Thank you, one note on the plunger , it is a # 1, not 3 as stated in the vid.
@dantedemonhunter2186
5 ай бұрын
I love the video I'd enjoy seeing you load some 9mm or your other calipers you mentioned thanks for the great video
@ryanashby3640
6 ай бұрын
Thanks for putting the Info out there. I was wondering about more caliber compatibility on the X10 down the road to feed my AKs.
@Mark2A1776
6 ай бұрын
Thank you, just be sure to use a seating die or something to center the case over the priming station
@take1one
5 ай бұрын
Good video. I really need one more station than my dillon 550 has. So instead of a 750 I'd really like one of these x10s. But i have rarely had good luck with Frankford stuff. Should i get one?
@Mark2A1776
5 ай бұрын
I don't have experience with the dillon but my friend does and he really likes my x10
@patworthington3112
4 ай бұрын
Hi Mark, good video. I have had a Dillon 650 for a couple of decades and a 550 for many years before that and love them, but am considering getting an X10 just for my 9mm reloading. I have seen good comments and BAD comments on the X10, so I am a little concerned about spending $1K on the press and then being dissatisfied. Have you had problems with parts breaking? Are you really satisfied with the press? Thanks, Pat
@Mark2A1776
4 ай бұрын
Sounds like you have plenty of reloading experience so you shouldn't have problems. 9mm is great with the bullet feeder FA has great support and I got mine on a Optics Planet 10% off day
@TimLawrence-l3o
Ай бұрын
My question is do you have any lube on your cases Your shell plate moves a lot, I thought it was going to break
@Mark2A1776
Ай бұрын
@@TimLawrence-l3o Yes. I used one shot and it did feel kind of tuff. Now I use one shot the day before and again before I load after it has dried. BIG difference now it runs alot smoother like it should. One shot is kind of funny! If you don't use enough or properly it just doesn't work but when it works its the best. Thank you for commenting
@tommytaylor7851
5 ай бұрын
Hi Mark, what name brand primers are you running in your X-10. I've tried Winchester SPP & SRP but they lockup my X-10.
@Mark2A1776
5 ай бұрын
In the beginning I used Remington magnum on my 44 mag. problems went away when I started using hold or centering dies. I'm using ginex small rifle primers On my 223 and problems are ridiculous they seem to be too tall and or go in crooked over 15% of the time. I had few problems with the ginex small pistol on my 9s n 40s. And few problems wit Federal large rifle on my 762x39. I plan on getting some name brand small rifle and trying again the 223
@Mark2A1776
5 ай бұрын
Also I've noticed locking up accours when the primers don't seat perfect in the primer assembly. That's why I don't use the plastic bumper, having to take it off every time it locks up. I also started using a small piece of hard foam in its place, very low profile to push the base into place but not against the case body. It just sets in place and wears out easy but is effective but not with 223 small rifle primers, they seem to be too tall for the mechanism they look pretty chewed when they run without being set into a case
@tommytaylor7851
5 ай бұрын
Thanks for you replies and time. I've decided my press is a pile of junk and have given up trying to fix my issues. After 6 mos, I'm done. Anyone ask me about FA X-10 press will get an ear full..
Пікірлер: 17