The first youtube chanell to use a diesel engine as a intro
@th3s3rv37
4 жыл бұрын
Find it funny. The T piece for boost gauge. Only one hose clamp for the now 3 lines. Should be 3 really.
@ronnieboucherthecrystalcraftsm
Жыл бұрын
a tight cable tie will do !
@ivervj2923
Жыл бұрын
Question: Putting that T fitting doesn't reduce the boost since now there is a deviation for the gauge reading?
@Tea18236
Жыл бұрын
it would if you tapped into waste gate actuator line. but if you tap into blow off valve like in the vid it wont.@@ivervj2923
@raynd5769
11 ай бұрын
@@ivervj2923nope won’t affect anything
@ronnieboucherthecrystalcraftsm
Жыл бұрын
i do not recommend removing exhaust heat shields = = so much more under bonnet heat ! = even fit a turbo blanket and your subaru will love you ! = all these gauges great idea and often needed ! = GO SUBARU - more smiles per miles !
@averysuarez2622
2 жыл бұрын
Don’t tap in to the clock/passenger air bag indicator wiring on 2006/2007 models. and be sure to leave that clock/air bag indicator plugged in and tucked away or You WILL get an airbag light.
@amauryjay4
Жыл бұрын
New to Subies, I have 06' WRX. So youre saying dont use the wires for the clock in the center?
@23hublock1
3 жыл бұрын
The shroud could be a lot better, needs to match the dash, plus clip in the same places where the clock came out. I have a PSI 3 reader on my dash, plug and play into the OBD....but doesn't have oil temp or pressure readings, I'd need work done to facilitate that.
@Owensti
Жыл бұрын
You could flock the entire dash including the bezel piece so everything matches. But trying to match material from a 15+ year car isn’t going to be the easiest thing. It’s always going to look either off or newer.
@zanemoeller1931
4 жыл бұрын
Whyd he have to use half the roll of Teflon on one thread of the t fitting lol
@djinsainedboyeditz
5 жыл бұрын
i love it
@popanollie1
4 жыл бұрын
10:44 how did the screws on the back of the gauge grow like that
@GlowShift
4 жыл бұрын
Your gauge should have come with extensions that screw onto the back of the gauge.
@Chippyd363
2 жыл бұрын
SUUUUBIEEE!!💪💙💯
@anjandas8461
2 жыл бұрын
Boost pressure gauge needle not swip up when ignition on
@hustleperformance9004
2 жыл бұрын
In my 04 wrx i keep blowing my fuse has anyone had to use a bigger fuse for it to stop blowing? Fuse in question is the radio fuse its a 15
@GlowShift
2 жыл бұрын
The 15 should be fine. Double check all the wiring to make sure it is all secured and there are no shorts.
@abdullahnahas3728
8 ай бұрын
Does anyone have a link to the red female terminal connector, can’t seem to find them anywhere
@zacharysforcina3569
6 ай бұрын
Did you find them by chance?
@kong951
4 ай бұрын
Autozone
@adran_va2
Жыл бұрын
installed the kit w boost, oil pressure and temp, and now my ambient temp is reading 122° and the oil press and temp are maxed on gauges on start
@GlowShift
Жыл бұрын
Can you verify which gauge series your gauges are? Double check that the temp sensors are connected to the correct gauges. Our gauges tend to max out when the wrong sensor is attached.
@kelvinzaldana2943
3 жыл бұрын
And how much was all that I mean how much do you charge? I wanna do it to my 02 WRX IMPREZA
@GlowShift
3 жыл бұрын
We do not do customer installations but the price of the gauge packages will vary depending on which gauges and pod you choose. Click the link in the description and it will take you to the page where you can configure your package.
@silverrex81sandy21
4 жыл бұрын
Where can I get some of those nice over the wire crimp on fittings.
@alexisfernandez6797
2 жыл бұрын
Can I install the oil pressure gauge without using a sandwich adapter?
@GlowShift
2 жыл бұрын
Yes, as long as you have a port on the engine that will show oil pressure.
@jonney8046
2 жыл бұрын
Sandwich adapters introduce another point of failure to the mix, so I would avoid those if I were you. The best place is the port underneath the alternator. That is where the OEM one is, which is just above the oil pump. Swap out the OEM one with your gauge sensor and your golden. The engineers put it there for a reason.
@iElementGraphics
4 жыл бұрын
I did this exactly how in the video and the clock harness cant handle enough amperage to power the gauges and the fuse blows, why design your instructions around a method that doesnt even work?
@GlowShift
4 жыл бұрын
Double check your wiring to make sure you do not have a short somewhere. Also verify that the correct amp fuse is being used. Using the clock harness should not be blowing the fuse.
@iElementGraphics
4 жыл бұрын
@@GlowShift The fuse being used is a 15 amp which is what is used in the wiring diagram on the back of the cover, its wired up properly because for the first 15 minutes everything worked flawlessly like it should. I'm wiring it up to the fuses behind the coin tray instead with add a fuses circuits.
@1MotoXRacer1
4 жыл бұрын
These don't even draw close to enough power for the little LED's. Hell your stock clock should be pulling more amperage than these 3 gauges with that normal light bulb. You had a short there, buddy. Always triple check.
Damn that’s like 40 feet of boost line. Some gauges only need 12 inches of hose
@ihtiyardelikanl9217
3 жыл бұрын
it's too complex for me
@BateMasterJeff9887
2 жыл бұрын
Man this too confusing. Hell naw I’m out
@averysuarez2622
2 жыл бұрын
Don’t tap in to the clock/passenger air bag indicator wiring on 2006/2007 models and be sure to leave that clock/air bag indicator plugged in and tucked away or You WILL get an airbag light/malfunction
Пікірлер: 48