It is good that I did not do as in the video, there is only one need to remove the upper tank and wipe the contacts, liquid got there!
@clarinkeirvyllerobinm.5296
3 жыл бұрын
what contacts
@zlatan4083
3 жыл бұрын
I have “no atomiser” problem and one of the 3 pins is stuck in a pressed position. Any help? Thanks
@RedzoneJFF
3 жыл бұрын
Just let it dry bro, and change the coil.. Done 😄😄😄😄
@babik4617
3 жыл бұрын
I have this problem it is working
@babik4617
3 жыл бұрын
???
@RedzoneJFF
3 жыл бұрын
@@babik4617 its hard, take the easy way 😁
@babik4617
3 жыл бұрын
@@RedzoneJFF ok thanks man
@RedzoneJFF
3 жыл бұрын
@@babik4617 thanks bro.. For this video, good work
@ferdinandjoshuagarcia5452
4 жыл бұрын
Whats that liquid stuff that you use when soldering???
@masterfixgr
4 жыл бұрын
Flux. Helps soldering.
@edwincarter5932
3 жыл бұрын
you make soldiering those small places look so easy. I can never do that. What is that liquid you use and what type of soldiering iron you have?
@masterfixgr
3 жыл бұрын
It's flux. Helps in soldering. I use a Hakko FX-888D soldering station.
@azmainali5593
2 жыл бұрын
Where is your shop I’m from bangladesh
@cobbyh9010
4 жыл бұрын
What size alen wrench is that for the side screws?
@masterfixgr
4 жыл бұрын
You will need a hexagon screwdriver H1.3
@sagevoix5873
4 жыл бұрын
so just clean the join?
@masterfixgr
4 жыл бұрын
Yes if there is only liquid. If there are corroded components and pads you should remove corrosion and resolder
@afriyantobasabanuara5466
4 жыл бұрын
I have problem.. the pin number 3 chip... Was missing... Where do i have to jumper sir... Thanks before
@masterfixgr
4 жыл бұрын
Sorry, I don't have an Aegis Boost right now to check
@seanjeanricmontanano1841
4 жыл бұрын
How to fix my boost if it always say, atomizer short.
@dafikido
4 жыл бұрын
So it's not a waterproof pod?
@masterfixgr
4 жыл бұрын
Theoretically it is. But nothing in this world is perfect :)
@ДенисОчеев-ъ4б
2 жыл бұрын
hello, tell me which microcircuits are responsible for reading the atomizer?
@masterfixgr
2 жыл бұрын
Everything in the output circuit takes part to read the coil. The processor sends a low volt signal to the mosfet driver. Mosfet driver passes the signal through an inductor to the mosfets. Finally, the signal goes through a current shunt resistor to the coil. A current sense monitor amplifies the voltage drop at the shunt resistor and sends it back to the processor. The firmware calculates the resistance of the coil from the amount of voltage drop.
@ДенисОчеев-ъ4б
2 жыл бұрын
interested in the location of the mosfet driver and shunt resistor. thank you very much in advance.
@masterfixgr
2 жыл бұрын
@@ДенисОчеев-ъ4б IC chip marking UP9636P is a buck converter with integrated mosfet and gate driver. Shunt resistor marking R002
@ДенисОчеев-ъ4б
2 жыл бұрын
@@masterfixgr thank you very much
@fishermanjoe9324
4 жыл бұрын
Hello sir, I just watched your video and my aegis boost has a different problem. My aegis boost lost backlight on the screen and the fire button does not work anymore. Hopefully, you can help! thank you so much.
@masterfixgr
4 жыл бұрын
Screen and fire button must have voltage in order to work. No display and no fire button means no power on the board. You should trace the positive battery rail to find out where the voltage is lost.
@annavergara2902
3 жыл бұрын
I do have desame problem but is i don't know what exactly happen i just clean the pods and the juice that is leaking and when i put back the pod it happens "No atomizer" i used thi last night i just clean it 😭 What did i do?
@masterfixgr
3 жыл бұрын
Check if the coil is properly seated. Check if atomizer contacts on the pod are springy or stuck in the pressed position.
@gavingriffith3359
4 жыл бұрын
Let me send you mine and a check
@casuallyarguments3577
3 жыл бұрын
How to prevent the vape from leakage???
@masterfixgr
3 жыл бұрын
Unfortunately, you can't with this pod.
@casuallyarguments3577
3 жыл бұрын
@@masterfixgr any solutions please???
@asakura069
4 жыл бұрын
Sir can you help me ? My boost always show “battery weak” or “no atomizer” even if its full charge It will fire for around .3 seconds but after that it will stop and show “battery weak” Thank you so much for your help
@masterfixgr
4 жыл бұрын
If there is liquid inside follow the steps in this video
@asakura069
4 жыл бұрын
Camber thank you so much sir godbless 🤘🏽
@asakura069
4 жыл бұрын
I already follwed whats on video sir but still the same I tried to lower the wattage to 30 and its fine but still not normal , i still get the message “battery weak” SOMETIMES Can you pls recommend me what’s next to do ? cause i cant use it as a normal vape , Thank you so much
@asakura069
4 жыл бұрын
I need to lower the wattage everytime the battery level goes down , can you guess what is wrong ? Thank youu
@JohnDoe-ho6mq
3 жыл бұрын
Christel aypa Uuhhmm... The next thing to do should be simply throw - out that piece of electronic junk and head to the store for cigarettes and lighter. Not only is this a fool proof remedy to your cuhwagmjre , it is also a cost effective (cheaper in the long run ) operation.
@jhonnykurara
4 жыл бұрын
sir can you help me wich ic that respond to reading atomizer..thanks
@masterfixgr
4 жыл бұрын
It's not that simple. Atomizer is connected to a shunt resistor. To read the atomizer, processor sends small current through the buck/boost converter (2 power ic and an inductor) to the shunt resistor. There is a tiny voltage drop which is picked up by a shunt monitor. This tiny voltage is amplified by the shunt monitor and returned to the processor. The processor calculates the resistance from this voltage drop (Ohms law). If any of the above IC's is faulty (including the processor) then the atomizer can't be read. Also the supportive passive components of these IC's could be faulty (capacitors, diodes, resistors).
@jhonnykurara
4 жыл бұрын
@@masterfixgr k
@vashcorler
4 жыл бұрын
Sir, may I asking what power system should we use when testing board before install? I’m still a noob on pcb
@masterfixgr
4 жыл бұрын
Any variable voltage/variable current bench power supply will do. My power supply can output up to 60A but you will rarely need above 5A.
@jhonnykurara
4 жыл бұрын
@@masterfixgr thanks sir yes indeed its that not simple, thanks for the explanation.
@dxversions
4 жыл бұрын
My boost doesn't turn on..the charging is ok
@masterfixgr
4 жыл бұрын
What is the voltage of the battery?
@faceoff9521
3 жыл бұрын
@@masterfixgr how to find out?
@masterfixgr
3 жыл бұрын
@@faceoff9521 Measure battery voltage with a multimeter. Of course you must first disassemble the device.
Пікірлер: 58