the mono hull is trimmed way up to exaggerate... just sayin'
@Useitorloseit1
5 жыл бұрын
First thing I noticed too!
@spearfish25
5 жыл бұрын
So when do we see the 3-5' seas?
@markuswilmes3694
11 ай бұрын
Beautiful and that boat didn’t sneeze once
@PATH201
10 жыл бұрын
1'-3' Seas more like the truth!
@theamerican383
5 жыл бұрын
it is the truth. Majorsmackdown is correct though. The Fountain is way over trimmed to make it seem much worse than the reality of the sea state. Horrible advertising guy or gal.
@krkabob
5 жыл бұрын
And it kicks a mono hulls ass in any sea... you see it in the video:-)
@prohen3049
5 жыл бұрын
Boat must be running 20knts in 3-5in seas
@catchnbait
6 жыл бұрын
1-2ft, barely whitecaps and you can see the waves weren't even coming up on the front two hulls at all. Glaciers run thru the waves not over.. granted they will ride good but this is 1-2 ft at best
@krkabob
5 жыл бұрын
And the mono hull struggles big time....
@gypana
5 жыл бұрын
1-2 ft seas on a 2-3 ft swell.
@mikestevens2053
6 жыл бұрын
where are the 3-5' seas?
@CHASINGPROFITS
7 жыл бұрын
Do you have any more of these?
@darrynbutler922
6 жыл бұрын
nice
@markpitchford7375
10 жыл бұрын
Definitely smoother. What's the size of the mono running alongside?
@mocij77
7 жыл бұрын
i asked to factory. it was 25'
@steveross2280
7 жыл бұрын
It's a fountain most likely a 23' because of single engine, would put twins on a 25
@skullhart
8 жыл бұрын
Sneeze Sneeze Sneeze
@jamesmcclure3502
7 жыл бұрын
3-5ft😂😂
@henrye718
9 жыл бұрын
1-3... 1-2... both know nothing about boating waves are impossible to judge by a camera.. They are 3-5 can tell by the way the boat is handling. Mono hull is going air born, No way it would do that in 1-3s....
@b58forever
6 жыл бұрын
Catamaran too I don't need to be there to know there's no 5' waves. thanks
@Timbo_tango
3 жыл бұрын
You can clearly see the mono hull has its motor trimmed way too high on purpose to exaggerate the difference between the two boats.
@henrye718
3 жыл бұрын
@@Timbo_tango mono hull going to fast for it's length and the size and style of hull for those waves. I would have it trimmed up too trying to deal with those waves and not shake/slam the teeth out of my mouth. He was going airborne, This is obviously to much for that boats design. That's a bay boat not an offshore style boat.
@Timbo_tango
3 жыл бұрын
@@henrye718 Yes i would have trimmed up but i would have only used half of that boats trim. It was way too much.
@Eric-zs6rd
2 жыл бұрын
@@Timbo_tango Trim makes no difference at the point that the boat is going fully airborne between sets of waves. When the boat is airborne the landing spot is the landing spot, you can't cut all the waves with the bow.
Пікірлер: 29