Thanks for the video! I just fixed my wife's, different model, different problem. Apparently a tiny wire or a hair of solder was contacting something else an was shorting out one half of the unit. Scrubbed the boards with a brush and alcohol and it seems to be working fine now. My wife is a stylist and she's probably been through 3 of these GHD irons over the years. She always threw them away and bought a new one. If I knew you were out there I would have sent them to you!
@Trevs-Shed
4 ай бұрын
Hi Yes. All our repair services are linked to below. www.ghd-repair.co.uk/shop/repair_services/
@Indylimburg
3 ай бұрын
@@Trevs-Shed Thanks again. Just fixed 2 more, one this same model!
@Adrianburalli20
Жыл бұрын
Great my friend 🙌
@khushboosaini1758
Жыл бұрын
My hair straightener wire is burnt when I put it on heating then I immediately turn off the switch. Now what should l do now buy a new one or repair it at shop because it is new I am using that straightener for third time. Plz reply
@omerkhan7401
Жыл бұрын
Our straightener is on red button n giving only beep when we switch on It was overheated n now not working
@Trevs-Shed
Жыл бұрын
What model?
@belindadumpleton6537
4 ай бұрын
Hi could you do a repair for me?
@Trevs-Shed
4 ай бұрын
Hi All our repair services are linked to below. www.ghd-repair.co.uk/shop/repair_services/
@Ruff_Ambassador
Жыл бұрын
I accidentally broke the on off switch on the circuit board while using a terminating screwdriver to take it off but the thing snapped. It seemed really hard to take off. There's 4 tabs but pressed them in and nothing happened. Is there a special trick can't see it in your video. I can't find any replacements for just the switch do I need to replace the whole circuit board?
@Trevs-Shed
Жыл бұрын
Contact me through ghd-repair.co.uk I can sort out a switch casing if that is what you have broken, the switch prises apart at the sides and then the cover lifts off exposing the contacts. Include a picure showing the damage.
@gerardwebb-kd3xv
2 ай бұрын
Ghd straighteners mk5 no heat bleeping sound but no red light have checked thermal fuse heater pads resister r8r11 cable and are all ok what do you think thanks
@Trevs-Shed
2 ай бұрын
@@gerardwebb-kd3xv thermistor or pic processor
@DeanG85
Жыл бұрын
My wife’s turn off when the cable turns around at the base. Will this likely be new cable needed or loose connection. Do u have a video of these repairs.
@Trevs-Shed
Жыл бұрын
Hi. Change the cable and possibly the socket if required. All the required information is on my website. ghd-repair.co.uk
@DeanG85
Жыл бұрын
@@Trevs-Shed thanks.
@SamDaMan101
Жыл бұрын
Hi there, my girlfriends beloved GHD gold straighteners wouldn't turn on one day. No lights or noise. I replaced the cable with a brand new one, still no luck I then replaced the thermal fuse with advice on various online platforms. The straighteners now turn on but constantly flash and beep and won't heat up. Any advice would be much appreciated!
@Trevs-Shed
Жыл бұрын
Tut tut, online platforms... Go to our repair guides www.ghd-repair.co.uk/guides If the thermal fuse had actually failed I would say the irons overheated due to a faulty thermistor, that bleeping is probably caused by the thermistor. Check and replace R8 and R11, change the element with thermistor, all available from our website. Our use our repair service £26.94
@SamDaMan101
Жыл бұрын
@Trevs Shed Thanks for the advice I will order the thermistors and take it from there. Failing that I'll send it the pro to sort it out lol thanks again.
@royandrews7829
Жыл бұрын
How do I get in contact with you for a repair on ghd max straighteners thanks
@Trevs-Shed
Жыл бұрын
Hi Through our website, link in the description.
@tarafowler-dalebout4643
10 ай бұрын
If I send mine to you, are you willing to try to fix it? Obviously, you can charge me what you think is fair to Fix that this is something you are willing to do. Let me know, thank you. I believe mine is having a similar problem. It turns on and off as I lift it to use it on my hair, therefore it beeps several times as the heating element is going on and off. Thanks
@Trevs-Shed
10 ай бұрын
Hi All the repairs have a fixed fee. www.ghd-repair.co.uk/shop/repair_services/
@NancyGarcia-om6is
3 ай бұрын
My GHD curling iron has a red light blinking. Is there a fix for that?
@Trevs-Shed
3 ай бұрын
What's the model number.
@1conkers1
Жыл бұрын
Hello……. Do you do repairs for people? We have a set of cloud 9 C9-L1.2 that just keep bleeping and not heating up.
@infinitelady
Жыл бұрын
Can you repair other branded straighteners too?
@Trevs-Shed
Жыл бұрын
Sometimes Cloud 9's can be repaired but other than that no as no parts are available.
@yourshoppingguide8371
Жыл бұрын
Hi.. I once used ghd in my extension which is not very long in length Does it cause some sort of damged?
@Trevs-Shed
Жыл бұрын
It can do, any sparking from a dodgy wall socket or extension lead may cause the irons to fail. Repairable though.
@rimetea4569
5 ай бұрын
Hello, when i plug in the ghd one plate instantly heats up and jumps the fuse. What can the problem be? I would send it to you but i’m to far(2500miles) :) . Thank you
@Trevs-Shed
5 ай бұрын
Hi. What does "jumps the fuse" mean?
@rimetea4569
5 ай бұрын
@@Trevs-Shed it’s series s7n261 with those mechanical fuse, when it over heats the small bended plate pops. But after reading more of your replies and videos, it seems it’s pcb error. The instant heating without to be started from button. Do you sell pcbs?
@Trevs-Shed
5 ай бұрын
@@rimetea4569 Yes, all GHD Gold and Max irons require PCB modification and other work. You can not repair this model yourself. Sorry.
@rimetea4569
5 ай бұрын
@@Trevs-Shed do you have any clue if we can find new pcb’s? We have lot of this ghd :(
@Trevs-Shed
5 ай бұрын
@@rimetea4569 Hi No genuine spares are available for any GHD. GHD do not sell parts and they do not repair anything! A replacement PCB will not help you as the value of the PRT in the elements varies and is set up with software. Every Gold/Max PCB in existance requires the modification that we carry out. We also wrote new firmware to allow us to match elements correctly to the PCB. I don't know what to say to you. Other than sending them to me for repair there is nothing you will be able to do.
@gpf5204
11 ай бұрын
They may be quality, but for what they have inside they are too expensive.
@johnharris5028
Жыл бұрын
Hi what size are the resistors ? where did you get them from you said yours were better quality Thanks
@Trevs-Shed
Жыл бұрын
The link to buy them is in the description...
@johnharris5028
Жыл бұрын
@@Trevs-Shed hi I give up where is the description ? I am new to this Thanks
Пікірлер: 41