😅I was very excited when i found this series, know so called tutorials besides this one explains really anything about the process. After part 2 i was ready to learn how to start actually cutting stones just be to let down by the absence of part 3. Thank for detail of 1 and 2. Back to my search for the rest of the information.
@jossmaxwell00
3 жыл бұрын
Like any machine, regular cleaning and maintenance will help to preserve and give longevity of use. Thank you Cliff for this video.
@VintageTimeGems
3 жыл бұрын
Thanks Joss....
@musonda.mlwelele5689
3 жыл бұрын
Hi cliff...I always injoy your videos, thanks for teaching & sharing your professional you are great,greater & greatest gem cutter I surlut for you.from zambia🇿🇲🇿🇲Africa
@VintageTimeGems
3 жыл бұрын
Thank you for your kind words.
@musonda.mlwelele5689
3 жыл бұрын
@@VintageTimeGems You are we'll sir
@BigCroca
3 жыл бұрын
nice to see you upload again :)
@roxxie0819
2 жыл бұрын
Very informative series of videos Thank you For taking time and patience I hope u will add more of these “how to for dummies” series of detailed videos
@silverback5033
3 жыл бұрын
Hi Cliff, I find this series really interesting. I am recently retired and have taken up fossicking and once I have a sufficient amount of knowledge and raw material I would not mind having a go at some simple cutting. I am going to start with trimming & polishing some rocks first before deciding if I purchase a faceting machine, so for me your videos are spot on target. Keep Safe & Keep Rockin
@VintageTimeGems
3 жыл бұрын
Thanks silverback, that's the best just trim and polish by hand. If you enjoy that you can always facet later. Cheers Cliff
@jeffholmes1362
3 жыл бұрын
Nice Cliff. Thanks for making this series
@VintageTimeGems
3 жыл бұрын
Thanks Jeff
@johncrumpley8702
3 жыл бұрын
Excellent video, Cliff. Thanks for taking the time to share your knowledge with your many fans. UltraTec machines don't use a belt, opting instead for a hard rubber "cone" to transfer the motor's energy to the vertical shaft. However, during routine maintenance one needs to give it a little attention.
@VintageTimeGems
3 жыл бұрын
Hi John, I noticed the V2 was direct drive. I think that is a good idea. I liked how the height could just wind up and down also. Other aspects seem cumbersome...
@TheCaptainShow
3 жыл бұрын
very interesting , with a good information , take care , have a good day
@littlehills739
Жыл бұрын
21:00 try using 2 beads linked with cored push them in hole to join then wrap in-front of the bead to lock it utube spear gun replacement bands to find how
@scotth.487
2 жыл бұрын
This was very helpful!! Thank you!
@jamesfloyd722
Жыл бұрын
I suggest plugging the end of the quill and filling the quill socket with a gun cleaning solvent, using a qtip to agitate anything that may be on the inside walls. Then use denatured alcohol to spray out thr socket and wipe with your liquid parafin lubricant.
@TonysGemDesignswithGCS
3 жыл бұрын
Great video. Unfortunately I don't clean to the same level as you. Note, not all machines can be disassembled to the same extent as yours, some you shouldn't otherwise you can upset the calibration/level of the machine. On the Halls , the swing arm pivot, the head to mast mounting block etc should not be taken off because it will effect the level of the head to the laps. I scrounged some oxygen tubing from a hospital for my belt. Some heat, some CA glue it works well and is quieter!
@markturner9293
3 жыл бұрын
very informative thankyou
@VintageTimeGems
3 жыл бұрын
Thanks Mark.
@richardlasky9184
2 жыл бұрын
Hi Cliff. Your videos are great and very knowledgeable... 👍 With the amount of time a person spends faceting one gem..- Do you sell your gems for a normal price or just lower the price to get them all gone quicker?? 🤔
@tommcelroy6975
Ай бұрын
In 3 years you never made a part 3?
@onebadwolf9123
2 жыл бұрын
Thank you for the great videos! As a fellow watch guy, I figure you'd be the perfect person to ask, have you ever removed scratches from a sapphire watch crystal?
@Protocol-X
Жыл бұрын
I noticed that the hewer models of machines always get more expensive, but also less powerful. Is there a suggested RPM range to look for in a machine? The older ones seem to go to 3000rpm but newer ones are around 1200-1500
@a.aldukhail8696
Жыл бұрын
where is part 3
@clementwuthrich655
3 жыл бұрын
Hi Cliff, great video again. how do you call those little aluminiun joining "drumette" for the belt, mine snaped and don't seems to be finding thoses little parts. thanks in advance for your time. Take care.
@VintageTimeGems
3 жыл бұрын
I bought these locally from a place that sells belts and pullys.
@faneshbhaisare9709
3 жыл бұрын
Sir please see.watu atos videos once he is cutting gems in other way by a single motor and a single tool can you how it is the person don't know english
@littlehills739
Жыл бұрын
7:15 weed wacker whipper snipper cored bent in 1/2 pull through cloth or 12g shot gun bore snake /// utube home made bore snake
@gabriellecusack4389
Жыл бұрын
My husband loves your videos. When I am listening, no offence but I do wince when you pronounce debris as Deb-riss. It should be De-bree.
@LapidandoPedraseGemas
3 жыл бұрын
Show
@KyawOo-nl3ls
2 ай бұрын
price
@askndeniz5781
Жыл бұрын
Where can I buy this machine? do you have the disk and machine? or phone number or address..can you give me?
Пікірлер: 34