Thank you thank you THANK YOU!. I just changed my capacitor because I was told by several videos that was my problem due to the humming sound and the furnace not turning on. So I changed it, didn't work and was on my way to order a new motor until I stumbled across your video and did this trick...now my furnace is working again! Thank you!
@Myksgarage
Күн бұрын
Nice to hear!!
@rickysand1900
Жыл бұрын
Even while my induction motor is still working on my 10 year old American Standard furnace, I am replacing it. A heating/refrigerator tech suggested I replace it. Quoted me $1397 plus tax and trip charge. Seeing that amount, I ordered my own online. Same brand too as the original (Fasco). I will be installing it soon. He also suggested I change my temperature sensor. Quoted me a price for the sensor and installation of $201. I ordered one online for $6.97 with free shipping. That piece I did install several days ago. Works great. A 5 minute job. There is a moral to this story. 😂
@Myksgarage
Жыл бұрын
Thanks for sharing
@jazziez6467
Жыл бұрын
i put one on after it was howling so obviously shot after 27 years on my rheem, i bought it on ebay for $250 and 4 bolts to put it on, the repair guy that did a tune up told me it was shot ( i knew it but got the $59 tune up to make sure) and he wanted $800 for it in 2019, furnace still is all original except inducer and hose for pressure switch
@davidbeaudin1106
Жыл бұрын
Yes spun the fan with furnace on off. For 30 seconds. Turned switch on. Went upstairs turned thermostat up. Furnace fired up :) Thankyou 😊
@Myksgarage
Жыл бұрын
Awesome! I'm glad this worked for you !
@GreyEagle3
5 күн бұрын
Unbelievable it actually worked. Out of all the videos I seen I said no way this is gonna work. Thank you ‼️
@Myksgarage
5 күн бұрын
Awesome!!
@joedirt3445
Жыл бұрын
Thank you thank you…Just saved me at least 100 bucks…This was the problem…I oiled the bearings and is running smoothly 👍
@Myksgarage
Жыл бұрын
Nice! I'm glad this worked for you!
@donaldbaker6961
24 күн бұрын
I can not even begin to thank you 😊 you saved the day for me my step dad turned the heat on and nothing I looked and looked I saw the black end of the fan I originally tried to turn it and it didn’t move so I thought it was a cover but after seeing your video I gave it a little harder of a twist it got spinning and back in business thank you so so much 😊
@Myksgarage
24 күн бұрын
Awesome, glad this worked
@mengung2028
7 ай бұрын
I had same problem two year ago. I used W-40 spray front and back wheel and turn back and forth few times and than turn heat on. after running about half to an hour. turn off switch and do it again few times. Now my furnace runs like brand new. At that time, I had ordered new blower thought that blower no good, but I end up that I don't have to replace it.
@Myksgarage
7 ай бұрын
That's a good tip, thanks for sharing!
@lloydmacaya3311
9 ай бұрын
This was a lifesaver, worked after a couple attempts. There was something blocking the fan in my case and could hear loud clinking with either a screw or some piece hitting the fan continuously. It stopped the fan in first attempt. Second attempt i guess it went through after a minute... Many thanks!
@Myksgarage
9 ай бұрын
Glad this worked for you!!
@lloydmacaya3311
9 ай бұрын
@@Myksgaragewhat exactly is this fan called? Just curious
@raylidell3613
6 ай бұрын
@@lloydmacaya3311 its called an inducer motor. If the system does not sense that the unit can vent unburned gasses it will not fire up
@lesliethomas6229
Жыл бұрын
Oh my goodness, time stamp 2:32 just saved me a boatload of money!!!!! You said to turn that fan. Every year you have to turn the fan to get the heat started again. I just tried it and IT WORKED!!!!!! It was in the 40's in my house this morning. So cold I didn't want to get out of bed. As I watched the temperature drop this evening I started to panic. A couple of spins and the furnace started right up. THANK YOU FOR YOUR WISDOM.
@Myksgarage
Жыл бұрын
I'm glad this worked for you!!
@jeffpacetti5800
5 ай бұрын
How can you determine which type of flame sensor or igniter you need? Just search for your unit model I’m guessing? Smart to have spares!
@Myksgarage
5 ай бұрын
Yeah perhaps there is a part number on your existing ones?
@thomas9469
Жыл бұрын
Bro Thanks for doing the video. I had this problem. Thanks from chicago. My fan was inside the grill. I had to use a screw driver to move the fan.
@Myksgarage
Жыл бұрын
Glad it worked for you!
@vires-et-honore
5 күн бұрын
Really interesting. Surprised that some silicone lubricant spray wouldn't help prevent the problem. Thanks.
@Myksgarage
5 күн бұрын
Yeah I'm not sure exactly where I would spray it
@margaretschwartzentruber3154
9 ай бұрын
Good video. I noticed your stored buckets of grain. They shouldn't be stored near the furnace. Too warm. Dependingon the moisture content, you could get some condensation which can lead to mould and mycotoxins. . Relocate to cool and dry.
@Myksgarage
9 ай бұрын
Good tips thanks
@lisax1812
20 күн бұрын
My new HVAC would not start for the first time we turned it on. And may I ask what the on/off switch just above the fan is?
@Myksgarage
20 күн бұрын
I think it turns the power off
@NotKamalasBeach
11 ай бұрын
It's condensation. Between the heat when last used and cool air a little bit of condensation was in your motor and when it sat during the summer it rusted up the motor slightly.
@Myksgarage
11 ай бұрын
That makes sense!
@TruongDuong-ct9fc
8 ай бұрын
Thank you for taking your time to post the video, your trick work
@Myksgarage
8 ай бұрын
Nice to hear!!
@atrangeo
9 ай бұрын
Thanks!!! You may have saved me a tech visit on Christmas! Happy holidays!!
@Myksgarage
9 ай бұрын
Great!!
Жыл бұрын
Hey man it worked🎉🎉! You saved me a LOT of money😅. I appreciate it thank you.
@Myksgarage
Жыл бұрын
Good to hear!
@crand20033
10 ай бұрын
I have never had that problem and my furnaces are 23 years old.
@Samyboy938
10 ай бұрын
@@crand20033ok
@PhoneMartin
6 сағат бұрын
Thanks man. This worked out!
@heatherkohan9869
3 күн бұрын
I'm not sure what is going on with my furnace it comes on but hardly any heat and it makes noises any idea what it could be?
@Myksgarage
3 күн бұрын
I'm not sure what that could be
@zeezee6995
9 ай бұрын
I noticed the plastic rotation know had snapped off. I couldn't place it back on but when i rotated the metal it worked for a while. Can the knob be replaced or glued back on
@Myksgarage
9 ай бұрын
I'm not sure if it can. You can replace the that fan assembly if needed
@ankitabansal2442
12 күн бұрын
ur video helped us. thanks for great help.
@Myksgarage
12 күн бұрын
Awesome!!
@eligebrown8998
9 ай бұрын
I have an old house. I have a furnace that is barely a year old and the temp is 7 dagrees outside but my house won't warm up. I have windows covered, but the house won't warm over 50. My bill is almost 300 bucks this year. Any ideas.
@Myksgarage
9 ай бұрын
does the induction fan turn on at all?
@jeffpacetti5800
5 ай бұрын
I’m wondering if all of your walls are insulated. On an old house, they may not be. You would also want to look at the insulation in your ceiling and under the floor.
@afhevh
6 ай бұрын
100% worked for me, thank you
@Myksgarage
6 ай бұрын
Very nice!
@dominiquebateman-nr5di
3 күн бұрын
Thank you worked perfectly 🙌🏽
@Myksgarage
3 күн бұрын
Thank you
@Thetileguy
9 ай бұрын
Yes it worked for my gas unit
@Myksgarage
9 ай бұрын
Very nice!!
@Saito232005
10 ай бұрын
What does it mean if the black circular piece is spinning, the heater cones on, it just doesn't supply heat out of the furnace. There is also 3 flashes of red light on the circuit board
@Myksgarage
10 ай бұрын
Not sure what that could be.
@Jafiveon
9 ай бұрын
Your manual will tell you what the flashes mean. Or there may be a list of fault codes inside one of the panels. The code will vary by brand. Most common diy issue is your flame sensor is dirty. Remove it and clean it off with a dollar bill or other slightly abrasive substance. Make sure your filter is clean. Dirty filters can cause overheating. If you have pressure switches with tubing make sure the tunes don't have water stuck in them. If you have a glowing ignitor make sure it glows during startup. If it does and then drops out before a click or ignition you may have a bad gas valve and need to call a pro.
@jhatfield2755
8 ай бұрын
Call a technician before u dmg somthing
@blakebozlee4227
Ай бұрын
It worked. Thanks mate
@Myksgarage
Ай бұрын
Nice!
@jazziez6467
Жыл бұрын
just wondering about the fresh air pipe just coming down without a narrowing area off to the side of the inner furnace, also the other exhause seems like it should go thru some smaller black pipes with the water tubes close by, the pipe is blocking the inducer motor and would be hard to replace without taking the pipes off, my inducer is sealed and i don't have anything to spin.
@Myksgarage
Жыл бұрын
Yeah other brands may not be as easy to spin
@jsand3494
11 ай бұрын
Thank you very much for posting .
@Myksgarage
11 ай бұрын
Yes, good luck!!
@MrAbby646
9 күн бұрын
Thank you so much ..
@Myksgarage
9 күн бұрын
I'm glad this helped!
@lindamorgan2678
27 күн бұрын
Ok so your induction fan did not turn on. "furnace not turning on" means alot of things to different people. Mine turns but does not ignite but I will remember this in the future Thank you
@Myksgarage
27 күн бұрын
Yeah there are many things that can go wrong, thanks for watching
@joeperez2348
8 ай бұрын
Thank you thank you thank you!
@Myksgarage
8 ай бұрын
I'm glad this helped!
@B-EAUT-Y
9 ай бұрын
Thanks yous saved our money ❤
@Myksgarage
9 ай бұрын
Glad to hear!
@jibzztube
Жыл бұрын
OMG it worked thanks man you saved my 100$ :D
@Myksgarage
Жыл бұрын
Awesome!!
@stardustgirl2904
7 ай бұрын
Our problem is it sounds like the heater wants to come on , it makes the sound like it's coming on and then it stops. But comes on once in awhile. So we don't know how to fix it!
@Myksgarage
7 ай бұрын
That's frustrating, did you try cleaning the flame sensor?
@stardustgirl2904
7 ай бұрын
@@MyksgarageNot yet, we live in a mountain pass area in California and it's quite cold here. Our unit is in the tiny attic and it's very difficult to get up there but my husband will see if he has time to clean it, between work and city council, and him being the mayor and church , life gets pretty busy around here. Thanks for the video my husband is a do yourself kind of guy and this helps. 🕊️🙏🏻👑
@boost247
2 жыл бұрын
Thank you for your bike unlocking video
@Myksgarage
2 жыл бұрын
👍
@zazeejawad9822
Жыл бұрын
thank you
@Myksgarage
Жыл бұрын
Thank you for watching
@crand20033
10 ай бұрын
Don't touch an ignitor tip with your fingers, it will cause it to fail. Check your capacitor too and make sure it's at the right capacitance.
@Myksgarage
10 ай бұрын
Good tips!
@crand20033
10 ай бұрын
@@Myksgarage My furnace is making a fast ticking noise. Any idea what that could be
@dareevo1
9 ай бұрын
Great!!!
@Myksgarage
9 ай бұрын
👍
@Los-pf3bi
9 ай бұрын
You have humidity problems in your basement. Probably unrelated to the hvac system.
@Myksgarage
9 ай бұрын
Oh??
@Los-pf3bi
9 ай бұрын
@Myksgarage Well, at least I had that problem in my old house. It had to do with poor drainage of the drain pipes to the septic tank. Blower would rust up and cease. It wouldn't be a bad idea to test the humidity.
@luis3557
10 ай бұрын
U saved me 1000 dollars
@Myksgarage
10 ай бұрын
Awesome!!
@choppergunner1408
Жыл бұрын
Not supposed to touch igniters, the oils on your hands and fingers aren’t good for the hsi
@Myksgarage
Жыл бұрын
Thanks for the tip
@Peterbilt-tm1or
Жыл бұрын
Mine only works during the day but not at night when cold
@Myksgarage
Жыл бұрын
That sucks!!
@GETGIBBED
Жыл бұрын
Did you happen to find what was causing your issue?
@MorrisCourtney
11 ай бұрын
Probably thermostat is set to automatically drop the heat temp. You gotta manually set jt
@nicholaslandolina
11 ай бұрын
Moisture in basement is causing the bearings to rot
@Myksgarage
11 ай бұрын
Interesting...thanks for the tip
@MaryHatten-wv3gk
10 ай бұрын
Interesting
@Myksgarage
10 ай бұрын
👍
@yandielgarcia5911
Жыл бұрын
the way you touched the ignitor made me cringe! thats a big no no! thing snaps easy then you are screwed. only clean flame sensor never the ignitor
@Myksgarage
Жыл бұрын
👍
@packleader1215
10 ай бұрын
So, apin my fan and change my filter
@Myksgarage
10 ай бұрын
Okay
@iheartr2280
2 жыл бұрын
Day and night is made by Carrier
@Myksgarage
2 жыл бұрын
Is it any good?
@bluepinky131
9 ай бұрын
WTH... that worked...
@Myksgarage
9 ай бұрын
Nice!!
@davidpetersen7091
7 ай бұрын
Your outside air should come from outside....not your basement!
@Myksgarage
7 ай бұрын
Please explain
@yeahok115sure
Жыл бұрын
Your fan motor is worn out and probably dirty. The
@Myksgarage
Жыл бұрын
For reals?
@yeahok115sure
Жыл бұрын
@@Myksgarage yes, just replace that motor. You can buy just the motor sometimes. They are cheap. Well the ones I’ve replaced where cheap. I think there is 6 screws and a couple connectors and the think pops right out with fan attach to the fan motor. Most likely a set screw is holding the fan to the fan motor.
@noah37374
5 ай бұрын
It’s not working cause you got a garbage cheap brand get what you pay for
@Myksgarage
5 ай бұрын
Oh well
18 күн бұрын
It came with the purchase of his new home Moron, try and pay attention next time.
@georgsondermann9671
Жыл бұрын
This is a gas appliance. Call the HVAC Tech right away. Homeowners aren't trained to work on these appliances. Do one thing wrong and in case of an emergency, the Insurance will not pay up, because it wasn't fixed by certified technician.
@Myksgarage
Жыл бұрын
👍
@swervsplatt9672
9 ай бұрын
Call the HVAC tech? Who every time he comes there's some major issue with the HVAC within a month of him leaving? The people who used to get a private room at a diner I used to work at, whom I overheard talking about how to generate more money for the company by ways of deceptive practices?....
@fatkidwithfudge
10 ай бұрын
Like 80% sure this worked for me. 20% it was turning it off then on again. But gonna say thank you either way!
Пікірлер: 131