When I say I done & experienced everything you did I done it(replacing parts)... I had a hard time believing it was damage. THANKS-A-MILLION dude.😘👍🏽🥰
@BigSyTech
2 жыл бұрын
That was an emotional rollercoaster. Thank you for the informative video and a few laughs. You had my parents cracking up.
@bluedevilg3542
2 жыл бұрын
Lol it was crazy but still running strong. I’ll post another update video tomorrow thanks for watching 🤙🏽
@tpalmen
2 жыл бұрын
I did this on a 2006 Rav4 and worked great! I did a complete radiator flush first, left the thermostat in and poured it into the overflow tank. My overflow drains directly down into the rad so I figured it was safe. Rad + block holds 7.2 liters so I added 5 liters then the gasket sealer then topped off while running. Runs better than it has in years, even leveled off my fuel trim numbers.
@bluedevilg3542
2 жыл бұрын
That’s bad ass mine is still running strong 💪🏾
@antoinedantley3679
2 жыл бұрын
@@bluedevilg3542 do you drive fast? Ima bit of a spirited driver, wondering if this’ll hold up in my car
@bluedevilg3542
2 жыл бұрын
@@antoinedantley3679 yes I get up to speeds at times all tho I do obey the speed laws wink wink but it’s held up pretty good 👍🏽
@user-kk2dk6gn8d
Ай бұрын
You had me laughing my ass off. Loved your story. Hope it lasts a good long time for you.
@topgun52
Ай бұрын
The instructions say to turn the heater on max while pouring in the solution, I didn't hear you mentioned you did that which may have contributed to the scare you had. Glad to hear that it worked and I know you were very relieved. I know that feeling been there done that! Thanks for sharing
@glenndelrosario
2 жыл бұрын
I like how you cus... great storyteller!
@bluedevilg3542
2 жыл бұрын
I’ll watch my mouth next time 😁
@lmathews4666
Жыл бұрын
My turn , I'm going to give this video to my mechanic, I always give him the best advice 🤭🎀thanks !
@bluedevilg3542
Жыл бұрын
Hell yea
@allenwebster6329
Жыл бұрын
I think the way it works is once it reaches the leak the heat from the cylinder heats the sealer up and it gets hard almost like glass ,I've heard it works but I'm not sure if it lasts along time but even it works for a few months that will give you time to do what you need to do to fix it right hey yeah if it works that's a good thing
@nedoscarsandfishingvideos5500
2 жыл бұрын
Good video going to try it
@bluedevilg3542
2 жыл бұрын
Good luck
@phoenixwest602
2 жыл бұрын
I did this on my first G white smoke was coming out of the exhaust ..it works .
@bluedevilg3542
2 жыл бұрын
Hell yea it does mines still running good
@silent_torseeker7741
2 жыл бұрын
My g started smoke exhaust 2 days ago but lightly and some times after a big slow down
@Joshy10k
2 жыл бұрын
@@silent_torseeker7741 did you try it? Did it work?
@allenwebster6329
Жыл бұрын
I used I seal on my 2001 explorer sport trac it seemed to work I dont think my leak was very bad but in time I'll most likely put another engine in it from another trk I have ,but hey if it works for awhile that's a good thing right
@DTUFINOPhotography
2 жыл бұрын
Same problem on my fx35.... i replaced thermostat, fans, hoses and today i replaced my radiator. the coolant just ends up overflowing in my reservoir. but my engine is not overheating, which is weird. But it did overheat yesterday after a good 100 mile drive.
@bluedevilg3542
2 жыл бұрын
Get a compression test brother to make sure you don’t have a small leak in the head gasket
@MarcoGonzalez-bi6cg
Жыл бұрын
Same here it’s a head gasket a small leak I overheated my engine 2 years ago and it’s still runs good it only pushes to reservoir when I drive up to 100 mph at freeway and when I gun it and do hard pulls back to back
@DTUFINOPhotography
Жыл бұрын
@@MarcoGonzalez-bi6cg What you do to fix?
@Mik35959
2 ай бұрын
You can press the thermostat out of the housing using pliers its a spring fit. Especially since you had just replaced it you could have used the old one
@vatoloco5639
2 жыл бұрын
I took off my thermostat inside spring off with some heavy-duty channel lock plyers,and put on back on with a new gasket back on then is just straight now.
@bluedevilg3542
2 жыл бұрын
Nice wish mine was that easy
@1wpk911
3 жыл бұрын
Damn dude, car has to be cold we got it
@bluedevilg3542
3 жыл бұрын
For sure bro won’t work when it’s hot. Glad it worked out for you 🤙🏽
@jimgoodreau1245
Ай бұрын
I have a 2008 g35, and was told i had a blown head gasket! Didn't take the thermostat out, but poured a big bottle of blue diamond , poured in the hole bottle slowly. Radiator started to boil , put cap back, after about 20 minutes got hot! Turn it off and went to bed! Surprisingly has not over heated in 2 months!
@billcampos3300
Жыл бұрын
I had similar situation in a different car. The temperature gauges were messed up so it was giving me false reading. There was no overheating. It was just that the gauges were messed up. There was smoke towards the back that was mentioned in that area. That is where the temperature gauge is at for the coolant I’m not saying that the issue was just seems kind of coincidence
@gerodriguez1993
2 жыл бұрын
These cars are hard to bleed out did you use a coolant funnel and did u rise up the car and bleed it? Also, from the bleeder valve?
@bluedevilg3542
2 жыл бұрын
Yes I did. Also had a compression test and that’s how I found out I had a leak in the head gasket
@bluedevilg3542
3 жыл бұрын
Forgot to mention before you pour it in have the heater on full blast which it mentions you on the instructions anyways just thought I’d throw that in
@jamesmay5394
3 жыл бұрын
To take the t stat off you cut out the spring and basically gut out the housing and pop it back on. Just figure incase you want to try it drops the temps alot. I run the fans on high also jump the relay for fans.
@bluedevilg3542
3 жыл бұрын
@@jamesmay5394 cool thanks but so far still running strong 💪🏾
@MrSwaggahot
2 жыл бұрын
i got a 2008 fx35 i took the thermostat out the housing , youll need a needle nose pliers to twist the thermostat out of the holders
@bluedevilg3542
2 жыл бұрын
Might try that next time 👍🏽
@geo-fy1my
3 жыл бұрын
the thermostat can be taken off the housing. you just need a flathead to push it off the things that hold the thermostat to the housing.
@bluedevilg3542
3 жыл бұрын
I tried for like an hour that shit wasn’t budging at all one bit. The rout I went ended up working either way still going like a champ 👍🏽
@geo-fy1my
3 жыл бұрын
@@bluedevilg3542 damn it was probably stuck or something because when i took it off the whole thermostat came off the housing and i just put the housing back on because i was having bleeding problems. turns out it’s my head gasket that’s fucked because it only overheats 15 minutes into a drive. thanks for the reply tho bro
@geo-fy1my
3 жыл бұрын
@@bluedevilg3542 ima go to autozone and buy the blue devil and see if that temporarily fixes it
@bluedevilg3542
3 жыл бұрын
@@geo-fy1my mine was doing the same shit. Good luck. Just make sure you follow the instructions carefully. Let me know how it goes
@geo-fy1my
3 жыл бұрын
@@bluedevilg3542 yeah i’ll let you know when i put the blue devil in and see if it don’t overheat no more
@ROMEOHEALINGHANDS
2 жыл бұрын
I did it on mine but i spray it with a water hose to the motor to prevent over heating for an hour an it got fix
@bluedevilg3542
2 жыл бұрын
Nice bro 🤙🏽
@SaskFisher
3 жыл бұрын
I've heard about this stuff. Wondered how it actually works. Nice video
@bluedevilg3542
3 жыл бұрын
Works great I approve
@alejandrotobienne584
2 жыл бұрын
It’s like liquid glass so once it touches the combustion leak on gasket the chemical in the coolant liquid evaporates and the chemical hardens. Works with water or coolant. Best to run heater during initial use. After leak test is done and passed you can remover heat.
@alejandrotobienne584
2 жыл бұрын
Hopefully your saving towards new gaskets on the VQ. Yes the mechanic will give you shit about using this. But with multi layer gaskets. VQ’s will do 400k.
@bluedevilg3542
2 жыл бұрын
Yea eventually I will replace them down the road but as for now she working good
@alejandrotobienne584
2 жыл бұрын
@@bluedevilg3542 just don’t depend on this to much and forget. Gaskets are only 65 for set or just save towards another motor and Core your old motor for like 500 dollar discount. Tons of folks here in FL sell VQ’s. Don’t wanna leave you stranded
@gilgarcia50
5 ай бұрын
Did you have to bleed the system after?
@CoreyB1980
Жыл бұрын
You might need to burp the system to stop the needle from moving now and then..
@teddharvey1493
2 жыл бұрын
My 07 M35 is doing the same thing yours did except NO engine shake And noises. The smoke is coming from the same area once the engine gets warm..
@bluedevilg3542
2 жыл бұрын
Is it still over heating?
@notyouraveragericer
2 жыл бұрын
Compress the spring on the thermostat and it will come off
@bibybilbao1386
2 жыл бұрын
when you said the needle goes up a little bit still, when does it do that? when ur driving or?
@bluedevilg3542
2 жыл бұрын
It would only do it at the red light but not as much anymore car still running good
@MultiHondaa
2 жыл бұрын
Bruh 😂 We The G Owners.
@bluedevilg3542
2 жыл бұрын
Hell yea lol
@ninetyseven7656
2 жыл бұрын
Thanks
@seans158
Жыл бұрын
Did you see coolant leaking back behind the engine before you put this in? Mine is loosing coolant and smoking in the same area, looks like from the block, but its not overheating.
@sergeesy8654
Жыл бұрын
maybe your missing a gasket for the bleeder valve , or just the bleeder valve itself is messed up
@bluedevilg3542
Жыл бұрын
No I didn’t I did a compression test on it that’s how I found out it had a small leak
@andybailey3703
2 жыл бұрын
You can use the other to with out taking thermostats out
@bluedevilg3542
2 жыл бұрын
Yea it’s the one I ended up using
@goodguycooper
2 жыл бұрын
dude your story telling is fucking hilarious but i’m having the same issue and a g35. hoping i don’t have to use this blue devil stuff but we’ll see…
@bluedevilg3542
2 жыл бұрын
🤙🏽
@gretabridges3364
2 жыл бұрын
I waited 2weeks, 356+miles, & a 6hour+ road trip b4 I posted. YEZZZZZZZ this shit WORK!!! I went by his (EXACT) direction My HAPPY2000 4cyl Honda Accord EX
@bluedevilg3542
2 жыл бұрын
Hell yea bro my shit running strong too after a 12hr trip
@picklerix6162
Жыл бұрын
There’s a bleeder valve back towards the firewall. I have a 350z (which is almost identical to the G35) and it will definitely overheat if you don’t bleed the air out of the cooling system.
@bluedevilg3542
Жыл бұрын
Yea that’s one of the first things I tried but ultimately I did a compression test and I had a small leak in the head gasket
@miguelharo9080
2 жыл бұрын
How can you tell if the radiator is half full or empty ? So you don’t mess up ?
@bluedevilg3542
2 жыл бұрын
Honestly man I fill it up then I kinda eye ball it and stop it when I think it’s half way. It doesn’t have to be Precise as long as you empty a good amount and leave some in should be good enough.
@zleepwo8520
2 жыл бұрын
Time for a new cooling system …that clogs the radiators coolin fins and everything else …it does fix the leaks temporarily but in the long run …it’s a no go
@bluedevilg3542
2 жыл бұрын
Maybe but for now imma run her till the wheels fall off 😁
@Joshy10k
2 жыл бұрын
@@bluedevilg3542 how long did it last till you had to either do it again or fix?
@bluedevilg3542
2 жыл бұрын
@@Joshy10k 1yr but I took it on a 8hr round trip non stop on a hot ass day lol I think it would’ve lasted longer but yea 1 yr. Still not bad tho. I re did it and been a few months now still going strong 💪🏾
@teddharvey1493
2 жыл бұрын
Should I flush it out before using this or do it as you explain?
@bluedevilg3542
2 жыл бұрын
Sorry for the late response I wouldn’t hurt to flush it that’s what I did the first time. But if you don’t want to mess with all that you don’t really have to
@Sroor2023
6 ай бұрын
I want to try it, but I am scared and prefer to do it myself, replacing headgasket the hard way
@bluedevilg3542
6 ай бұрын
Try it
@TheIsaacDelcid
2 жыл бұрын
My g35 immediately overheats when i turn on the engine.. is it okay for me to use this sealer still? Because you said to run it cold but my car overheats as soon as it turns on..? Any suggestions?? 🙏🏼
@bluedevilg3542
2 жыл бұрын
First have you checked all the other things that it could possibly be like thermostat air bubbles in the system clogged radiator ?Or have you done a compression test to make sure it’s your heads ?
@jorgem.4382
Жыл бұрын
@@bluedevilg3542 for me its my heads, what should I do?
@bluedevilg3542
Жыл бұрын
@@jorgem.4382 try the blue devil if you don’t have the money to fix it
@jorgem.4382
Жыл бұрын
@@bluedevilg3542 okay bet cuz i def dont, will it be at an autozone
@bluedevilg3542
Жыл бұрын
@@jorgem.4382 yes
@bobbybranum4102
2 жыл бұрын
Did u have to bleed the air out after putting this in ?
@bluedevilg3542
2 жыл бұрын
Yes
@alejandrotobienne584
2 жыл бұрын
Do you have a oil leak from gasket too.
@bluedevilg3542
2 жыл бұрын
Nope
@CleranceElva
2 жыл бұрын
Did the engine make a knocking noise when your head gasket went bad?
@bluedevilg3542
2 жыл бұрын
No. Is yours making that right now
@CleranceElva
2 жыл бұрын
@@bluedevilg3542 yeah. I accidentally overheated the engine and now it knocks
@bluedevilg3542
2 жыл бұрын
@@CleranceElva does it still over heat ?
@_1noclue
2 жыл бұрын
I replaced everything then folks told me my head gasket bussed and my bleed valve tube had to be replaced
@bluedevilg3542
2 жыл бұрын
Hmm weird if your head busted there’s no need to replace the bleed valve
@BrandonKnight-il9xs
3 ай бұрын
Those engine covers hold heat around the intake, I'd can it immediately
@chingli-xg4ns
5 ай бұрын
GUYS which is BEST to WORST liquid products? ¹). Blue devil. ²). K-Seal. ³). Bars. or ⁴). CRC.?.
@slayergg3447
Жыл бұрын
Yoo mine stays at a normal temperature but after a while the temperature starts going up and i took the thermostat off and leave like that but still overheat after a while it keeps the normal temperature por a while but then it starts going up again
@bluedevilg3542
Жыл бұрын
Make sure you get a compression test first before you start changing parts and wasting money.
@MultiHondaa
2 жыл бұрын
Look out for trolls.
@brianwilliams1114
3 жыл бұрын
The thermostat can’t be taken off?
@bluedevilg3542
3 жыл бұрын
You can’t separate the housing from the thermostat it’s super hard they sell them separately but it’s like a special order but the pour n go blue devil works just as good
@yonicsanchez226
11 ай бұрын
It’s a temporary fix my car engine ran almost 6 ,000 miles and started over heating again got rid of the car now
@mrlude490
9 ай бұрын
*Bump for Updates*
@jorgeavila4158
2 жыл бұрын
what are the symptoms of a damaged cylinder head i have a 2008 infiniti g37 coupé and i noticed something in the oil cap like white cream with coffee and .?😐but the car feels good
@bluedevilg3542
2 жыл бұрын
As long as there’s no cream coffee stuff inside your oil your good 👍🏽
@nighthawk0077
2 жыл бұрын
what about the dipstick?
@progressnotperfection81
2 ай бұрын
Did you take the thermostat out first?
@bluedevilg3542
2 ай бұрын
At first I did but you don’t really need to
@progressnotperfection81
2 ай бұрын
Ok, ima try the temp sensor first
@simplemanrv8229
2 жыл бұрын
So is the engine supposed to be cold or do you need to run it for 20 minutes before you add Blue Devil like you said?
@bluedevilg3542
2 жыл бұрын
Cold
@alibeize3251
Жыл бұрын
Was the oil milky?
@bluedevilg3542
Жыл бұрын
Nope
@wolfeadventures
Жыл бұрын
So you never trained the blue devil it’s still in the radiator?
@hanialjabri6952
3 ай бұрын
Why don't reples the head gasket
@austinbradley3411
Жыл бұрын
Anybody ever used the rear main seal stop leak?
@bluedevilg3542
Жыл бұрын
Never had but I’ve heard good and bad
@austinbradley3411
Жыл бұрын
What's the bad?
@jorgeramirezsatx2073
2 жыл бұрын
My oil super milky and smoke true tail pipe
@bluedevilg3542
2 жыл бұрын
Blue devil will probably fix that
@korysmith5871
Жыл бұрын
@@bluedevilg3542 do I need to change the oil first before I pour this in cuz my oil is milky
@bluedevilg3542
Жыл бұрын
@@korysmith5871 yes I definitely would
@giovannicorral4795
3 жыл бұрын
Did u take the thromasta off
@bluedevilg3542
3 жыл бұрын
No sir but make sure if you’re going to use this on your car get the pour n go. Do you have a g35 ?
@giovannicorral4795
3 жыл бұрын
@@bluedevilg3542 yes 2004 just started over heating n leaking coolant
@giovannicorral4795
3 жыл бұрын
@@bluedevilg3542 coupe to
@bluedevilg3542
3 жыл бұрын
@@giovannicorral4795 do you know for sure if it’s your head gasket?
@giovannicorral4795
3 жыл бұрын
@@bluedevilg3542 yeah u let all the coolant out or no
@yonicsanchez226
Жыл бұрын
Is it still holding ?
@jayz_moto
Жыл бұрын
Wondering aswell 😂
@yonicsanchez226
Жыл бұрын
@@jayz_moto I did mine already ran the car for 1000 miles so far so good
@jonnyboat2
Жыл бұрын
Starting at around 8:05 you begin explaining your using the blue devil by saying that you turned the car on and ran it 20 minutes before adding the blue devil. That isn't in the directions.
@bluedevilg3542
Жыл бұрын
Yea I know I am not perfect but doesn’t really hurt anything
@patrickbarnes9768
6 ай бұрын
im living in jamaica I can't recall seeming this product
@HubbyKingg
6 ай бұрын
You didn’t do it right. Suppose to flush first
@bluedevilg3542
6 ай бұрын
I got it the second try 😉
@miguelharo9080
2 жыл бұрын
My g35 has been overheating I replaced the thermostat not sure what it could be smh
@bluedevilg3542
2 жыл бұрын
Try going thru the easy test first. like one see if you have a air bubble try bleeding it sometimes you’ll get the air bubble out. Two check your radiator fans make sure they’re working. Three make sure your radiator is good like check for cracks leaks on it. Four make sure your water pump is good. And last I would get a compression test on it that would tell you if you have a leak in your head gasket. That was my problem after I went through all that I ended up having a leak in the head gasket.
@steveherrington2151
2 жыл бұрын
Well you obviously did not read the instructions,because you were supposed to use an engine flush,and flush out the enigine BEFORE you pour this in. Before you make a video of a product, FOLLOW the instructions And lose the all the cussing. Bad video.
@bluedevilg3542
2 жыл бұрын
I can read English you know and I did flush the engine out before otherwise it wouldn’t of worked that’s like one of the first instructions on the bottle I guess I forgot to mention it my bad
@kcsweesy
2 жыл бұрын
Not a bad video if you'd leave out foul language
@bluedevilg3542
2 жыл бұрын
@@kcsweesy I’ll work on it boss
@priusgame1178
2 жыл бұрын
The product always works for people selling the car or after a day, lol. Real car people know this is all garbage stuff that plugs up everything in coolant system. Pumps, radiator, lines, heater core all get plugged up with plastic debris from this product solidified in the coolant system. It's a garbage product that leaves the next guy having to replace the engine along with pumps and coolant system. Do not buy this product unless you buy all of your repairs and parts from garbage auto zone. This guy in the video cusses too much and clearly doesn't know about cars.
@bluedevilg3542
2 жыл бұрын
This dude first off all I don’t sell cars this car is staying with me for a while. Second it’s been over three months still running strong driven it for over 3k miles 12 hour round trip in 100 degree weather. Third I do buy some of my shit from auto zone I ain’t rich. And final I never said I was a professional with cars my dude 😁
@priusgame1178
2 жыл бұрын
@@bluedevilg3542 you'll be selling it soon for random low coolant and random overheating issues. Then come back and update everyone it doesn't work. That's all I repair is idiots using that garbage
@bluedevilg3542
2 жыл бұрын
@@priusgame1178 and I bet you’re one of those mechanics that rips people off charging a lot for something that’s a easy fix. Plus like I mentioned in my video I am still going to replace the engine at some point you idiot. 😁
@priusgame1178
2 жыл бұрын
@@bluedevilg3542 Actually, I buy a lot of cars to rent out. I'm always buying non runners so if anything I volunteer to take on the head gasket jobs and engine swaps. Most of the time when I see crystallization around hoses and radiator caps I always know because some clown wanted to autozone fix this issue now I gotta change out pumps, radiators, hoses. The best part is when these morons record it and go on KZitem flexing they know more than car people saying they fixed it with a bottle of that crap. Open your radiator or look at the water pumps maybe you'll see you were wrong this whole time.
@priusgame1178
2 жыл бұрын
Point being you actually make things a lot worse when you use this stuff. When you do the engine swap or whatever you do you'll see there's actually more stuff you need to swap out like pumps and radiator and hoses and flush heater core. Also, ease up on the cussing too, man.
@waltercardenas7354
3 жыл бұрын
This product will damage your engine.
@bluedevilg3542
3 жыл бұрын
Best engine bandage for your buck if you can’t afford 1500 to 2500 on a new engine I say this is a good product my car been running like a champ so far 👍🏽
@josepharana6786
3 жыл бұрын
No it will not.worked perfectly for me.2005 Uplander.
@bluedevilg3542
3 жыл бұрын
@@josepharana6786 👍🏽
@josepharana6786
2 жыл бұрын
@@bluedevilg3542 still working 1500 miles later
@josepharana6786
2 жыл бұрын
Heat works and everything
@mastertech6049
2 жыл бұрын
bro get to the fucking point
@bluedevilg3542
2 жыл бұрын
Yea I know I do need to get to the fucking point when I make these vids I’ll work on it
Пікірлер: 204