*Revolutions per minute* The French: *heavy breathing*
@tamim3463
5 жыл бұрын
hit the nail on the the coffin, great explanation
@franklettering
4 жыл бұрын
TIP Top video !!!. Clear and precise. Without the usual KZitem faff.
@pdufusc
2 жыл бұрын
simple and to the point... good job
@kimmi5925
Жыл бұрын
This was so helpful thank u so much
@brendenallen9451
3 жыл бұрын
Thank you soo much that helped a lot
@bijouxmathew1092
3 жыл бұрын
Thank you That was helpful
@MuhammadAli-iy4qn
4 жыл бұрын
I want to make 3k rpm with flywheel could u plz hlp sir.
@muthukumarj7246
6 жыл бұрын
super explanation
@f1reguy587
Жыл бұрын
I guess its the same with pulleys? Except the ratio would be circumference output / over circumference input? But is the measurement taken from the outer diameter or the inner diameter of a v belt..
@kidnabi2388
3 жыл бұрын
Thank you my good sir
@REVNUMANEWBERN
5 ай бұрын
I want to convert sprocket to sprocket with chain to pulley to pulley with cog belt, is there a conversion calculator anywhere that I can input the chain info & get the equivalent ratio in a pulley setup?
@wahidsaifudeen1651
Жыл бұрын
If less teethed driven (output) gear messed with a drive (input) gear mean more roation of output gear? That is what I understood. Pls Correct me if I am wrong.
@PrashantSannake
2 жыл бұрын
Spur Gear are generally used for gear ratio of........?
@kayakMike1000
26 күн бұрын
Use ratios of prime number of teeth. The gear teeth will wear evenly and therefore slowly.
@luqmaankhan6241
2 жыл бұрын
If the input gear were the smaller gear would the format change or might you swap the numerator or denominator?
@outofahat9363
2 жыл бұрын
the formula remains the same (output teeth over input teeth) but of course the gear ratio will be reversed (8:5 instead of 5:8) but not because you changed the formulas but because you physically changed the input and output gears
@luciusjoeterry7526
4 жыл бұрын
This is a nice vid
@unexpectedme9992
2 жыл бұрын
i have no clue why the other videos has so many explanations, Formulas etc. i mean why though? pls tell me.
@harrytaylor4360
2 жыл бұрын
Is out/in out:in really convention? I'm given a ratio and an output, and I'm being told to multiply them together to get an input... That doesn't look right!!
@OKFrax-ys2op
3 жыл бұрын
So if you had 100 foot pounds on the large driven gear what would the result be on the smaller output side? What is the formulation for that?
@mrbuddyvlogs7316
3 жыл бұрын
A number
@OKFrax-ys2op
3 жыл бұрын
@@mrbuddyvlogs7316 Precisely you mathematician you
@mrbuddyvlogs7316
3 жыл бұрын
A number in between 1 and 10,000
@darrenrich4075
2 жыл бұрын
62.5
@Vgk36
10 ай бұрын
I don't get it. What is the speed ratio of an input gear with 36 teeth meshed to a gear with 20 teeth? The only answers are A9:5 B 1:0.56 C1:1.8 Using your formula I've got 4:7 ??? What am i doing wrong ?
@oyo2394
3 жыл бұрын
Thank you
@canned_doughnuts_5222
6 жыл бұрын
Seems legit
@hindicomedy249
2 жыл бұрын
Nice
@johnrussell3755
6 жыл бұрын
thnx..u made my day
@valens682
7 ай бұрын
Thx!
@rizwanjavaid1443
3 жыл бұрын
Good
@bassemhassan6985
3 жыл бұрын
2021
@bonolomfelang4582
2 жыл бұрын
calculate cpascals principle
@redtail1.
Жыл бұрын
Ok off topic but why do nerds always hold their pens in a weird way?😅
@nathankaseygrant
4 жыл бұрын
O.J. Simpson is innocent
@nickguziak5405
4 жыл бұрын
👏👏 such wise words.
@bordwithasword
4 жыл бұрын
That is sin
@murriretro430
2 жыл бұрын
The Glove Didn’t fit Lol
@kylecountryman4794
6 жыл бұрын
inless property wayes of pions up counts get study right
@ot2uv
4 жыл бұрын
Why. 25÷5 and Why. 40÷5. Please explain
@bledriper8299
4 жыл бұрын
in simple terms: we are trying to write 25/40 in a simpler way ( and easy to visualize and understand), both numbers 25 and 40 can be devided by the same number 5 .
@daundaground2897
4 жыл бұрын
@@bledriper8299 thnks for help^^
@wahidsaifudeen1651
Жыл бұрын
You can divided by 10 too, if you want. That will give you 2.5:4. Means every two and half rotation of input gear is equal to 4 rotation of output gear, which is exatly 5:8
Пікірлер: 52