Top hose is not a pulse hose its a vent , helps to compensate when the air filter become clogged it helps to regulate the movement of the metering diaphragm, the pulse line would be on the fuel pump diaphragm side…!
@spankranchgarage
Жыл бұрын
I agree with you! I pinned this comment so others can learn from it. Thanks!
@alexcompton9108
7 ай бұрын
That explains the extra pipe lol
@shaunwoodcock6381
2 ай бұрын
Great video I've tried putting new diaphragm kits in my stihl ts 400 carbs but cant get them too run right I've sprayed all holes but fuel coming out from air filter what am I doing wrong many thanks
@Fraishe
2 ай бұрын
You just saved my Stihl Ts410. Had an issue with my Stihl saw where it would start but only run for about 3 seconds then it would turn off on its own. Did exactly what you did, cleaned the carb, purchased a carb rebuild kit, cleaned THE FUEL PICKUP/ AIR VENT & all the fuel lines. My fuel pickup/ air vent was super crusty and the debris caused a bad seal, and that was my problem. So i basically cleaned my whole fuel system, put everything back together, tuned the carb at a standard setting of 1.5 turns out for both H & L set screws, now she runs like im her first owner. God bless your vid and thank you for showing us how its done🙏💯
@Col.Canuck
Жыл бұрын
Thanks for taking the time to do this. I actually started a small repair business because of this video. You changed my life and I will always be greatful to you. Best regards, Aaron from Toronto Canada 🇨🇦
@spankranchgarage
Жыл бұрын
That's incredible good for you! Thanks for the comment!
@Prod.yungdoddi
2 жыл бұрын
Love the accuracy of how many screw/bolts that get dropped I find it entertaining someone else struggles with this as much as me.
@markgreen4946
Жыл бұрын
Good video, very helpful, they are a great bit of kit, they are just as good as well with cutting steel as well, we use them for everything in demolition, cables, steels, concrete
@spankranchgarage
Жыл бұрын
Yup! Love it I keep a metal blade in it most of the time
@spettro9
2 жыл бұрын
T27, not T25. Yes, it will work sometimes, but it's also the perfect size to mess them up if they're seized a bit.
@tuckermartin5559
2 жыл бұрын
This is honestly such a classic. Had to revisit
@spankranchgarage
2 жыл бұрын
Makes you wanna buy a demo saw doesn’t it?
@tuckermartin5559
2 жыл бұрын
@@spankranchgarage woulda made cutting that axle a whole lot easier!
@DizzyMotoz
3 жыл бұрын
Your a king wish u could fix mine it starts and just bogs out
@ASQUITHZ9
Жыл бұрын
Nice job! well done, a good example of the American can do will do society!
@CarlosGarcia-p9r
3 ай бұрын
Muy perfecto tu video algo bien te mereces 5 estrellas soy mexicano pero te entiendo perfectamente me ayudó mucho tu video que diga video tu experiencia es algo bien sigue así te seguiré todos tu videos.
@chrisgoddard4120
11 ай бұрын
My cutters working but as soon as I start cutting it loses power any ideas on what it could be? Cheers
@sessman55
7 ай бұрын
What’s the part number for the metering diaphragm?
@CarlosGarcia-p9r
3 ай бұрын
Se los recomiendo amantes de la construcción así como yo 100 y pasaditos
@dannybowman7978
3 жыл бұрын
Maybe someone can help I have a ts420 concrete saw it runs perfect until I pick it up to use it and then it turns off
@marshallb3308
2 жыл бұрын
Solid video 👊🏼
@DonaldKirkland-r3w
Күн бұрын
Is that a chinese saw.
@stewartprice8881
2 жыл бұрын
thanks for sharing
@garylatto4191
Жыл бұрын
Hi come across your video, mine struggles to start if I've got less than half a tank of fuel despite a new fuel filter and fuel line, any ideas please would be appreciated 👍
@spankranchgarage
Жыл бұрын
Sometimes that means there is a pinhole in the fuel pickup line... but looks like you already replaced that. I am not too sure sorry!
@garylatto4191
Жыл бұрын
@@spankranchgarage ill double check the pipe and grommet. Cheers for reply 👍
@70soundwave
3 жыл бұрын
My Carb also only has 1 adjustment screw for the low I am guessing. I thought it was missing one and I am about to order a new carb because I thought it fell off. I got this machine used BTW. The new carbs have a H and L adj. screw. Why is there only one on this one? Thanks
@spankranchgarage
3 жыл бұрын
70soundwave Mine only has 1 screw too. I expected it to have both like I probably said in the video. I too, bought a Chinese carb, that has a H and L, but never used it. I am happy with how it runs with the OEM carb. If yours runs well on the OEM carb I wouldn't change it.
@luvegg7890
2 жыл бұрын
Hiya, I think it's because the newer saws have a rev limiter built into the coil so a Hi mixture adjustment isn't needed.. The older saws need the Hi adjustment to adjust the max revs..
@luisjorge7344
18 күн бұрын
Gasolina with oil? Mix
@spankranchgarage
18 күн бұрын
Yes. 32:1 or 40:1
@jcfrances1084
3 жыл бұрын
Im curious how and if I'll know the carb needs adjusting?
@spankranchgarage
3 жыл бұрын
If the engine surges at full throttle, typically you will turn the high jet “out”, counter clockwise. If it bogs at full throttle, smokes a lot, and doesn’t run “crisp”, turn the high jet in. Turn in 1/4 turn increments and see if it gets better or worse
@CheddarCheeseBandit
3 жыл бұрын
T27 torx
@olavomartini674
3 жыл бұрын
👍🏼💪🏼👍🏼👏🏻👏🏻
@CHIBA280CRV
2 жыл бұрын
Fantastic I will do the same to my used ts400 when I receive it.. thanks for sharing your informative video 👍👍👍👍👍
@Gemini_Beautify
2 жыл бұрын
Always love seeing you fix what you got instead of giving up!
@stevenwatson2699
3 жыл бұрын
That beer will make it run better?
@ASQUITHZ9
Жыл бұрын
There was a joke from a comedian called Jethro who told a story about a guy who broke down and he asked the AA bloke what was wrong and the AA bloke answered oh yea err "Shit in the carb" and he answered "OH! right! how often do I have to do that then"
@herbertvonsauerkrautunterh2513
3 жыл бұрын
I'm looking at buying a used one of these.. I see all posts are available fairly cheap. I think it may be worth it. Either this or a few more $$ for a ts800
@smithy2k13
Жыл бұрын
do u have a vid on this saw bogging down please mine doing it naw and dont no wats rong
@spankranchgarage
Жыл бұрын
I dont. But check your jet tuning and also inspect your fuel lines closely. Any leaks will draw in air and create a bog
@jcfrances1084
3 жыл бұрын
Best video out there. Gimme a day and I'll report back!
@72cabana
2 жыл бұрын
Awesome video.!! Thanks!
@abarmagh1497
2 жыл бұрын
mine was not starting so took off carb and cleaned and started fine, switched it off and now not start at all??
@s.i2898
Жыл бұрын
Was it turning over?
@mankillsquare
2 жыл бұрын
Great video. So, my saw has started refusing to start up. I’ve got spark, got a new plug in anyway. Air filter isn’t too old. So I’m guessing maybe the carb. But I didn’t see what was actually wrong with your carb? Did you establish what it was or are you just putting it down to needing a good clean?
@spankranchgarage
2 жыл бұрын
I didn't physically see any blockages but that isn't too unusual for these small carbs. Its possible the needle was sticky or something else too. Good luck with yours!
@mankillsquare
2 жыл бұрын
I went out to the garage last night for some beers and thought I’d give the cord a quick pull for the hell of it. Heard it catch a little, flipped the choke to half and give it another and off it went! So I decided to not waste the opportunity and started splitting some bricks I needed! Don’t think the neighbours were too happy. Hopefully it will start later today too. Thanks for your reply, it was good luck for me 👍
@shaunwoodcock6381
11 ай бұрын
I've put stihl ts 400 in ultrasonic cleaner rebuilt with new diaphragm kit but wont tick over I've turned tick over screw in as far goes what am I doing wrong carb is spotless do you change welsh plug
Пікірлер: 51