Thank you SO much for this KZitem tutorial! I am a 72 year old, non mechanically- minded woman who just repaired her dishwasher.
@Lisa-ox3vq
2 жыл бұрын
Nancy, I'm a 71 year old woman that's about to do the same!!!
@RyanDavis87
2 жыл бұрын
Just for clarification 815 is not the error code it is the UI software version (ie: Version 8.15). If the door is "detected' as being open all of the LEDs will flash while in "Consumer Error Mode" (hold "start" and "select cycle" buttons for 5 seconds) If the door is detected as closed then all of the LEDs will remain steady on both of these indications will last for 10 seconds. If any errors are detected after 10 seconds they will be indicated by the illumination of the "Start", "Heated Dry", "Wash Boost", and/or "Clean" LEDs on the top display. The lock LED will always be illuminated, and does not indicate an error. Even on a machine that has no faulty conditions 815 will display on the segmented display because it is an indication of the UI software revision. If the owner starts a cycle and the machine acts as if the door is not closed there are two possibilities. A) The door switch is faulty; this can be determined by performing a continuity test with a multimeter. B) the main control board is faulty (if the door switch continuity test passes replace the control board). All of this information is in GE service manual 31-9253 for models DDT595SxJ0xx, GDF570SxJOxx, GDF650SxJ0xx, GDT655SxJ0xx, and GDT695SxJ0xx (the "x" characters are trim and color specific, but hold no bearing on the build)
@TeddyOberman
Жыл бұрын
Thanks...is there any benefit to a newer version software? My dishwasher has an 815 board but the new ones are 861. Or is there possibly a totally new board out ?
@RyanDavis87
Жыл бұрын
@@TeddyOberman I am unsusre if there is any benefit without a list of features or change log. It is possible that there is a new hardware revision of the board that also included a software/firmware version bump.
@StevenDodell-id1kg
Жыл бұрын
@@RyanDavis87 Thanks...there is always hope it might address some of the issues. I have one in my basement for when my current board blows.
@RyanDavis87
Жыл бұрын
@@StevenDodell-id1kg Agreed, I have a spare as well. My board failed twice. I wish appliances received updates more regularly. The annoyance of pressing the start button every time you open the door has burned me on numerous occasions. Although, I have already had to replaced the circulation pump, and the drain pump (x2) so I'll just settle for reliable parts that last longer than a year and a half...
@rocketdude1493
2 жыл бұрын
I couldn't get a repairman out before Thanksgiving, so decided to follow Drew's video. I ordered the control board and installed it the evening before turkey day and voila! Thank you so much. Now my wife thinks I can fix anything.
@thomasmcguire27
Жыл бұрын
It can’t get any easier given these perfect instructions. Drew did an exceptional job with closeups and plain language. The replacement board is notably more expensive than when he did the video (~$160), but it’s still attainable. Thank you, Drew, for saving me big $👍
@nandoworld
Жыл бұрын
I JUST followed your instructions in this video and saved $$$$$$! I'll be happy if the new board lasts a year +! Greatful for this video ... clear, step by step, and without all the filling 🙏🏼!
@Flarie
2 жыл бұрын
I just wanted to drop a comment and commend you for making this. I've been suffering from this 815 error for six months. Resetting the power from the breaker had been working for a while but a few weeks ago it wouldn't suffice any more. I had previously called GE and they had no idea about this, they just said there's three boards and buying all three would be almost the same as buying a new one, so they suggested I did that. I've only had my GE Profile dishwasher for less than 5 years so instead, I purchased the board from Amazon ($105) and replaced it myself following your detailed step by step. It worked like a charm. The most complicated part for my model was to reconnect the wires onto the new board before raising back into the unit. My cables were very short so it was a bit complicated, but doable. Thanks again!
@WilOsorio
2 жыл бұрын
Thank you for posting this video. I was able to use your trouble shooting instructions, and reset my panel. I shut off the circuit braker for 5 minutes, and then went to press the start button, and voila, immediately I could hear the machine filling up with water. 🙏🙏
@bobbiewhyte6343
2 жыл бұрын
My dishwasher worked twice after the reset and with this excellent advice repair video I changed the board myself in 1 hour and I’m am repair-challenged. Thank you, thank you!
@jacquierumsey2603
2 жыл бұрын
This video was great!!! I replaced the board myself and saved $800-$1000 for a new dishwasher!! This took me about 1.5 hours to do - totally worth it! Thank you Drew - your instructions were great!!!
@NovosOrdoMundi
11 ай бұрын
This video has been a lifesaver. I was able to reset the dishwasher a handful of times while I tracked down & ordered the replacement control board. Once that arrived, I was able to follow your instructions to replace it. Dishwasher seems to work fine again. Much appreciated.
@aultraman
Жыл бұрын
Thank you so much for showing us how to make this repair. It worked like a charm. My GE is slightly different (it doesn't have the metal box on the lower right hand side). The replaced board looked new but we have no easy way to test it. If someone told me the manufacturer programed the board to fail after a # of cycles, I'd believe it. Thanks again!
@WendyAnnV
5 ай бұрын
Thank you! I've been dealing with a dishwasher that sometimes works for nearly a year 😆 This worked 🤗
@royprice99
Жыл бұрын
Ordered board, followed your clear instructions and as like many others, fixed the dishwasher and saved a lot of money - Thank you!!!
@bobbiewhyte6343
2 жыл бұрын
Thank you for your help Drew. Your reset instructions worked for my GE; and I tried quite a few. I realize that the “fix” may be temporary but thanks so much for it working at least one more time. Yay, I don’t have to hand wash. Keep on helping!
@blsvids4660
Жыл бұрын
Thanks for the great instructional video! Ordered the part and made the repair in less than an hour, saving a lot money.
@jonathanhendershot9507
2 жыл бұрын
Thank you so much for the detailed instructions. I replaced the contol board in about an hour. Great to have people like you helping people how need the insight to do a some DIY home repairs.
@pamela_atx1559
Жыл бұрын
Thank you so much! Once I had all of the tools gathered it took me about 15 minutes to follow your very clear steps! I’m so grateful. You rock!
@NonstickZebra
Жыл бұрын
Resetting the power was becoming a pain, The repair shop wanted $400 to do this . Ordered the board direct from GE (FYI There is a updated motherboard with new part number) this video saved me hundreds. Ps my machine had short wires to make it a change.
@alfredeneuman6966
2 жыл бұрын
Reset worked a few times, then stopped. Got the error code and ordered the control board and replaced it. You are my hero. This will likely be my last GE though. Bought an entire kitchen set, microwave, fridge, stove, and dishwasher. The microwave went too and replaced it and not all that old.
@krlong7
Жыл бұрын
You nailed it! I had the part, followed your direction, replaced it and BOOM, back in business. Thank you.
@DanDeLong-jy8kd
4 ай бұрын
Outstanding video, very easy to follow. Thanks Drew.
@G43x93
2 ай бұрын
Saved me at least $200. Thank you for this video!!
@borincanofmr
2 жыл бұрын
thanks for your video, you just saved me $990. I bought a new one and thanks to your video I canceled the delivery order.
@cakeckthree
3 жыл бұрын
Helpful video - thanks for posting. Followed step-by-step and was able to fix my washer in 10mins. Thanks again!
@drewinaround9182
3 жыл бұрын
Glad it helped!!
@lesliechow7286
2 жыл бұрын
It helped you for about a few months. It will go bad again
@dennisjohnson4192
2 жыл бұрын
Great instructions and video! I just fixed my diswasher and works perfectly. Thank you so much. My wife will be so excited!
@ericmohner3489
2 жыл бұрын
Just had this problem on my GDT655SSJSS which was only 5 years old and not used much. Power cycling the unit would resolve the issue for a couple of cycles but eventually got the hard stop. Was able to diagnose the 815 error and make the repairs due to this video. Easy to understand and follow. Thanks!
@shrimpyd439
2 жыл бұрын
I have the same model dishwasher. Did you use the replacement part above, or was it different?
@juddbaker01
2 жыл бұрын
I ordered the board and it fixed my problem. Saved me big bucks on a new dishwasher. Thanks Drew!!
@chrisconnors-ib1gx
Жыл бұрын
A great video!! This video fixed my 815 error on my GE dishwasher. Symptoms were just as described as my problem initially went away with unplugging the dishwasher. But over time, that didn't fix the problem. Only tough part can be putting back in the control panel board as it was a very tight fit on my dishwasher.
@G43x93
2 ай бұрын
Great video. Just ordered the part. Hoping this fixes my issue.
@dagocha
2 жыл бұрын
I fixed my GE cafe dishwasher by replacing the control board. Thank you for the video.
@michaelperrine1445
Жыл бұрын
This video was extremely helpful and very well made. Thank you. I had my dishwasher working again inn 20 minutes.
@michaelperrine1445
Жыл бұрын
One thing I might add.... I had to make sure the control board personality (jumper pins) were set to my model number.... there are only two "0" or "11" for the models todate... :)
@Joe_Brig
2 жыл бұрын
Before doing that just test the latch alignment. I got the 3 beeps, unscrewed the latch, opened the door, manually placed the latch and it started working. Placed a few shims above the latch and it's all good now.
@lyltgr
3 ай бұрын
THANK YOU!!!! You just saved me a lot of $ and even more hassle! Great video!
@southerncomfort166
2 жыл бұрын
Thank you sir. Your video was extremely well done and extremely helpful. You saved me $250 or more as I was considering possibly replacing a very good washer that happens to have a very crappy board. I believe a brown out did her in. She's alive! Thanks again.
@AQNY
Жыл бұрын
Thank you so much for the detailed video! It's super helpful. It was our first time doing this but we made it well by following your guidance!
@speckulator7516
Жыл бұрын
Thanks Drew! Our exact problem with the 215 Error. It was an easy fix. Nowhere in the tech sheet I found does it even mention error codes.
@plantguy100
Жыл бұрын
Thanks Drew, big help. I had already changed the door latch which worked a few months, then stopped working. Put the old latch back and the machine again worked, but only for a few washes. I tried putting the other latch in again, but no go. At that point, I realized it is the control board (it always is), which I had already bought along with the latch. I too was receiving error code 815. Also, the light on my old board was flashing green. Need to find out what that means. I went ahead and installed the new board and now the unit is running, but I'm not confident it will last. Bad news is folks, my prior Maytag and Whirlpool Dishwashers, which were not cheap, only lasted about 6/7 years too before the control boards went. All appliances today have these control boards and they almost always go bad after 5 to 10 years. The days of 20 year appliances is long gone and that's tragic. If someone would come along a make a unit which lasted 20 years, I would pay a few hundred more for it and be happy. Spending $800 every 6/7 years for a new DW sucks.
@questionman27
Жыл бұрын
Thank you for the video. Saved me time and money.
@momnursing4
2 жыл бұрын
This was exactly the video I needed to fix my dishwasher. Thanks!
@34dawgsgo
Жыл бұрын
Excellent video all the way down to the size nut driver per screw. Have this panel ordered for a not used often GE DW. It fires up and chimes on it's own during the middle of the night and wakes me up!! Mine is not as fancy as all the controls are all on the facia. Thank you for doing.
@carriev8635
11 ай бұрын
Thank you so much! This was a great video. I am back on line and appreciate all your help.
@lucus302
Жыл бұрын
Great instructions! Very easy to follow video. Thank you!
@253ebutuoy
Жыл бұрын
Thank you for doing this video. I was able to do the reset & our dishwasher worked for several months doing the reset almost every time it needed to be run. Eventually I needed to replace the control board, which has version 8.19 listed on it. Not sure how long it'll last. The bottom line is do not buy any GE appliances, as it's now owned by Haier, a Chinese company. GE sold their appliance division to them in 2016. When we did a kitchen upgrade we got all GE appliances, which was a big mistake. Our GE stove has a light constantly on, saying the surface is still hot.
@tbobweaver
3 жыл бұрын
Thanks for the video! Dishwasher back up and running
@drewinaround9182
3 жыл бұрын
Glad it helped!!
@kelseyweingart2703
2 жыл бұрын
Great video. Easy to follow and it fixed the dishwasher!
@eyayouestifanos9746
Жыл бұрын
Very helpful. I appreciate a lot short and brief
@MUFASA-qe9nq
3 жыл бұрын
What a great and informative video. I can't wait to see more drewin around
@Miguel1485
3 жыл бұрын
Thank you for the step by step video!
@prbyangelica4284
2 жыл бұрын
Followed directions and wa la!! Thank you so very much!
@gqleo141
2 жыл бұрын
Great video, explained it completely. Thank you
@benniemac3557
2 жыл бұрын
Thanks !! Followed the video and make the repair. Worked out very well.
@RCB58Hustler
2 жыл бұрын
The only video I found that helped! Thanks!
@DG-zd5yo
Жыл бұрын
Amazing video thanks for the help!
@travelerthrulife
2 жыл бұрын
Thanks, I replaced mine with your help.
@dennisflynnsr.6888
2 жыл бұрын
Read that 815 Was the UI Software version. Against my better judgement, doubted that when I saw this (and couple other internet info) Bought new board>installed>no change in status. Quote from Sevrice Bulletin "Consumer Error Mode" On entry into C.E.M. the control reports the door status for 10 seconds. ...........The SSD (display) will indicate the UI software version (without a decimal) For example software version 8.08 will display as 808. 815 is the UI Software version. My issue? No spray during circulation cycle. Turns out I had calcified soap chunk blocking impeller. Took motor to the bench and operated in a vice. It ran/worked. Reinstalled. Back in business. Spent 110 bucks needlessly.
@ricknightengale5339
2 жыл бұрын
exactly what i needed, thanks for the video
@Corvette-nz8wb
2 жыл бұрын
Thank you for posting this very helpful video and thanks also to SNODEMON540 for the tech clarification.
@pbee6644
2 жыл бұрын
I found it much easier to lay dishwasher on its back for simpler access & board replacement as long as the hoses & power cord are long enough. Also make certain the parts you buy are specifically for your washer model number. These boards may look identical, but do not work on all models.
@snerty1966
3 жыл бұрын
With no power at all would it likely be the same board?
@villaC013
2 жыл бұрын
Thank you. this worked for me
@justfamilyfun
2 жыл бұрын
Thanks!!! Saved me.
@How-123
2 жыл бұрын
with the new board you need computer to set personality and is good idea to replace the user interface to
@joewarren929
Жыл бұрын
Is it always the control board with the 815 code or is it sometimes the user interface? I changed the door sensor latch but still have the problem of the door not being detected closed. I appreciate any help you might have. Thanks
@haydenwatson7987
2 жыл бұрын
@Drewin' Around Mine made that sound for the past week but today everything is completely dead like I had turned off the breaker. I have checked that I have power to the AC connection under the toe kick but there are no lights of any kind and none of the buttons have any effect.
@prestonjoyner8344
3 жыл бұрын
thanks
@telmnstr
8 ай бұрын
Anyone know what actually fails on the main pcb / board? I have mine on the bench powered up. The dc voltages all check out. It looks like the conformal coating that GE puts on the pcb might be causing the vias to the other side of the board to corrode? Already recapped it that didn’t solve.
@telmnstr
8 ай бұрын
Replacing the 3 electrolytic capacitors on my control panel PCB seemed to totally fix my dishwasher without paying for new boards. It was between states of no lights/dead and 3 beeps wouldn't start as if door was open. The switch/latch for door was fine on mine.
@uweschroeder
2 жыл бұрын
A little tip before taking anything apart on any repair: pull out your phone and take a picture of the electrical connections. It gives you a reference for putting it back together properly,
@kdeh21803
5 ай бұрын
What is WD21X24901R??
@longterm11581
6 ай бұрын
please see Ryandavis 87 comment below/ THIS IS BAD INFORMATION!!!!!!!! 815 is not an error term. You must check the control board for 14 volts to determine if it is bad. 815 is just the software number. Based on this guy, I changed the control board and it was not the problem. It is all over the internet that 815 is an error term, except nowhere in the GE literature.
@adrianoevola4937
Жыл бұрын
Hi, I had the 815 error code and I replaced the board. Still not working. Is there something else it could be?
@NonstickZebra
Жыл бұрын
The fact that I could turn off the power for awhile and then run a cycle showed the the door switch was working. if that's not happening I'd start there.
@christophersmith8172
Жыл бұрын
What is your green wire on the bottom connected to at 4:44
@253ebutuoy
Жыл бұрын
It's the ground wire.
@bobseph
Жыл бұрын
I have replaced the main board and ui board and things are on now but the controls are not working as normal: kzitem.info/news/bejne/0oKE0ol9soyWnW0 Any suggestions???
@Schlitzrock15
2 жыл бұрын
JUNK! Do not buy these dishwashers! GE should be ashamed of producing such a crap machine.
@AmericanConstellation
Жыл бұрын
What's sad is that GE used cheap electrical components to build this board. You'll be lucky if this board lasts for two years. What a joke!
Пікірлер: 87