I appreciate these videos. It's hard to find good tutorials these days.
@Adventuresincreation
10 ай бұрын
Thanks!
@jimbessette5353
Ай бұрын
Appreciate your delivery. Nice pace, WELL DONE. I've been contemplating threads for a while and this certainly made it doable. Printing a box right now. THANKS!
Hi there, thanks for sharing these videos! I learned a lot from your channel.
@Adventuresincreation
10 ай бұрын
Excellent, glad to hear it!
@Jose-tw9bl
10 ай бұрын
Great tutorial! Thanks!
@Adventuresincreation
10 ай бұрын
You are welcome!
@cybair9341
10 ай бұрын
I did some bottles before but I did not dare to thread the cap. Now, I can do it. Thanks !
@Adventuresincreation
10 ай бұрын
You are welcome 😊
@markerbaugh4016
15 күн бұрын
Thanks for the video. I see your video uses FreeCAD version 0.21.1, but I'm using 0.21.2 . I don't know if that makes a difference. I followed your example and printed the top and bottom. They printed fine with no obvious print defects, but they don't fit together, the top is too small in diameter. Following your example more closely, when you built the threads on the bottom, you can see that the outer diamter of the threads appears to be slightly smaller than the outer diameter of the rest of the part. When I do it, it looks like the outer diameter of the threads and the rest of the part are the same. This really shows up when you overlay your sketch for the top rotation. The inner diameter (before the threads are cut) of the top is much closer to the inner shoulder of the bottom threads on my version. Also, in your video, after you cut the ScrewDie object, but with threads set to false, the 3d image shows that the ScrewDie object outer diameter is slightly smaller than the rest of the object while on mine, the diameters appear the same. I see there are some setup parameters for the Fasteners workbench. Have you changed yours from the defaults? Also, when I view the data pane for the ScrewTap object from the Fasteners workshop, I have all the parameters set the same as yours, but my data panel shows one additional parameter, Offset Angle, that doesn't show in your video. Thanks
@Adventuresincreation
15 күн бұрын
Hey Mark, can you share your file with me?
@markerbaugh4016
15 күн бұрын
@@Adventuresincreation File emailed
@Adventuresincreation
12 күн бұрын
@@markerbaugh4016 I looked at it, I think it's just the diameter that you need to adjust
@hooperwille
8 ай бұрын
thread offset parameter seems to do nothing, tried even extreme values but nothing is seen visually
@Adventuresincreation
8 ай бұрын
I think you will see the offset is where the thread starts. - I will put something in my next video that shows it more clearly. - Thanks for the heads up!
@rodm4151
10 ай бұрын
Last I checked, the fasteners add on is not available. We're you grandfathered in maybe?
I also successfully made this round box according to your instructions. Then I wanted to use the acquired knowledge for my project and I drow a parametric handle (only the part of the handle that goes into the fist ) for my radio amateur hand cranck generator and I tryed to use the rotate (create a revolve/revolution) function like you use many times I got an error "wire is not closed" But I searched and I can't find where it is broken. (Two points are coincident , Points are collinear ???) Sketch says it is fully constrained. I'm obviously missing some intermediate step. Is there some community to share this?
@CommanderKeen4
9 ай бұрын
i was using three points on the perimeter... then i tried the center and two places and it worked.
@Adventuresincreation
9 ай бұрын
Glad you solved it
@Adventuresincreation
9 ай бұрын
You can share it on reddit r/cadbeginners or r/freecad
@jiritichy6855
9 ай бұрын
Hello. If I want to extract volume(bottle or exhaust/intake manifol of car) I need to plug all the outlets of the solid model, then (theoretically speking) erase one outside surface of the solid, which will make the entire outside of the solid model to fall apart and create only surfacessss and then the inside volume should stay as a solid. I can then use it as a model for the casting core and also test the volume of the bottle....I just cannot find anywhere (user forums or youtube vids.), how to erase a surface from the solid body. Do you have any solution?
@Adventuresincreation
9 ай бұрын
I am not sure you can erase a surface. Depending on the complexity of the surface you may be able to create a boolean operation to subtract the surface
@sveinhovlandsdal2278
10 ай бұрын
Your tutorial is excellent and easy to follow, but this time I'm stuck. When I use "Boolean" the screw is flat against the body, while in your video it is slightly sunken. When I set tread = true the report view shows "Recompute failed!" with a red exclamation point on "Boolean" I have followed your tutorial step by step, the exact same numbers several times and can't see any difference from what you did. I'm on the same version as you. Any ideas on what could result in this error and what to do to fix it?
@Adventuresincreation
10 ай бұрын
It sounds like your thread is not intersecting the part some how
@sveinhovlandsdal2278
10 ай бұрын
@@Adventuresincreation Well, something is obviously wrong, all measurements are identical to yours. Could be something with the settings in Freecad or maybe something in the system settings otherwise... Just have to keep trying! Thanks anyway!
@Adventuresincreation
10 ай бұрын
Can you get your file to me and I will take a look at it for you.
@sveinhovlandsdal2278
10 ай бұрын
@@Adventuresincreation Thanks for the offer, but a complete uninstall and reinstall of FreeCad fixed the problem! Now all that remains is to get the rest of my settings back in place!-)
@Adventuresincreation
10 ай бұрын
Glad that worked, its a bit strange that the re-install fixed it but hey, whatever works! - Thaks for the Ko-fi (beer), I really appreciate it!
Пікірлер: 35