This is perfect! Is what I was trying to do but I didn't know how to make a sketch from the draft workbench and get it into the body.This was very helpful!! I look forward to seeing your next video. You are a true gent!!!! Thank you!
@MangoJellySolutions
3 жыл бұрын
Really glad that this is what your looking for. Freecad gives you so many options through the different workbenches that it's often difficult to figure out what your next step should be in tackling a task. I firm found out about the convert to sketch from trying to import from inkscape files. Since then I have found the feature extremely useful.
@MichelRacic
Жыл бұрын
Menu placements and name have changed but the principle was exactly what I searched for so I learned how to do it in FreeCAD ;-)
@MangoJellySolutions
Жыл бұрын
I need to revisit some of the older tutorials but glad it still worked for you. Thanks for the comment and the heads up.
@ThalassTKynn
3 жыл бұрын
Thank you! I've been trying to figure out how to repeat a pocket along a path for a while now. I never thought to try it from this angle.
@allanpenston7359
3 жыл бұрын
This is a great video, The instructions were clear and easy to follow
@MangoJellySolutions
3 жыл бұрын
Thank you for the comment and the feedback really appreciate it.
2 жыл бұрын
Great video, so many thinks you can do with geometry. I think the menu has changed over time, so I had to find it in the ribbon toolbar. Thanks for demonstrating the principle how to arrange objects on a path.
@MangoJellySolutions
2 жыл бұрын
Thanks for the comment glad you liked the video. At some point I must go back and update the older videos.
@maruwingu9282
3 жыл бұрын
Good very good
@MangoJellySolutions
3 жыл бұрын
Thank you for your support
@muratalptokmakc9633
Жыл бұрын
Thank you
@lewiscobb7817
3 жыл бұрын
Instead of reattaching the sketch to the top face of the body before doing the pad operation- could you just do the pad with a negative distance? Maybe this doesn't allow the through all option. Just learning FC and found your video easy to follow. Keep up the good work and cheers fro m Canada😊
@MangoJellySolutions
3 жыл бұрын
Hi, thanks for the comments glad your enjoying. You could pocket / pad whilst it's still on the bottom. To be honest with you I have never tried a negative value but there is an option called dimension that allows you to perform the operation in both directions. I prefer to lay the sketch on the face that I want to perform the operation through or on as it gets less confusing when you go back to your work to make alterations, and I am easily confused.
@larryvanderschaaf8964
Жыл бұрын
This is great! But I have a need to serate an edge that spirals up, changes radius smaller as it goes, and also twists 90° from start to finish. I thought about using cylinder rods radiating from center.., or patterning a full sign wave... but the twist and non planar surface have me pulling my hair out. Any ideas?
@geraldstubbs2900
2 жыл бұрын
Does FreeCad have lead in/ lead out for making tool paths for plasma cutting? Thanks so much for these videos
@MangoJellySolutions
2 жыл бұрын
Sorry for the late reply, totally missed this one. Not what I know of. I don't have any experience with plasma cutters. Not sure if the paths workbench can help you there.
@geraldstubbs2900
2 жыл бұрын
@@MangoJellySolutions Ok, thanks anyway
@josephmaio
3 жыл бұрын
Very well done video. However, I am wondering if there is a way to make this work with triangles instead of circles (essentially creating notches along a circle). When I try these steps, I can get a series of triangles around the circle, but the triangles themselves turn as they go around the circle, so that sometimes the pointed end points inward, and sometimes outward, and everywhere in between. I am using FreeCAD 0.19.
@wpegley
3 жыл бұрын
Thx, Is there a way too Assembly parts with part array? Im guessing points via array?
Пікірлер: 20