Thanks mate, I have a problem with my screen and i`m planning to buy a new one and replace by myself, it is good to have a video explaining what to expect...
@jrronimo
3 жыл бұрын
Thank you so much for this video! I'm working on an Aero 15 with a broken hinge and it was helpful to see that the whole display is glued together. Frustrating, but helpful, haha. Many thanks!
@micahedwards1188
Жыл бұрын
I've just broken the hinge on mine - not having much luck finding anyone with a replacement in stock 😐
@computerrepairplus
2 жыл бұрын
Great video, Thank you for uploading this video.
@jotatsu
3 жыл бұрын
For reference SD10Q66969 is compatible with the aero 15 oled, very expensive and hard to get on ebay.
@WillJackDo
4 жыл бұрын
Is it an oled panel?
@bobsagget823
4 жыл бұрын
I tried doing this like a year ago and gave up, I'm glad you figured it out even if this looks like a massacre cosmetically
@kjrhfnphil
4 жыл бұрын
it honestly wasnt that hard. just takes patience and being carefull.
@jeremyjohnsonMWN
Жыл бұрын
Well, that was easy. Thanks so much! I would have made this a lot more complicated... Got my screen off in just a minute or two. Thanks! Now I just need to find a new one.
@Alashrafi_
10 ай бұрын
did u put any tape on the backside of the panel? also how did u tape the rubber bezels?
@Lapaet
2 жыл бұрын
Hello ! Thanks for the video ! I have a question, did you use any extra glue or tape during the swap ?
@irnainhaider
Жыл бұрын
Hey man, I need a screen for my laptop because my existing screen start showing horizontal line due to faulty IC chip. So I am finding exact replacement for my Gigabyte 15.6 KD laptop. It's a OLED Panel. I can't find on the internet canyou send me exact link from where I can order ?
@CandleGuyFX
4 жыл бұрын
I thought the screen came with the rubber seal preinstall? I wanted to replace my screen but of that's how it is when I'll just let it be and never buy gigabyte again.
@kjrhfnphil
4 жыл бұрын
Ok.....? Thank for sharing.
@esmail88
Жыл бұрын
if you still have the bad screen around , what's the model of it or part number or any info to get the right screen. shipping cost is 53$ from US to outside country from the same website you mentioned in the video . searching with the laptop model didn't get that much of choices in another sites.
@jhonatancock2302
3 жыл бұрын
I hate they glued it, i have to check for a possible loose lcd cable in this model and it means risking losing an oled panel that you cannot buy.
@me85638251
4 жыл бұрын
Thank you!
@jmbqo
2 жыл бұрын
Seems to be the same setup for the Aorus 15P. Is it necessary to remove the screen for replacing the lcd cable? The hinges on the laptop broke the lcd cable, and that’s the only thing i need to replace. Thank you for the video Philip!
@mog3317
2 жыл бұрын
Same here, did you figure it out ?
@jmbqo
2 жыл бұрын
@@mog3317 I have not work on it yet, but it does seems like it would be necessary, as the LCD cable seems to be connected behind the LCD, for what I've been able to find. Gigabyte really sucks with their support, and their service manual information. Love the computer performance, but I don't think I would purchase their laptops again.
@Amr_Dabour
6 ай бұрын
@@jmbqo i alsio have aorus 15p .and my laptop screen is work for about 10s then go black but when i reduce refresh rate i works normally. is this aslo a cable problem ?
@jmbqo
6 ай бұрын
@@Amr_Dabour That sounds more like either driver issues, or an LCD panel issue. I would try to uninstall and re-install the video drivers first and see if that helps!
@zholud
Ай бұрын
Same here but for aero 14. Smaller cable (not the 40 pin one) broke because of the lid attachment clips and I need to replace it. Should I buy the whole cable? Is it one solid cable both 40 pin and 10 pin which presumably is damaged and is the one supplying the back lid?
@thedick31
4 жыл бұрын
Thanks for the video. I’m about to perform the same screen swap. It’s my first screen swap. How tough was it and any tips or tricks you could share? Thanks!
@kjrhfnphil
4 жыл бұрын
Hey! Make sure to use a hair dryer and really work on that bottom plate with the aero logo.
@thedick31
4 жыл бұрын
@@kjrhfnphil Thank you! What do you mean by really work on that bottom plate? Is there a side or place you should start from?
@kjrhfnphil
4 жыл бұрын
@@thedick31 no. What I meant is. Make sure to use the hair dryer on it for a while to fully soften the glue other wise you'll bend it like I did. There are only two things to remove. The rubber seal around the screen and the metal plate on the bottom. Then you just work around the corners with the tool and the hair dryer as you go.
@saikrishnapantangi9205
4 жыл бұрын
Can the pin count on the lcd
@kjrhfnphil
4 жыл бұрын
@@saikrishnapantangi9205 what....?
@shifureisaikyou2055
2 жыл бұрын
landscape mode
@kjrhfnphil
2 жыл бұрын
What…?
@user-yd6mo7og6f
3 жыл бұрын
Where to buy panel where is aero typed.I don't know how its called
Пікірлер: 41