Thank you so much man. Your videos are a wealth of knowledge for the Honda community.
@sagittnet2158
Жыл бұрын
Anything to keep our projects going man! Thought l shared some of my experienced and knowledge. But sometimes I still making mistakes but you'll see soon, good lesson though, that's the reason why I want to share. Later man and thank you for watching.
@dylanhoyos4812
2 жыл бұрын
Thank you for this information! I will be building mine for my ek soon
@sagittnet2158
2 жыл бұрын
Your welcome and thanks for watching.
@kevonhiggins6188
6 ай бұрын
If I'm use the f20b head cylinder do I need to cut the f23 water pipe?
@sagittnet2158
6 ай бұрын
Yes, coz f20b cyl head thermostat housing is the same as H22, H23a. Unless you buy the Tracktuff water coolant pipe w/c plug n play, no cutting require.
@williamkennedyii6465
8 ай бұрын
Cost to build me one n shipping to hawaii
@sagittnet2158
8 ай бұрын
lf only l can help you out cousin! Sorry brother
@samhartman7357
26 күн бұрын
If I already have a running f23 in my car can i just use the f23 pistons? Why switch to k20?
@sagittnet2158
25 күн бұрын
The compression ratio is too low and it'll be too slow to accelerate at low rpm. When k20 piston is use it'll bump your comp ratio to 11:1
@sagittnet2158
25 күн бұрын
That's when using a H22 cylinder head on F23 block.
@skylineimg7246
Жыл бұрын
Hey Sagitt. Where can i find an Oem F23 head gasket. Cant seem to find an Oem gasket.
@sagittnet2158
Жыл бұрын
Hondapartsonline.com, there are 2 F23 headgasket they sell (12251-paa-a01 and a02) either one can be use but always check the copper rivets, if it's will be sandwhich by 2 surfaces, simply remove it. The 2 dowell pins on the block will guide it center. You can also check Amazon, someone is selling it. If you cant buy it online, there's always stealership ( more $$ of course) but less headache in the long run. You dont have to worry about oil leaks. Not sure what type of plugs did you use on cyl head, in case you use kstuned plugs. I recommend to smear some sealant on top and bottom part for added assurance. Seen others complain about oil leaks still. I use sealant called Mega grey, it's same stuff as Hondabond.
@skylineimg7246
Жыл бұрын
@@sagittnet2158 thank you. Found it! I will be using the ks tuned plugs.
@marcsteffen3983
10 ай бұрын
Where u finding oem honda f23 headgaskets??
@sagittnet2158
10 ай бұрын
I usually order it on online Hondapartsonline.com or Honda dealership.
@marcsteffen3983
10 ай бұрын
@sagittnet2158 cool. I appreciate it man
@nicholassantos2327
2 жыл бұрын
Thanks for the knowledge man!
@sagittnet2158
2 жыл бұрын
Anytime brother, any little thing can help.
@Grocery_Wagon_Racing
Жыл бұрын
Could you do this build with a bored f22a block? Have a couple of those laying around and want to build something NA.
@sagittnet2158
Жыл бұрын
Yes and it'll be g22. The engine will be similar to a H23a (bluetop) they have same 95mm crank except your f22 is 50mm main bearings. I'm not very familiar on g22 build as far as w/c piston to use but for timing belt areas, use H22.
@Grocery_Wagon_Racing
Жыл бұрын
@@sagittnet2158 thank you for the quick and detailed reply! I'll do more research on the G22 now. Love your videos been watching a bunch after stumbling across your channel today. As far as I know I can use the k20a2 pistons in reverse like you did but need to use aftermarket f22/h23 rods for the wrist pins.
@sagittnet2158
Жыл бұрын
@@Grocery_Wagon_Racing Thank you and yes, k20a2 can be use on those rods.
@brandonmartin147
5 ай бұрын
Which pistons for turbo
@sagittnet2158
5 ай бұрын
K20a2 Cp piston or Arias, that way you dont have to deal w/ wrist pin offset. Cp and Arias doesnt have wrist pin offset. Visit www.zealautowerks.com to figure out your comp ratio.
@brandonmartin147
5 ай бұрын
@sagittnet2158 thanks man love videos
@nolanadam1093
Жыл бұрын
Have u tried cometic multi layer head gaskets they come in different thicknesses
@sagittnet2158
Жыл бұрын
Never tried Cometic, I used Felpro one time and we found out it was the caused of oil leak and never used any other brand after that other than Honda headgasket. Not sure w/c cost more than Oe or Cometic. If it's about same price maybe 1 day l'll give Cometic a try.
@lucygelz
Жыл бұрын
Do you have an Instruction on plugging the oil galleys for the block
@sagittnet2158
Жыл бұрын
Kstuned have a instructional video for different block. I did it on one of my f23 block before using their instruction. Maybe one of these day l might do a blog about it, showing my diy plug.
@lucygelz
Жыл бұрын
@@sagittnet2158 please update me if you do
@sagittnet2158
Жыл бұрын
@@lucygelz no worries man! I'll be making a blog about it soon. It'll be on the cyl head and l'm going to use a expandable rubber also, just like what l did on the oil pump.
@sagittnet2158
Жыл бұрын
@@lucygelzPlugging the h22 cylinder head is uploaded! You'll see it on regular day time show. Thanks man!
@BlackAx33
4 ай бұрын
awesome video!! question, you said this was a NA build, would I need to change parts for a turbo setup?
@sagittnet2158
4 ай бұрын
NA setup and yes, it's best to install a turbo piston w/ forged rod if going boost.
@BlackAx33
3 ай бұрын
@@sagittnet2158 damn thanks for the advice my man! I'm thinking of seriously doing this build and your videos are invaluable!
@sagittnet2158
3 ай бұрын
@@BlackAx33 thanks brother!
@peterbryant3584
Жыл бұрын
This was a great video thanks
@sagittnet2158
Жыл бұрын
Thanks bruh!
@stevenjames3356
Жыл бұрын
For the oil drain plugs could i weld before i get the head resurfaced
@sagittnet2158
Жыл бұрын
Yes, weld it shut then send it to get resurface. If your plan is welding it, might as well add a material on the #2 oil drain. Its on the intake side. That way you can use a aftermarket headgasket if you wish. I found out that using other than OE headgasket, it leak oil on that side. You can watch one of my vlog about it. I showed where it was that aftermarket gasket not covering oil drain much.
@stevenjames3356
Жыл бұрын
@@sagittnet2158 thanks man 🙌♥️i love your videos,I'll go watch that video as well 🙂
@@stevenjames3356 it's right at the beginning/ headgasket.
@michaelmontalvo1999
2 жыл бұрын
What did you use for engine harness and ecu (obd1 or bod2)?
@sagittnet2158
2 жыл бұрын
I used a 1996 Civic lx harness(obd2a) and extended some wires and change some connector for IAT.
@jasonphilips4731
Жыл бұрын
@@sagittnet2158 I am also considering using my stock harness for my Eg.
@sagittnet2158
Жыл бұрын
@@jasonphilips4731 it'll work, just need to extend or add some wirings. I found that obd2 connectors are much easier to depin compare to obd1.
@jasonphilips4731
Жыл бұрын
@@sagittnet2158 Ok thanks 👍
@derekcooper1796
Жыл бұрын
Love your videos!
@sagittnet2158
Жыл бұрын
Thank you!
@Merk_wallberg
2 жыл бұрын
So do I need to modify reliefs on my nippon k20a2 pistons for my g23 or can I just drop in?
@sagittnet2158
2 жыл бұрын
Drop in, l just shaved the relief back then just for a R&D. There are plenty of p2v clearance .
@Merk_wallberg
2 жыл бұрын
@@sagittnet2158 thank you so much, love the videos
@sagittnet2158
2 жыл бұрын
@@Merk_wallberg thank you brother
@Merk_wallberg
2 жыл бұрын
@@sagittnet2158 sorry one more question, even with a big cam like a skunk pro 1 you don’t think k20 piston exhaust relief needs to be opened up a little?
@sagittnet2158
2 жыл бұрын
@@Merk_wallberg lf you use a CP piston no need, there's plenty of room. If Oem piston is use and require to be install backward coz of the offset then l think it wont hurt to widen the exhaust relief. But it's better to clay it so to be sure. What piston are you thinking of using on f23 block? Nippon racing jdm piston or Cp piston?
@negativeex7067
Жыл бұрын
What pistons should we use for low compression?
@sagittnet2158
Жыл бұрын
Variety of piston brand off the shelf to use actually. I'm using k20a2 Cp piston coz it does'nt have a wrist pin offset. No need to install piston backwards to orient the piston pin offset like regular F23 piston. Are you thinking of boosting the g23? Pick a k20a2 piston that is advertise to have a of 9.1 to 9.6. 1 ratio for example and visit www.zealautowerks.com, type all information together w/ k20 piston dome CC value. From there that'll give you an idea.
Пікірлер: 74