I found this very helpful, Ground-faults are a nightmare....
@MrPinkWing
2 жыл бұрын
Thank you so much for all your videos! You explain very clearly. I'm doing my first contract as electrician on a sistership, so your videos are super usefull for me!
@leckyjake
2 жыл бұрын
thank you for watching
@piinheiiiro
Жыл бұрын
You're expert in power generation .
@sal7777777
4 ай бұрын
Great video, I really like the content you make specially the troubleshooting videos, they are fantastic. Is there anything you can do to improve the technical editing quality of the videos though, the audio levels are really extreme, on some parts the audio is really low and others really high, sometimes it makes it hard to watch them.
@adamdeguzman3238
2 жыл бұрын
Thanks for sharing your knowledge! ❤️
@Anna-nr9kk
Жыл бұрын
Thank you, mr. Jake!
@varatharajan1837
2 жыл бұрын
Nice troubleshooting thanks for sharing your valuable knowledge thank you very much
@leckyjake
2 жыл бұрын
thank you for watching
@elevationtechvlog3474
2 жыл бұрын
Hello sir your work is very difficult and dangerous...be careful always god bless...
@ricardopastor7488
2 жыл бұрын
This video is very helpful, thanks to making this kind of video..
@edwardborja3280
Жыл бұрын
Thank you sir for this vedio
@gohanmusic4842
6 ай бұрын
excelente
@geenumaxy9370
Жыл бұрын
ur good man nice troubleshooting
@nagrerelax5602
Жыл бұрын
Nice one sir Jake
@kennethlobo4420
2 жыл бұрын
Great trouble shooting video.
@alterator
Жыл бұрын
Fine
@sudhanshusaini4968
2 жыл бұрын
Sir plz share more troubleshooting videos on generator
@dilsara5429
Жыл бұрын
❤❤ Thank you
@jorgebravo415
5 ай бұрын
Flink ship elektriker ⚡⚡⚡⚡
@joseenricoaguila5218
2 жыл бұрын
thank you so much, very helpful
@leckyjake
2 жыл бұрын
thank you for watching
@kevin00861
2 жыл бұрын
Thanks a lot brother for your amazing videos, If I may ask please, Is it safe to unplug & plug terminals to analog control modules while it's still live ?
@lebrassedidier8258
2 жыл бұрын
Great Video:)
@leckyjake
2 жыл бұрын
thank you for watching
@waynep343
2 жыл бұрын
Did you eyeball the inside of the connector body for casting roughness. Think about if it can be done to remove the casting roughness. Use some 3m# 27 fiberglass cloth tape on the inside of the fitting and around the harness..
@leckyjake
2 жыл бұрын
i did used the thermal cloth tape for insulating the wires
@afsalali3961
2 жыл бұрын
Pls do one detail video about bow threster sir..
@leckyjake
2 жыл бұрын
keep on the list
@tayzaraung4843
Жыл бұрын
Hello sir,guide me what book is good for eto.
@rafaelhijara9534
2 жыл бұрын
Sir I have also a problem of low insulation of 24 volts alarm..but during underway situation the alarm was okey..and sometimes my 24 volts insulation indicator is flactuating.. Is the low insulation indicator have a problem.?
@leckyjake
2 жыл бұрын
it depends, you should start tracing whenever it is active.
@rohilkumarsaini9126
2 жыл бұрын
Thanks you so much sir for sharing this wonderful and knowledgeable video.
@leckyjake
2 жыл бұрын
thank you for the support
@elevationtechvlog3474
2 жыл бұрын
Always remember that we cannot see the current...
@afsalali3961
2 жыл бұрын
Thankyou sir.. 👍🏻👍🏻👍🏻👍🏻
@electrotechtv2109
Жыл бұрын
Thank you for sharing sir
@ВикторияЛирник-я9и
2 жыл бұрын
Thank you So mach. This is good Video
@islemghz3780
2 жыл бұрын
Hey hope you are doing well, I'm an instrumentation engineer (will graduate this year) i want to ask you if it is possible to work as an eto with my engineering degree (if not then please guide me)
@leckyjake
2 жыл бұрын
hi, it is always depend on your country. you should check the maritime authority that governs the licensing for such profession.
Пікірлер: 40