I’m saving this to refer to later when I need to do a deep clean. Thanks for taking the time and effort to show us how it’s done.
@KimandGarrettmakeit
3 жыл бұрын
Glad it was helpful!
@susanjohnson3376
2 жыл бұрын
Thank you for such a detailed video. So many have shown taking a screw out to remove the belt and air assist fan and I was way to scared to do that. So helpful!
@KimandGarrettmakeit
2 жыл бұрын
Yes! so glad we could help
@CVSPOTLITE
3 жыл бұрын
I’ve done a surface clean but was scared of doing a deep clean. I was afraid of damaging something. Thank you. This helps a lot! 👍
@KimandGarrettmakeit
3 жыл бұрын
Glad I could help!
@petelozzi7298
Жыл бұрын
Nice job those camera angles behind there were really helpful
@MsTaylor0304
3 жыл бұрын
I am terrified of taking everything apart
@KimandGarrettmakeit
3 жыл бұрын
Take picture! It. Helps
@adaur981
3 жыл бұрын
There are instructions on how to properly remove the belt. The right wheel is to be loosened by using a 3mm hex key about a quarter turn The wheel can then shift to the left, releasing the belt tension.
@KimandGarrettmakeit
3 жыл бұрын
THANKS for the info!
@Walsfeo
3 жыл бұрын
I've heard it's tough to get it back in place. Has that been an issue?
@adaur981
3 жыл бұрын
@@Walsfeo no, wasn't a problem at all.
@mikecapers832
3 жыл бұрын
The best comment on youtube ever.
@bettyfred5439
3 жыл бұрын
Holy heck you just just my life and my fingers! That was SO much easier!!
@amandapowell7184
Жыл бұрын
Thank you Garrett. I got an error only my error assist fan the other day. Watched your video to get it clean. Super helpful video!
@KimandGarrettmakeit
Жыл бұрын
I'm glad it helped. Thanks, Molly!
@kelleysral4504
7 ай бұрын
It seems easy enough. Thanks for the demo. I am so afraid to do it, but it needs to be done.
@timokayz
Жыл бұрын
Outstanding step by step. Very helpful.
@samanthamielbrecht2759
3 жыл бұрын
Thanks so much for this video! I’ve been needing to do a deep clean and it helps to SEE the process. You guys are great. Love your channel. 👍🏻
@reneebanbury7066
3 жыл бұрын
You are good man to do all of that cleaning! So proud of you!
@KimandGarrettmakeit
3 жыл бұрын
Thank you! It's his baby
@tinamickelson9459
3 жыл бұрын
I REALLY want a she shed and a glowforge. I feel less intimidated now that you showed how to clean it.
@KimandGarrettmakeit
3 жыл бұрын
Yes! it's not too tough at all!
@karismaolson
3 жыл бұрын
Thank you!! You've made this soooo much less scary and intimidating to me. :)
@riki-leedicarlo2900
2 жыл бұрын
Great video! How do you get to the fan maintenance screen?
@kellieodman3366
Жыл бұрын
Where do I go to turn fan on to clean, as you are showing in this video?
@atlas7680
Жыл бұрын
This is why I'm glad I own a Universal laser lol. This seems like a hassle to clean compared a uni.
@KimandGarrettmakeit
Жыл бұрын
YES! Our bigger lasers are easier to clean and less often.
@KimandGarrettmakeit
Жыл бұрын
YES! Our bigger lasers are easier to clean and less often.
@jareyano
Жыл бұрын
@@KimandGarrettmakeit What lasers would you recommend as I am looking to step up from my 2 Glowforge
@ximelrs2235
4 ай бұрын
I can’t reattach the belt 😮 I’m going crazy. Any tips on how to reattach it?
@staindoiram
3 жыл бұрын
I honestly needed this video
@KimandGarrettmakeit
3 жыл бұрын
SO glad we could help
@joeep46
3 жыл бұрын
That's a save for me too. Thanks man. Love you guy say hi to the wife.
@joeep46
3 жыл бұрын
Hey Garrett can you guys do a video on all your shop tool
@1991ncr
7 ай бұрын
I want to clean it but I’m scared I will damage something.
@Walsfeo
3 жыл бұрын
Thanks for the video. I don't remember that fan cleaning interface, how old is that? We removed our built in fan and replaced it with an inline fan. It never gets as loud as it used to, and pulls a lot more air.
@KimandGarrettmakeit
3 жыл бұрын
Not sure We just got our forge last year
@jayneanderson4158
2 жыл бұрын
Great video, Thanks!!! I still feel the surfaces feel sticky after cleaning and the belt with laser does not move smoothly. Any ideas??? I don't want to damage.
@KimandGarrettmakeit
2 жыл бұрын
Thanks for sharing!
@mynewidtommy
3 жыл бұрын
Well done!
@KimandGarrettmakeit
2 жыл бұрын
Thanks!
@ashleyhamsher1065
3 жыл бұрын
Get the ac inline fan from Amazon if you don't already have one. It makes it soo much more quite when running! I love mine!
@KimandGarrettmakeit
3 жыл бұрын
We really want to get one!
@ashleyhamsher1065
3 жыл бұрын
@@KimandGarrettmakeit definitely should if you can. I got the ac infinity cloudline s6. Also got an attachment so it would fit the 4"inch exhaust tube on the glowforge and the 6" fan opening.
@jessicakeen2018
2 жыл бұрын
Doesn't a inline fan void the warranty? Just curious. I'm making sure I don't do anything to void the warranty. But if it doesn't I'm sure it's a life saver!
@ashleyhamsher1065
2 жыл бұрын
@@jessicakeen2018 no it doesn't. Lots of people get them because it's way more quiet
@liwhite484
3 жыл бұрын
Thank you...Thank you...Thank you! ❤️
@KimandGarrettmakeit
3 жыл бұрын
You are so welcome!
@tylhereasterbrook4452
2 жыл бұрын
Thanks!
@KimandGarrettmakeit
2 жыл бұрын
Thanks!
@brendanurre1517
Жыл бұрын
I can't get band to go back on the left side! Please Help
@KimandGarrettmakeit
Жыл бұрын
Ah! I had this problem! Is your ribbon plugged in upside down? That was my issue.
@brendanurre1517
Жыл бұрын
@@KimandGarrettmakeit Got it. Also, Thank you for showing an actual dirty GF. Everyone else's videos are them cleaning a clean GF.
@jeankohtala666
Жыл бұрын
My crumb tray gets so gunky from the MDF. How do you clean that…or do you?
@brandysigman4203
2 жыл бұрын
Excuse my crazy question. Is the QD contact cleaner a degreaser you are using instead of the 3M?
@KimandGarrettmakeit
2 жыл бұрын
It's just a big box from amazon www.amazon.com/shop/kimandgarrettmakeit
@jav9888
3 жыл бұрын
Thanks for the Vid, do you by chance clean the lights on the lid ? and if so what did you do and use ? thanks in advance.
@KimandGarrettmakeit
3 жыл бұрын
I'm not sure what you mean!
@jav9888
3 жыл бұрын
@@KimandGarrettmakeit Sorry the LED lights along the sides of the Lid mine are is all yellowed out.
@KimandGarrettmakeit
3 жыл бұрын
Ah! We just used the magic eraser on those as well.
@lynnreynolds905
2 жыл бұрын
I clean my machine every morning and use a soft paint brush on the lights (vinegar water and Windex) and wipe it down with a soft microfiber cloth when done.
@KatieDevlin
3 жыл бұрын
How long did this take in real time?
@KimandGarrettmakeit
3 жыл бұрын
It took about 2 hours, but I had to move lights and cameras. I think I could do it again in just over an hour. Cleaning the exhaust and the air assist fans were the longest part. I cleaned each one for about 20 minutes.
@KatieDevlin
3 жыл бұрын
@@KimandGarrettmakeit thanks!
@theresagross3523
3 жыл бұрын
@@KimandGarrettmakeit , Thank you, so much for this detailed video. I am going to be getting mine soon and this will definitely come in handy. How, can we use your coupon code for the $500 off? Also, can you make a video on where you get your svg’s from and how you do the layering cuts for things that require layers. Again, Thank You so much! You guys rock! Tell Kim we missed her in this video😊.
@mauiwolf618
2 жыл бұрын
Have you had any issues with your Glowforge? I am having tons.
@MissSadara
3 жыл бұрын
Time to get it dirty again! 🤪
@KimandGarrettmakeit
3 жыл бұрын
YES absolutely
@cmurray666
3 жыл бұрын
What handheld vacuum did you use?
@KimandGarrettmakeit
3 жыл бұрын
just our low power shop vac
@lynnreynolds905
2 жыл бұрын
I hope I never let my GF get that filthy. I wipe my GF down every day prior to using it. It helps keep up with the dirt and grime you are cleaning off of your machine.
@KimandGarrettmakeit
2 жыл бұрын
That's a great way! We use our glowforge like 3 times a day and our daughter uses it to make jewelry so ours is WELL LOVED
Пікірлер: 77