first of all, put a jackstand under the frame so the truck wont sit down on you when the air bags deflate. second- push loc fittings, you must take the air pressure off (pump the brakes till air bled off)., slide a slip joint pliers loosely over the line, push the line towards the fitting, push the collar towards the fitting, then pull the plastic line out. on the rear axel there is a bracket above the spring u bolts. measure 2 1/2" from the spring u bolt saddle to the bracket will get you in the ballpark for ride height.
@ag8499
6 жыл бұрын
Can be leveling valve problem if truck jumps every like 5 seconds on over 60 speed ?
gotta say Vic, i LOVE your "fix it" vids! it's obvious you aren't a pro mechanic, so they demonstrate we mere mortals CAN do the less surgical repairs, even with cheap tools, without a clean shop, etc. though i'd also say when working on air parts, take the 10 minutes to get everything clean before you pull lines. a tiny blob of that grit can jam a valve, and make you buy yet another valve, etc.
@JeffreyPerkins-cg1kl
4 ай бұрын
You guys really really need to stop putting videos on you going to do this changing the part explain the main. Every r&r level of valve video I have watched no one explains where and which line is the supply airline to the valve.
@VideoByPatrick
5 ай бұрын
Nice job...
@ag8499
6 жыл бұрын
It's normal if middle airbags 12.5"inch. then back airbags 14.5"inch? Bobtail. Or how much suppose to be and after I put new one how to adjust it heights?Thanks
@rubberduckyconvoy2723
6 жыл бұрын
Thank you brother. You are help me.
@rickl6697
6 жыл бұрын
I can't believe you didn't clean all that dirt off those hoses before re-installing. Thanks for sharing this video. Be safe.
@Boyleheights213por-vida
4 жыл бұрын
Hey Vic I checked you out Installing the leveling valve Does the leveling valve the main problem why I wake up to NO AIR IN THE BAGS???
@kerrysmith3197
4 жыл бұрын
2 3/8 inch clearance at the axle stop
@ag8499
6 жыл бұрын
Do you know how to adjust highs of this level valve because I have those two bolts what holding valve I can put higher and lower. And I bought it gabriel shucks 50,000 and done 👎no good anymore . Do you know which best one should I put?
@tonyibarra2551
7 жыл бұрын
i have a mack 2013 were can i get info on what the rite level were do you measure to now you are level ?????
@juanaguilar3701
4 жыл бұрын
Socket sizes would have been kool too..
@topdogfreightliner9148
7 жыл бұрын
i just payed $100.00 for this job
@ag8499
6 жыл бұрын
Si how to adjusted airbag height?
@jazzy9086
7 жыл бұрын
nice video
@tytaylor-shorter7302
3 жыл бұрын
Part number for the leveler
@H3PLAYERZ
5 жыл бұрын
Do you have the part number?
@vicmed6088
7 жыл бұрын
that's why you should look at KZitem videos.I hate to hear that.
@Rubioj85
10 ай бұрын
Tku
@flacopa8
5 жыл бұрын
Thanks bro
@udcgtdbjfvnxdhnc.f.g1357
7 жыл бұрын
cool nice to know.
@truckingwithcliff
3 жыл бұрын
I've got to replace mine it's leaking with a load on it. Hell I've change nearly every valve there is on mine.
@rigobertohernandez7333
6 жыл бұрын
Hi Vic I have a freightliner Columbia 2007 how do you know the height ..i seen some videos where they measure like 16 in.
@richardavila7920
6 жыл бұрын
The main thing was too adjusted edits recommended height that's what we want to know
@vicmed6088
7 жыл бұрын
if you have any problems.let me know.i may be able to help
@dannylopez9773
6 жыл бұрын
After installation what height should it be ? Where do you measure from
@littlefellatrucking324
7 жыл бұрын
Great video bro
@vicmed6088
7 жыл бұрын
thanks for tunning in
@ROBERTOPESSANHA
7 жыл бұрын
very good !! thank you....
@vicmed6088
7 жыл бұрын
ROBERTO PESSANHA thanks for tunning in.
@aaronfrancis4178
Жыл бұрын
Good job bud, and he’ll yeah you helped out a bunch.
@saularmenta4504
3 жыл бұрын
Very helpful video,thanhs
@bonbolino14
4 жыл бұрын
Do you need to check and adjust the air ride?
@krossdaboss112
7 жыл бұрын
Was that the reason your ECAS light came on?
@adamgoura1136
2 жыл бұрын
Thank you for your vedios
@diezales6480
3 жыл бұрын
But how we adjust high level?
@3lyen713
6 жыл бұрын
Vic med i have a 1995 fld i need to Up 1 inch on back how i do??? Or i need new leveling valve sistem??
@vicmed6088
6 жыл бұрын
cut the leveling valve rod add some inches to it than weld it together than put it on, good luck
@sr.brobennett2473
6 жыл бұрын
Does the truck have to be running with the brake release in order to make the adjustment to the bag ?
@vicmed6088
6 жыл бұрын
no,everuthing can be off,dont release no breaks,thanks for tunning in
@sr.brobennett2473
6 жыл бұрын
I'm trying to get a axial turbine to buy no any place in CA
@vicmed6088
6 жыл бұрын
no i dont,but thanks for tunning in
@siyadmahammed4296
6 жыл бұрын
Hi I’m thinking replacing my level valve I hear whistle sounds while going some hills I thought turbo sound but my macanic said replace this and see so trying saving labor $150 how do you level? What did you use to measure , please respond ASAP. Waiting u.
@vicmed6088
6 жыл бұрын
i doubt thats its your leveling valve,it sounds like you have a bad air bag,thats why the leveling valve is going off,leveling valve is trying to puch your bags some air,good luck
@vicpetrishak1077
3 жыл бұрын
Spray air springs with Windex or soapy water. Spray valves and fittings. Rust-jacketing occurs between frame rail and top of air spring sometimes leaking there. When replacing air springs , spread weatherproof chalking where frame rail meets air spring ,better than silicone. Pipe dope better on plastic valves than Teflon. Teflon tape is slippery causing over-tightening of fitting breaking valve.
@jadb8452
5 жыл бұрын
Hey Vic, I noticed that my rear bags are more inflated than the front once any idea why or is that the way it spouse to be
@chamba7cities
4 жыл бұрын
I have same problem on my freightliner century n can't no one tell me why
@dimitrovbmw
4 жыл бұрын
this is absolutely normal, thatch how it is supposed to be, nottin to worry about!
@ivansarmiento9574
6 жыл бұрын
My is to long how I fixed??
@vicmed6088
6 жыл бұрын
just buy a new one,
@g41thomas
4 жыл бұрын
How much that valve cost you?
@vicmed6088
4 жыл бұрын
Not much
@davidmedina7108
7 жыл бұрын
you did that.
@sswcubes
3 жыл бұрын
So the nut on the arm behind the valve is what needs to be tightened to maintain the level desired?
@3tree3
2 жыл бұрын
Are you saying I can adjust my ride height on a working valve by loosening that main nut, adjust the bar, then tight it back up? To much air in my bags I feel tooooo stiff
@sswcubes
2 жыл бұрын
@@3tree3 you have to find out what is factory spec level height and adjust it to that height. Or else drive shafts will be out of alignment and cause wear in the differential gears.
@3tree3
2 жыл бұрын
@@sswcubes yea, I'm going to try and check. because all other suspension components from Shocks to motor/trans mounts, cab Shocks/bags is new but still stiff. My test for to much air is it works great when I drop the bags right before a big bump or crack.
@urielsalvidrez9798
7 жыл бұрын
i have a problem with my truck i lose air only when its running when i stop its ok
@vicmed6088
7 жыл бұрын
Uriel Salvidrez choke your wheels than release the breaks.go around the truck and listen to where the leak is.
@urielsalvidrez9798
7 жыл бұрын
an other thing i replaced the level valve but when i weight on it blow too much air it does shut off it that normal i bought after market it from kenworth to go on a freightliner
@tezewright7040
7 жыл бұрын
Uriel Salvidrez. how do you adjust the height.
@culichi55
6 жыл бұрын
I worked for barksdale and fixing these valves were my main job. Made of very cheap material. Allot of returned valves due to failure...Good Video!
@vicmed6088
6 жыл бұрын
wow didnt know that,thanks for letting me know that its cheap material,
@dimitrovbmw
4 жыл бұрын
I ones asked those part sales players when they gona start selling those leveling valves made from all metal! They laugh at me and said never, we have to make money out of yall suckers!
@zqdevilred
4 жыл бұрын
Do you know if leveling valve has grease inside?
@culichi55
4 жыл бұрын
@@zqdevilred yes,each has grease inside.
@zqdevilred
4 жыл бұрын
Thx you for quick answer, I replaced mine and I found some fitings with grease, I was worried.
Пікірлер: 69