Any tutorial on GHK M4 mags fitting problem into magwell? Some fit perfectly, others have to be puled with force
@reff942
9 ай бұрын
Since I never encountered this issue I have no way to replicate it.
@alexanderfrazier8840
Жыл бұрын
Solid vid.
@hubi143
Жыл бұрын
hey bro nice video. what do you call the tools you used? like the pin pusher etc. im newbie i ordered ghk mk18. im searching video like this to prevent my ghk to have problem.
@reff942
Жыл бұрын
Hey, welcome to GHK master race family! Check your rifle when received for QC issues while in warranty. In the video I used pin punches (1,5mm / 2mm), rubber hammer, hammer, gunsmith bench block and file. Take care of your rifle and you will have a lot of fun! :>
@hubi143
Жыл бұрын
@@reff942 thanks for reply bro. bro i have suggestion. can you make a video on what to check for qc after unboxing the bnew ghk. it would help a lot of newbie people like me. like need to fix, etc.. or need to upgrade.. something like that,.. to tell you the truth i have no idea what to check or how its work's lol.
@JaeJaezX1
Жыл бұрын
Hello, I just wanted to ask if it's necessary to dismantle the entire magazine in order to file it? I'm assuming that you dismantle it so the spring and feeder dont' get in the way of filing? Just asking since I have 7 mags to go through haha.
@reff942
Жыл бұрын
Hi, if you don't dismantle it completely you can damage your gas route. But it can be done.
@JaeJaezX1
Жыл бұрын
@@reff942 thanks for the info! I'm running into quite a lot of trouble taking out the feedlip itself (cracked one, cut the rubber grommet on another). Is there another better way to take this damn thing out without completely breakign it? It doesn't come out flawlessly as yours did
@reff942
Жыл бұрын
@@JaeJaezX1 Try to gently tap it out with rubber/plastic hammer.
@jacobhernandez7366
2 ай бұрын
Good video, i have a question though. I have the golden eagle wa magazines for the mk18. However one of them leaks, i checked the valves and they dont look worn out or anything. Any tips on how to fix that. Also every time i shoot it doubles feeds or doesnt cycle correctly.
@reff942
2 ай бұрын
Remove mag shell and sink the mag into the water. That will show you exact leak spot. Double feed usually means broken or cracked lips. How is mag to nozzle seal? Does nozzle stick on the mag for a bit during cycle?
@jacobhernandez7366
2 ай бұрын
@@reff942 okay ill try that. and it looks like it doesn't stick on the mag, it cycles all the way through.
@gabecollins5585
9 ай бұрын
What is that tool you used that had the holes so you can push the pins out without hitting the table? Where can I get one?
@reff942
9 ай бұрын
Gunsmith bench block.
@gabecollins5585
9 ай бұрын
@@reff942 Thanks! Appreciate it.
@Tsukunami
Жыл бұрын
There a way to fix the Mag lever that lifts up the bolt catch when empty to catch the bolt? it doesn't go high enough or my mag won't go high enough to catch the bolt, the bolt cycles and goes home every time even on empty
@reff942
11 ай бұрын
You can gently bend bolt lock part down, so its pushed up sooner on empty. Remove part from the rifle to prevent damaging lower receiver berofe adjusting.
@Tsukunami
11 ай бұрын
@reff942 it's okay I eventually figured it out, I disassembled the mags and added material around the lever tab that activates the Bolt Catch when mags are on empty, so now they sit higher which is just high enough to push that Bolt Catch lever all the way up and Catch the Bolt everytime on empty. They're Golden Eagle MK18/PMAGs but they're nearly identical to the GHK Ones in terms of build.
@windynguyen1511
Жыл бұрын
question my gun ghk akm gbbr i have problems with two mag ak74 when i shooting about 6-7 bbs rolling out outer barrel i mean when shoot bbs have to rolling out and then normal shoot any bbs
@reff942
Жыл бұрын
Hi, do you have this issue with all mags, or only with two and the rest is fine? If only two are bad, your feed lips could be already broken and it cant handle the pressure from magazine spring. After releasing some bbs the pressure is lower and even broken lips can handle it. Check it, usually it is broken right in the middle.
@lukasbarinka_
Жыл бұрын
Prasknou stejně...cnc je cesta :)
@reff942
Жыл бұрын
Už ani nevím, kolik měsíců mám objednáno :D
@lukasbarinka_
Жыл бұрын
@@reff942 ja se dočkal po 7 měsících 😁
@bigbuna
Жыл бұрын
still cracking with this ?
@lukasbarinka_
Жыл бұрын
@@bigbuna Yes, sooner or later
@reff942
Жыл бұрын
@@bigbuna Running mags like this for a year now, no crack so far. But yes, it is still possible.
Пікірлер: 31