Your rolling an Iveco MWB. Poor mans Sprinter, another great motor.
@motorsandmetal313
Жыл бұрын
It's not bad for an old motor... It's not going to last many more years though in reality!
@willtricks9432
Жыл бұрын
@@motorsandmetal313 Sold my last one to a breaker for £450 last year. Clutch went at 215K then the gear box a few days later. Earned its keep.
@willtricks9432
Жыл бұрын
I had a 59 Dexta for a few years, I put a Hycrack PTO log splitter on the back, great machine which run the splitter easily. and sounded good but the steering was bad. moved it on to someone to improve and split logs.
@motorsandmetal313
Жыл бұрын
Thanks for sharing 👍 I must admit it is a nicely made piece of kit, steering needs a bit of love in this one also. We are working on the hydraulic system at the moment.. it's a bit stuck up... Mind the oil is gross!
@willtricks9432
Жыл бұрын
@@motorsandmetal313 PTO, three point hitch and Hydraulics are the most useful things I have found in the last 20 years. Shame I didn't find them sooner. Problem I have is stopping myself from buying implements. Will watch the progress. Cheers
@lauriepearce8266
Жыл бұрын
Injector pump needs a new diaphragm , that will stop it hunting
@motorsandmetal313
Жыл бұрын
Thank you 👍 will have a look at sorting that👍
@g.a.f3398
Жыл бұрын
Injection pump definitely needs a new diaphram in it its at the back of the Injection pump undo the 4 slotted screws its in there. They perish and it makes the engine hunt as the rack in the pump is pulled by vacume on the inlet manifold which your throttle lever is connected to change that for a new one and she will be sound then.
@motorsandmetal313
Жыл бұрын
Nice one 👍 I will get one ordered 👌 hydraulics are now fully functional, should be doing an update video on this soon 👍
@g.a.f3398
Жыл бұрын
@@motorsandmetal313 i had a Dexta about 7 years ago i completely rebuilt the engine as a conrod went through the side of the engine block i bought the tractor like it from a local cricket club and so bought a good second hand engine block and put all new internals in it crank pistons rings liners the lot. Then completely shot blasted and painted the whole tractor she looked lovely when she was done see my video on KZitem. Also when you take the cover off the rear of the pump it wont just come off theres a spring in there from what i remember and i think theres a pin that holds the diaphram on the end of the pump rack its a little bit tricky just take your time and the cover will come off there might even be a video on bow to do it on KZitem its not hard just tricky getting the cover off to get to the diaphram.
@jimh3362
Жыл бұрын
Too painful to finish watching. Good luck with the project.
@motorsandmetal313
Жыл бұрын
Cheers Jim. Still figuring out what works best on here 👍
@Daslandroverman
Жыл бұрын
Inviting ideas... Td5 conversion?
@motorsandmetal313
Жыл бұрын
That could be fun.... Anyone got one to donate? 😂
@Daslandroverman
Жыл бұрын
I've a 15P that needs a head gasket?
@motorsandmetal313
Жыл бұрын
@@Daslandroverman tempting... I need to get some other bits and bobs sorted...if you still have it then maybe that's what should happen 🤦👍🤣
@trevorwoods2580
Жыл бұрын
This video is a bit pointless but can't wait till you start working on it
@michaellynskey7124
9 ай бұрын
It’s fairly obvious this man hasn’t a clue about maintaining a agriculture machine after watching this for the first few minutes
@motorsandmetal313
9 ай бұрын
Funny that.... That was the first time moving it or starting it since we brought it and was the first tractor we had owned. We got the hydraulics working and then sold it on to fund other projects. Just interested in what you would have done differently?
Пікірлер: 20