As HONDA discontinues parts for our S2000, you're producing more guidelines for us owners to make sure we all take care of our S2000. Thank you for your service, good sire.
@DirtDude117
4 жыл бұрын
And our video Billman strikes again!
@timtubetim
3 жыл бұрын
You are professional mechanic!
@jim6442
4 жыл бұрын
This is great! I need to replace all my lug studs. Might as well do bearings while I'm at it. Looking forward to the bearing video.
@DIYGuysvideo
4 жыл бұрын
Awesome. Its all filmed and will be out soon :)
@Rob.Coleman
4 жыл бұрын
Clear, concise, straight to the point as always. Thanks 👍👍👍.
@rush2redline
3 жыл бұрын
Thank you! Very helpful!
@nathan2234ify
4 жыл бұрын
Nice, straightforward video as always. To remove the lower ball joint only, would you need to follow all these steps and remove the knuckle?
@DIYGuysvideo
4 жыл бұрын
I believe you should be able to remove the lower ball joint without removing the knuckle. Need to remove the castle nut, pop the ball joint, and then remove the two bolts.
@s2k_rob
4 жыл бұрын
Thanks, again :)
@bobbyrios2k223
4 жыл бұрын
Awesome vid. My rear bearing sounds like it might be going out, i hear clicking when i go reverse and forward, already retightened the spindle nut and it went away for a bit and came back 😔
@DIYGuysvideo
4 жыл бұрын
Thanks! Yep. Sounds like the damage is done!
@bobbyrios2k223
4 жыл бұрын
@@DIYGuysvideo that sucks lol
@srqFF
2 жыл бұрын
Since the control arms aren’t messed with, is an alignment necessary after this?
@DIYGuysvideo
2 жыл бұрын
No
@andrewpalma8474
4 жыл бұрын
Do you have a how to video to removing the abs relucter wheels from behind the wheel bearing
@DIYGuysvideo
4 жыл бұрын
Yes, I will doing the whole hub and bearing replacement in a couple videos.
@willisg6878
3 жыл бұрын
Is it the same for the rear ,?
@DIYGuysvideo
3 жыл бұрын
It’s not. Which is why this is a separate video
@jasonwang3413
Жыл бұрын
I had some grease leak out of one of the ball joints when using the separator tool. Does appear to be a torn boot. Think I should be concerned or try to regrease it?
@DIYGuysvideo
Жыл бұрын
It’s not unusual for some grease to leak out when using the ball joint separator tool but if the boot is actually torn how would you degrease it without replacing the boot?
@jasonwang3413
Жыл бұрын
@@DIYGuysvideo Sorry, typo. *Doesn't* appear to be a torn boot. Thanks for the insight!
@DIYGuysvideo
Жыл бұрын
I wouldn’t be too concerned if the boot is intact. There will still be grease in there.
@Apollo_s2k
4 жыл бұрын
I have a clunking noise in the rear every time I go over cracks on the road could this be the noise?
@DIYGuysvideo
4 жыл бұрын
Unlikely related to the wheel bearing/hub. More likely to be related to bushings or ball joints.
@DIYGuysvideo
4 жыл бұрын
Check your tie rod ends specifically.
@Apollo_s2k
4 жыл бұрын
I’ll definitely check those thanks for replying! Also would you consider making a fuel injector installation video? I can’t find a good DIY guide or video that’s useful. People say it’s really easy but I don’t want to mess up your videos are really easy to follow and super helpful!
@DIYGuysvideo
4 жыл бұрын
I have considered doing fuel injectors for a while. I have all the o rings for it but it just hasn’t been a priority
Пікірлер: 28