hell happened to competency?? I am a contractor 30 yrs. I do my best for every customer. I will fix this Van MYSELF! thankfully people like you help us MEN out here to fix our own things. I also put a starter on my Lincoln myself. Thx again keep up good videos!!
@ozzstars_cars
Жыл бұрын
I know what you mean Kevin about incompetent people, and lately it's real bad! A flashing check engine light is a misfire and that's not good. Hopefully you can figure out what's wrong and make it right. Let me know how it goes. -Glen (Ozz)
@CubasAutomotive
4 жыл бұрын
Great job showing the details of what's entailed in doing a tuneup on these. I always enjoyed these myself, E or F series vans & trucks. Not many ppl like working on them, but I'll take them all day. Small hands and being able to perch myself up on the engine bay works out well for me. Lol. Take care Glen!
@ozzstars_cars
4 жыл бұрын
Once the economies of scale kicks in all you can do is keep winning! Thanks Cuba.
@drainmonkeys385
4 жыл бұрын
Cuba's Automotive schwing!
@jtanzella
Ай бұрын
Finally someone who shows you the Meat and Potatoes of the job! You told me everything I need to do in 10:42 seconds! Thank you. There are videos that are ridiculously long and waste so much time. Again, thank you.
@ozzstars_cars
Ай бұрын
@@jtanzella to the point with true facts is how I roll. Thanks for the comment. -Glen
@spelunkerd
4 жыл бұрын
People wonder why mechanics have so many tools that seem to do the same job. It's all about access. Nice demo!
@ozzstars_cars
4 жыл бұрын
It sure is.
@kevinobrien7529
4 жыл бұрын
Your filming was very good. Possibly the best that I have seen. Thank you for the video
@ozzstars_cars
4 жыл бұрын
I appreciate that Kevin. Making videos takes a lot of hard work and time. Take care. -Glen
@traviswilson9198
Ай бұрын
I agree with color JT Zeller or whatever it is you are very thorough very easy to understand way to go dude keep up the good work
@darhopkins5433
2 жыл бұрын
Coming to this in 2022. EXCELLENT video and it's so refreshing to see and hear it done in such a professional manner. Hats off to you and God bless, my friend.
@ozzstars_cars
2 жыл бұрын
Thank you sir!
@carakintz3536
2 ай бұрын
Thank you for covering vans, van videos are RARE!
@ozzstars_cars
2 ай бұрын
Awesome!
@carakintz3536
2 ай бұрын
We need a good reliable van, for camping and daily driver. Hopefully we can find an Econo box with low miles for under $10,000
@johnmathews7305
3 жыл бұрын
Thanks so much, I had an estimate of $1,200 to replace all of my plugs and coil packs-don't think so! I've never really been an auto mechanic type but with KZitem and guys like you, I can do this and save a bundle. Thanks.
@ozzstars_cars
3 жыл бұрын
You are welcome John. Take your time and be patient as you work. Good luck with the fix, use OEM parts pinned above in the description and you should be good to go for a long time.
@uski59
3 жыл бұрын
A $1200 fee to change plugs ?.... Wow what a thief.
@gadgetsage
2 жыл бұрын
@@uski59 well, each of those shit Ford coils is $80x8 from dealer, so there's $640 right there, plus plugs, labor, that might include plug/ignition wiring, etc etc etc so yeah. Still sounds crazy high, I think mechanics are gonna be rich for a while thanks to burdens mandates fucking everything up...
@stuzman52
4 жыл бұрын
Great job in explaining how to get those plugs and coils out! I'm sure the information will help a lot of folks out there. Oh, by the way, one of my brother's nickname is Dookie. Have a good one Glen!
@ozzstars_cars
4 жыл бұрын
Interesting nickname, did you give him that one? 😄
@MattHeere
4 жыл бұрын
How do you make an otherwise simple engine a giant pain in the butt to work on - put it in a van!
@ozzstars_cars
4 жыл бұрын
Ain't that the truth Matt! #vanlife
@RustyZipper
4 жыл бұрын
#How to keep dealerships in business! 💰
@invitro1432
Жыл бұрын
No wonder the newer styles have truck front ends rather than the bulldog flat nose.
@JohnnyDS6557
Жыл бұрын
Great video, thank you. Your camera work was good and left a clear field of view. I would add to make sure you blow out the area of the spark plugs after you pull the coil boot. Then blow it out again after you start turning the plugs out. You don't want anything falling down into the cylinder. I even go so far as to stick the compressor wand down into the spark plug hole and blow out the cylinder just before I install the new spark plug. You really don't want any junk going into the cylinders.
@ozzstars_cars
Жыл бұрын
That's a lot of blowing. Good idea.
@KS-ep1vr
Жыл бұрын
Thanks for taking the time to show this. What a great video! Im a DIYer. Just bought a second hand 2004, 4.6L E250 with 220K miles. She runs beautifully and I want to keep it that way. When i removed the doghouse to look at the sparkplugs I couldn't believe how packed that engine space was! How does anyone reach in there? Thanks for the tool tips as well
@ozzstars_cars
Жыл бұрын
Van engine work certainly isn't the most fun but is doable. Thanks for the comment KS!
@wgibson86
3 жыл бұрын
Thanks brotha! I was staring at that fuel rail thinking how am I gonna do this?? This helped get me straight. Swapped out the coil in no time and now my RV is running smooth. Not sure what the repair cost would have been but sure it saved me some $$. Great video and thanks again!
@ozzstars_cars
3 жыл бұрын
💯👍
@SailProMarina
6 ай бұрын
To do Cyl #1 did you do it from inside or from under the hood ? And does Coil pack on Cyl 1 also 'bend' out of the way to remove without removing fuel rail ? Help !! thanks.
@4twowildkittycats
3 жыл бұрын
Thank you handsome. I have a miss so I'm gonna go replace them all since I don't have a scan tool. I bought the 2004 e250 about 3 months ago for $2,800 has way alot miles 273, 000. I know I should have waited but I was so tired of looking. It ran great. Air works, and i drive it everyday to work. I changed its oil & filter & air filter myself It doesn't like hills very much but apparently it's common with this year. But for some reason the battery was dead and I think it was the terminal hopefully. I cleaned it but it still messed up cause I haven't drove far enough to charge. The idle is rough big time., but it idles better when I turn on A/C. I work alittle on vehicles so Im gonna ck vacume hoses and replace sparkplugs. I plan on taking good care of this old van cause it's soon to be my home. I tore out all the metal shelving which was a pain for me I even had to cut some parts out with my grinder. I now have hardwood floor, frig/freezer, fake but looks real wood stove heater. My bed a fold down desk and some other things. Its cozy. I will do a video eventually. I just hope I can get to know my motor well so i can take care of her. I hope the plugs work and there's no more miss in the idle.I just decided I'm gonna put semi expensive sparkplug wires. Anyone have a van like mine?Which boots and wire set do you think is the best for this old van???
@ozzstars_cars
3 жыл бұрын
If you watched the video you know that there are no spark plug wires, they are coil over plug design. #vanlife
@24allnightmike
Күн бұрын
Great job on this project!! It helps me a lot!!!
@ozzstars_cars
Күн бұрын
You're welcome!
@drainmonkeys385
4 жыл бұрын
I’ve got an E250. 2012. 365,000 miles on it...still runs good... I did change out the plugs and coils .. all of them at about 230,000 miles and I had to change out a couple sensors a while back... I had to replace ball joints and tie rod ends..and that’s about it.. nothing else except brakes and calipers ..... do your maintenance and drive responsibly and you’ll get a lot of life out of those vans
@ozzstars_cars
4 жыл бұрын
That's good advice for any vehicle. Thanks for the comment.
@tomtang5649
4 жыл бұрын
Hi Robert, I had Ford E250, it's show codes P0307 and P0316. how can i find parts number and diagram? Thanks
@tk5680
Жыл бұрын
This is definitely the best video on this vehicle on KZitem. Thank you!
@ozzstars_cars
Жыл бұрын
Thank you TK!
@Angelum_Band
3 жыл бұрын
I love the way Ford builds and designs everything so midgets can be hired to do the work.
@ozzstars_cars
3 жыл бұрын
😂🤣😂
@jdlivepro
2 жыл бұрын
so he just shows you the easiest one. I just did this side... 1-4 last week & #2 was pain. the other 2 were harder than 4 as well. I'm gonna start 5-8 today or tomorrow. I'm concerned about that fuel line blocking #8. talks about the other ones but doesn't show how to. Can't complain tho.. this video helped me get started.
@ozzstars_cars
2 жыл бұрын
That's because it is nearly impossible to film the other cylinders. He talks about that in the video. You must e one of those video watching skipping guys? If you would like to sponsor him he would be glad to show you how the other 7 plugs are changed out. Oops, I mean sponsor me.
@jaygold4467
2 жыл бұрын
You need to blow out the spark plug port before you take the spark plugs out in order to stop any debris getting down in the cylinder port. Very important.
@ozzstars_cars
2 жыл бұрын
That's always a good idea.
@jdlivepro
2 жыл бұрын
yep
@coreybabcock2023
Жыл бұрын
I should do that next time
@tomethen2489
8 ай бұрын
I'm amazed at this video. I watched another video about the same thing and this other guy said he had to remove both fuel rails. You mentioned nothing about removing all the stuff he did. I have already dealt with the #4 coil and plug and really want to do the rest. I hope it's just as you described it without removing the fuel rails. I hope you will reply with the answer. Thanks for the heads up.
@ozzstars_cars
8 ай бұрын
As I said in the video, pull up on the coil to release it from the sparkplug then bend slightly outward and up. No fuel rail removal is necessary in this case.
@cpaluissanchez
Жыл бұрын
mine has a damaged coil and I already bought all 8 of them and the sparks....wish me luck as I have never done it before. thanks for the video! 🙏
@ozzstars_cars
Жыл бұрын
Be patient and take your time. It's a fun challenge! Good luck.
@Nacturnal702
2 жыл бұрын
1995 Ford E-150,Took the carpet off passenger side, checked all under side for wires ,or lines,,,,, took a reciptackle saw, with a millawake steel cutting saw,, and cut the floor 3,6 inches,grabbed some channel locks pulled the steel floor back so i could reach 1,and2 spark plugs, also pulled the passenger tire off and used extensions , with a 1/2" driver, got everything off, took some finesse and time, but got it done
@DanielJaegerFilms
4 жыл бұрын
Good for you using Motorcraft parts. We have a fleet of Ford E-series shuttles and it seems the only ignition coils which last are Motorcraft.
@ozzstars_cars
4 жыл бұрын
I use OEM parts when possible. Doing the job twice sucks especially when it's someone else's vehicle.
@jodywhitedrums
2 жыл бұрын
I’m learning this lesson currently. Replaced all the plugs and coils back in December. The mechanic used cheap aftermarket coils. 2 have gone bad in 10 months. What a pain.
@kinotroikgames2818
7 ай бұрын
Thanks man! This was super clear and helpful! I’m going to be trying to change the coils, spark plugs and possibly fuel injectors on my 08 van!
@theartofplumbing
11 ай бұрын
Great video. Thank you. Your video was the best one out there for what I needed to do. You save me big money.
@ozzstars_cars
11 ай бұрын
Keep that work van working!
@valerietaylor8299
5 ай бұрын
Very helpful thaking God fir you I'm attempting to replace my number 1 it failed emissions that's the only plug the diagnostic showed was faulty
@ozzstars_cars
5 ай бұрын
The #1 cylinder is famous for misfiring, many times due to the intake manifold cracking and leaking into the sparkplug tube. Check for wetness! Good luck and let us know what you find.
@jeffoff7795
2 жыл бұрын
Great presentation. Easy to understand. I have a misfire on cylinder 7. I got everything cleared out of the cab and I rearranged the tools in the back so I was able to push the seats back and hopefully that'll give me enough room to work. I'm going to attempt to tackle it this morning.
@ozzstars_cars
2 жыл бұрын
Sometimes laying on your chest and working while laying on the floorboard gets the job done.
@KS-ep1vr
Жыл бұрын
How did it go?
@jeffoff7795
Жыл бұрын
@@KS-ep1vr Very smoothly.
@guycortesi
2 жыл бұрын
Thanks for taking the time to record and post this. Much appreciated and clearly presented.
@ozzstars_cars
2 жыл бұрын
Thanks for your comment Guy!
@kirbyconner9952
2 жыл бұрын
I'm getting ready to try to do my 06 e350 until I watched your video I said no way after looking under the hood. Thanks for your video
@ozzstars_cars
2 жыл бұрын
A smart man knows when to say when.
@jimthecarguy
4 жыл бұрын
Good job Glen. Those van are really a pain in the rear end to get the front plug out and of corse back in without cross threading.
@ozzstars_cars
4 жыл бұрын
You know it Jim, all fun stuff.
@snphvincent9388
4 жыл бұрын
The camera angles and focus were good bro. The lighting is very good.
@ozzstars_cars
4 жыл бұрын
Thanks, I try the best I can.
@letusdebatenow
3 жыл бұрын
Appreciate you taking the time. Gonna save me a couple hundred bucks
@ozzstars_cars
3 жыл бұрын
You're welcome Ryan. Take your time and have fun.
@tima982
Жыл бұрын
Thank you so much for detailed video now I feel confident to replace coils on my e350 Once again thank you 😊
@ozzstars_cars
Жыл бұрын
Best of luck!
@PaulysAuto
4 жыл бұрын
Oh yeah I love me some Ford work all day! Great tips Glen...sorry I've been neglecting your videos as of late man. I'm catching up with everyone out there. Having wobblies, a good assortment of various length extensions, and some good flexhead ratchets are a must on these types of jobs for sure! Thanks for sharing this Glen!
@ozzstars_cars
4 жыл бұрын
The right tools for the job makes life easier. It's a busy time of year. I am way behind on vid watching as well. Take care
@JohnnyBuschi
2 жыл бұрын
I just had to change a coil on my 5. This video helped a lot. Thank you.
@ozzstars_cars
2 жыл бұрын
Good news, you're welcome Johnny!
@zjames1324
Жыл бұрын
Thanks for the video man this was very helpful! I ended up torqing to 22lb, worried about them blowing out.
@ozzstars_cars
Жыл бұрын
Vans with 4.6 and 5.4 L don't have that problem, they are 2 valve engines, not 3 valve.
@marcsalcedo2056
Жыл бұрын
Thank you for the straight forward direction.
@ozzstars_cars
Жыл бұрын
You got it!
@ss66chevy
3 ай бұрын
Great video. I really appreciate the detail instructions.
@ozzstars_cars
3 ай бұрын
You're welcome. -Glen (Ozz)
@zacriah85
Жыл бұрын
Exactly what I needed. I step-by-step walkthrough. Thanks!
@ozzstars_cars
Жыл бұрын
You got it Zach!
@MrNathaneasterling
Жыл бұрын
Great video, thanks for posting! Now I feel a lot better about changing mine out.
@ozzstars_cars
Жыл бұрын
Awesome!
@clintonearlwalker
3 жыл бұрын
I have to say I "liked" your video, but I can't say I "enjoyed" it. I got a 2000 E-150 van with the "service engine soon" light on and it's apparently had these coil on plug problems before. My dad took it to a garage, but I see this job coming in my future, I'm predicting a LOT of cussing. Thanx for the video.
@ozzstars_cars
3 жыл бұрын
After you do this job a couple of times it's almost easy. Have fun and don't forget to put your money in the swear jar. haha
@adambergendorff2702
2 жыл бұрын
Excellent video! looks easier than I expected, now that I've seen your video!
@ozzstars_cars
2 жыл бұрын
Appreciate your comment.
@drewvogel9330
11 ай бұрын
Dude you took the easiest. You want to show some knowledge. Show me how to get number two out under the fuel rail in the vacuum lines and heater hose
@ozzstars_cars
11 ай бұрын
It's impossible to get a camera in there to film number 2. I can change that plug out in two minutes or less.
@haadullahchoudhry8675
7 ай бұрын
Very thorough. Nice video greatly explained
@ozzstars_cars
7 ай бұрын
Much appreciated!
@jdhn04
3 жыл бұрын
I really appreciate the work you show on this video. Helped me a lot.
@ozzstars_cars
3 жыл бұрын
Thanks Juan, glad it helped out.
@636REDLINE
3 жыл бұрын
Awesome Video Bro. Clear and to the point with exact details on each removal.
@ozzstars_cars
3 жыл бұрын
Thanks for your comment!
@robinsonsauto
2 ай бұрын
Hi sir, are you trying to tell us something by saying we now need to add an additional 1" extension after watching this video.
@ozzstars_cars
2 ай бұрын
It's true Will, who couldn't use an extra inch! 🍆😂
@sixtyfiveford
4 жыл бұрын
Nicely done.
@ozzstars_cars
4 жыл бұрын
Thanks my friend, hope all is well.
@russs3001
6 ай бұрын
nice job explaining and demonstrating
@ozzstars_cars
6 ай бұрын
Thanks Russ!
@traviswilson9198
Ай бұрын
Thank you man you help me out a lot
@ozzstars_cars
Ай бұрын
Glad to hear it!
@paullorenz6457
2 жыл бұрын
Much appreciated! Especially the steps you called out.
@ozzstars_cars
2 жыл бұрын
👍
@markrudis4419
2 жыл бұрын
You're an excellent instructor. Thank you!
@ozzstars_cars
2 жыл бұрын
Thank you Mark!
@joeramirez2333
Жыл бұрын
Thanks your video helped me. I did my job by myself
@ozzstars_cars
Жыл бұрын
Good news!
@mel4stars
Жыл бұрын
This is my first time to do this on my 2005 E350 van. It seems there are different techniques. I've changed 3 and 4 so far working from inside. It seems like it would be easier ,as one guy shows , to release the fuel rail. I am hesitant to do that.
@ozzstars_cars
Жыл бұрын
Why waste time on that? If you do install new orings on the injectors.
@islandguy9380
Жыл бұрын
Excellent video. Just one question, shouldn't you blow out the sparkplug hole with compressed air before you remove the plug?
@ozzstars_cars
Жыл бұрын
That's good practice.
@allenparker13
4 жыл бұрын
Thanks for the great instruction and video on changing these out
@ozzstars_cars
4 жыл бұрын
You're welcome Allen.
@deronaldbaggett3828
9 ай бұрын
Excellent detailed video!! Thanks for all the tips and tricks!!! Great Job!!!
@ozzstars_cars
9 ай бұрын
Thank you for the comment! -Glen
@ozzstars_cars
9 ай бұрын
Glad you enjoyed it! Thanks DeRonald!
@moeb434
3 жыл бұрын
5 and 6 from the front are very do-able. 7 and 8 from the rear, very do-able. 4 from the rear, do-able. 1,2 and 3 I'm not sure. I gave up by then. Lots of crap in the way of these three. Make sure you have a quarter inch swivel joint for your little ratchet. You will need it. Prepare for having your hands scratched and beat up working these tight confined component crowded spaces. If you can do all eight, I applaud you. I only got five. About two hours per plug. This is why I wouldn't trust a mechanic; He might give up like I did and not say anything. But I'll bet he gave up on plugs 1, 2, or 3! I personally feel proud that I went 5 out of 8 rounds! Wish I could have gone the distance, but we are not all Rocky Balboa and love to take a good beating. Happy wrenching my fellow Nutz and Boltzers!
@ozzstars_cars
3 жыл бұрын
1,2 and 3 plugs from the front. Remove 3 coil from the back. I can do all 8 plugs in 1.25 hours easily. Gravy job
@gleneckert1
Жыл бұрын
Thank you....getting ready to attempt this
@ozzstars_cars
Жыл бұрын
Take your time Glen and hopefully things go smooth. One cylinder at a time!
@iandtexarkana4549
2 жыл бұрын
You also need compressed air to blow dirt and debris out before removing plugs. Otherwise, there will be engine problem
@ozzstars_cars
2 жыл бұрын
That's good practice but not necessary on a clean engine.
@suzmaca650
Жыл бұрын
Thank you so much for posting!
@ozzstars_cars
Жыл бұрын
You're welcome Suz!
@lonsomecrow
4 жыл бұрын
Great job man! there are a lot of shitty videos out there. You keep it simple and clear. Thanks!!
@ozzstars_cars
4 жыл бұрын
I try. Thanks for your comment.
@jacobsmithjr
2 жыл бұрын
After watching this it's makes me think my engine may not be that bad off. Repair shop is saying I need an engine replacement but it could be bad coils.
@ozzstars_cars
2 жыл бұрын
Better get a proper diagnosis. Engines aren't cheap.
@jacobsmithjr
2 жыл бұрын
I did but I'm not sure I trust the shop. I have a friend who is a mechanic he's coming by next week. The engine has over 200,000 miles. Wires and plugs were charged a few years ago but not the coils.
@jaydenurch271
4 жыл бұрын
Lots of good info here. My plugs took a bit of force to break free but once I got movement they all came out easily. New plugs in and misfire gone. Cheers mate!
@ozzstars_cars
4 жыл бұрын
Nice work!
@jackreston8188
23 күн бұрын
Thank You. Great video and explanation.
@ozzstars_cars
23 күн бұрын
I appreciate your comment Jack. Thanks! -Glen
@DM-pl8mz
Жыл бұрын
Perfect vid. Helped alot. Thank you 👍
@ozzstars_cars
Жыл бұрын
You're welcome!
@robertbenedict4668
Жыл бұрын
Make it look not too bad .. good vid
@ozzstars_cars
Жыл бұрын
Thanks Robert. After doing it a few times it gets easier but never fun.
@KR0T1U5JUSTINTRESBACK
2 ай бұрын
Cylinder 7 is killing me
@ozzstars_cars
2 ай бұрын
Fun times!
@kenroberts9082
2 ай бұрын
7 and 8 usually has 2B Healeycoiled. Junk!
@kenalexander3046
3 жыл бұрын
Wow! Thank You!!! Very appreciative of this video. Good job!
@ozzstars_cars
3 жыл бұрын
You're very welcome!
@Youngplumbingmafia
3 жыл бұрын
Thanks for making this video. It was a lot of help!
@ozzstars_cars
3 жыл бұрын
You're welcome!
@mobbandit4603
Жыл бұрын
Thank you have e150 and gonna try this
@staceysmith4971
Жыл бұрын
Thank you for this very descriptive video.
@ozzstars_cars
Жыл бұрын
You are welcome Stacy.
@nickingvolboth
26 күн бұрын
Great video broski
@regigilman2255
4 ай бұрын
Hears a crucial tip for ANY sparkplugs R&R GET YOUR PLUG WRENCH BREAK THEM PLUGS LOOSE USE A RUBBER HOSE THAT FITS ONTO THEM PLUG AND THERE YOU HAVE TWIST OFF TWIST ON YOU'RE SO WELCOME😅 ow boys this is gonna grow like there's no yesteryears😊
@tima982
Жыл бұрын
Hi, I have replaced 4 and number 3 cylinder ignition coil &splugs was very difficult to replace so I would really appreciate if you can make a video or something to explain DIY’s like me how to replace without braking anything thank you Temur
@alfredolopez-bruce6199
Жыл бұрын
Hello and thank you for sharing this. Isn't the ignition coil where all the spark plug wires are at? I received first a P0300 and now a P0304 code. I am hoping its the ignition coil that needs to be replaced. If not, then it has to be the wires. Again thank you.
@ozzstars_cars
Жыл бұрын
Coil on plug design does not have spark plug wires.
@alfredolopez-bruce6199
Жыл бұрын
@@ozzstars_cars hello and thanks for replying. So where exactly is the ignition coil at?
@SteveRobReviews
4 жыл бұрын
Tough one to film . Nobody likes to work on Van's especially me :)
@ozzstars_cars
4 жыл бұрын
You do it all Steve!
@SteveRobReviews
4 жыл бұрын
@@ozzstars_cars Yes absolutely, it's called halfass expertise from 40 + years ago. 🤣🤣
@anthonysaponaro6318
2 жыл бұрын
I can not believe I wasted all of that time just to hear a click I didn't even hear, someone had to tell me that I heard it :) Just breakin your balls a lil bit , thanks for the video and taking the time
@ozzstars_cars
2 жыл бұрын
😄👍
@theartofplumbing
11 ай бұрын
Thanks!
@ozzstars_cars
11 ай бұрын
Thank you, I appreciate it!
@FuelTankerMan
3 жыл бұрын
OUTSTANDING~!! Awesome video, very informative, and very well done.
@ozzstars_cars
3 жыл бұрын
Thank you Dan for your comment! I appreciate the feedback. -Glen
@alfonsoyo2722
3 жыл бұрын
Bro u did a lot more than these other videos
@ozzstars_cars
3 жыл бұрын
Yeah I did
@derickpouliot6388
Жыл бұрын
Dude everything I need to know. THANK YOY!!!
@ozzstars_cars
Жыл бұрын
Awesome, glad it helped you Derick!
@RicardoContreras-qs6dc
3 жыл бұрын
Thank you sr your video it was very helpful and very nice to show how it's done..
@ozzstars_cars
3 жыл бұрын
You're welcome Ricardo.
@rpkcustoms
4 жыл бұрын
Thanks for the walkthrough, much appreciated 👊
@ozzstars_cars
4 жыл бұрын
You're welcome and thanks for stopping by.
@glenharper3136
4 жыл бұрын
I did plugs on old Chevy Astro Van for my brother in law once. Had to get some plugs from the bottom and some from the dog house on top. I did one from the bottom and went to the and pulled the next and looked at it and it was brand new. It was the same one I from the bottom. Hands all scraped and cut up. Boy was I pissed.
@ozzstars_cars
4 жыл бұрын
One of those nightmare jobs that make you think what the hell am I doing here! 😂 Thanks for checking out the video Glen. (One N Glen, that's the right way to spell it!) haha Take care.
@michaeltipton536
3 жыл бұрын
You're awesome thank you so much I live in my van I got a 5.4 you're awesome buddy
@ozzstars_cars
3 жыл бұрын
#vanlife passing around the tip jar.👍 Thanks Mike for the comment.
@auxblood
3 жыл бұрын
Thanks for this video, you get a crystal clear angle on a hard to see job. I've got a 2006 E-350 4.8L with 370k of previous neglect, wouldn't be surprised if these have never been changed. I tried to swap the first plug today and applied as much force as seemed reasonable and does not budge. I don't think this is the notorious F-series breakage type engine I've read about but still.. Keep cranking? WD40? Thank you again.
@ozzstars_cars
3 жыл бұрын
The E Ford vans are 2 valve engines and not the dreaded 3 valve but the spark plugs can still strip out the threads or break off. They can be a bear to get out at times. Best to remove them with the engine hot, when you can because the heat helps expand the metal. If the threads do strip out or the plug snaps off you will need to repair the damaged cylinder head. Helicoils don't work well or last and it's best to use something like the Cal Van inserts amzn.to/321VnMH Good luck and hope for the best.
@auxblood
3 жыл бұрын
@@ozzstars_cars thanks a lot
@auxblood
3 жыл бұрын
@@ozzstars_cars warm engine was the trick. smoother idle, power restored, no more codes. Cylinder 6 was misfiring, and the coils' seal was visibly compromised, lots of oily gunk down there.
@ozzstars_cars
3 жыл бұрын
@@auxblood bet your smiling after the repair, one less thing to think about. Good work Dave
@ThemantleofElijah
Жыл бұрын
Hey ozzstar I recently got one of these E-350 it’s a 99 with a 5.4 and has the head gasket oil leak, passenger rear. I’ve read about it how they had multiple vehicles with this issue. I’ve been told to just keep fluids checked and drive it.
@ozzstars_cars
Жыл бұрын
On a '99 it's probably not worth the fix.
@ThemantleofElijah
Жыл бұрын
@@ozzstars_cars I was told by two mechanics it’s expensive and extensive work to do too bad ford didn’t do it right on them. Is there another engine that could bolt up to thst tranny if I ever wanna change it. It’s only got 150k miles on the vehicle
@ozzstars_cars
Жыл бұрын
@@ThemantleofElijah do you have equipment to remove the entire body off the chassis so you can get the engine out? Nehhh
@ThemantleofElijah
Жыл бұрын
@@ozzstars_cars no I sure don’t
@ThemantleofElijah
Жыл бұрын
My mechanic friend told me it’ll prolly go 300k miles just keep oil in it
@filibertovargas8354
3 жыл бұрын
Man thankyou so much for this video.. Nice and clear...
Пікірлер: 368