Thanks for the awesome video. Yours is the quickest disassembly video I have ever seen on UTUBE. I have always been hesitant to disassemble the upper. It’s not as complicated as I previously thought. Thanks again and stay safe out there 🙏.
@punksnotdeaditsconservativ1693
Жыл бұрын
That makes two of us.
@nathanskupowski4726
Жыл бұрын
@@punksnotdeaditsconservativ1693that makes 3 of us
@user-ob3gi5do1i
16 күн бұрын
I'll repeat what everybody else has said--super clear and concise instructions. Thanks for sharing!
@duthegee
3 ай бұрын
A video from 3 years ago still helping out people. Thanks for taking your time to make this video!
@ghoste2055
2 ай бұрын
Thank you I just got a new nitride slide and this video made the assembly process so easy
@youngkreisler
8 ай бұрын
Thanks for the instructions! Worked like a charm!
@canyougetthat507
16 күн бұрын
Thanks man, I always come back to this 😂
@Frank-pf9iz
11 ай бұрын
Thank you this video was straight forward and I got my new slide on!
@punksnotdeaditsconservativ1693
Жыл бұрын
Thanks for the straight forward, to the point, informative video.
@dameonhunter2210
5 ай бұрын
Quick video very clear and to the point thanks man
@jaymiller338
2 жыл бұрын
Best video by far, I've seen to remove the slide backplate, so I can insert a custom plate.
@esty6983
3 ай бұрын
Thanks for the video. Solid set of paws on ya
@QUIET151311
2 жыл бұрын
Nice job explaining everything. Thank you.
@quigleypuffs
10 ай бұрын
You’re a scholar and a gentleman.
@viintage4689
7 ай бұрын
Fast simple to the point, thank you
@kaotick9719
Жыл бұрын
Hey loved the tutorial helped me fix my pistol and id love to thank you agian brother be safe and god bless
@matthewallen6875
Жыл бұрын
Appreciate the video. just got my new optics cut slide and this helped a lot
@didisaythat4230
Жыл бұрын
Very quick and detailed. You dont see videos like this very often anymore. Im having exteacting issues on my p80... how likely is the exteactor to be the issue? Im aware of the one part that people often times swap out. Im just wondering if the extractor could possibly be the issue. It just doesnt seem to kick the shells out.
@AKjose47
Жыл бұрын
I’ll say this: if you have a optic cut slide, your problem very well might be that the optic cover screw or optic screw on the extractor side is probably too long and interfering with the extractor rod. You’ll know if this is the case by trying to remove the extractor rod and if does not come out freely then there is interference there from the screw. If it comes out freely then of course make sure it is installed in the correct orientation, spring and bearing should be towards the back of the slide and rod should be up front against the actual extractor. If that’s good then the extractor itself could be the issue.
@michaelwells7311
5 ай бұрын
Great video
@leodoro8877
Ай бұрын
thanks
@nelsonh.568
4 ай бұрын
That was a great video bro, I appreciate simple and correct!
@shrmp5451
Жыл бұрын
One of my springs and plunger went flying and I didn't where it went
@jayman3573
8 ай бұрын
No cleaning oil or anything needed?
@AKjose47
2 ай бұрын
This was just a take down and reassembling but for cleaning I would use a cleaning solvent and soak for a bit then clean it off with a clean cloth or rag. You can use a dental pick or similar tool to scrape off any carbon build up if needed. Then use very light oil like CLP or any gun oil and use a little on the springs. Very little. And oil, not grease. The recoil spring is the only spring I would even consider using a lithium grease on. But I still prefer oil for that as well.
@victordiblasio3019
2 жыл бұрын
Can you do a Glock 19 (preferably gen3) lower frame assembly ?
@AKjose47
Жыл бұрын
Coming right up
@WN8HGZ
2 жыл бұрын
Very good should those parts be lubricated before putting them back in to the pistol
@AKjose47
Жыл бұрын
On the slide I only lubricate the guide rod/recoil spring and the rails that ride on the frame.
@yxngfolks223
2 ай бұрын
My spring keep falling how do I fix that ?
@AKjose47
2 ай бұрын
@@yxngfolks223 which spring? I’m guessing the trigger safety plunger spring. I would put the spring on the safety plunger then hold the slide, sights side up, and put plunger and spring in from the bottom up so the spring doesn’t fall. Once it’s in, make sure it is in there and not binding up. Once the extractor is in the plunger will stay in place.
@MrBeachDoctor
Жыл бұрын
great vid, thanks
@jasedelgadillo9137
Жыл бұрын
Is this gen3 or the same as the gen3?
@AKjose47
Жыл бұрын
This is a gen 3 but they are all the same pretty much.
@jasedelgadillo9137
Жыл бұрын
@@AKjose47 thanks man I was able to change out my upk to my new slide no problem thanks to this video👌🏽
@JBBombster
Ай бұрын
dudes got safe and sound blaring
@K1ngDre-DMZ
Жыл бұрын
Dude you rock! Thank you!!
@warningshot910
3 ай бұрын
Wait, this aint airsoft
@ghostblack9209
2 ай бұрын
Big meaty claws lmao
@doulatram5919
2 жыл бұрын
Exlent 👍
@ItchyPilauBoto
2 жыл бұрын
I hear Tribal Seeds, your arms are super hairy lol but thanks for the video bro.
@AKjose47
2 жыл бұрын
Lol thanks for that?
@masteryoda3558
5 ай бұрын
Isn’t that roller skates by steel pulse?
@DavidLLambertmobile
Жыл бұрын
The music, noise in the background is a distraction. ⬇️
@battleborn2002
2 жыл бұрын
POORLY DONE!
@AKjose47
2 жыл бұрын
I made this video for a customer that ordered a slide and was scared to disassemble his oem slide to instal the parts I to the new slide. Sorry to disappoint you lol. Maybe you can make a better video and finally upload something to KZitem after 14 years?
@BobbiSkankanos
Жыл бұрын
half the video is over before this genius gets the backplate off! then on reassembly, reinstalling the extractor, he says "round part goes to the back" except he shows no round pat and there is no "rtound part on the back of the extractor!
Пікірлер: 51