Do i have to program a Tcm even if i get a used one out of the same car (junkyard)??
@mistersaoco
2 жыл бұрын
Where can i find a tool to program any brand of cars? I would like to program a mazda 6 2008
@eulalionunez9691
4 ай бұрын
I have an 08 enclave. I replaced the tcm. How much would I have to pay to get it reprogrammed?
@DionisisTsiapalis
3 ай бұрын
Hello friend! From your experience do you think I can replace a 6T40 Gen1 from my Opel Astra J with a new one transmission 6T40 Gen2 and programming the new TCM(clear TCM) for my car without any problems at the synchronization with the ECU of my car? Thanks! (The same car with the same engine code after 2012 equipped with a Gen2 6T40)
@carlossilva261
3 жыл бұрын
I have an 2015 impala Ls l4 , my car is currently at the mechanic shop , whenever they put a used transmission in , do I have to take it to the dealership to get it reprogrammed? Or no because the used transmission they’re putting in is stock and it matches with my vin #
@huyug1
3 жыл бұрын
Hello, if the vin matches you shouldn’t have any problems. Sorry for late reply
@ds6843
2 жыл бұрын
@@huyug1 what if it's a different transmission from another Impala.
@huyug1
2 жыл бұрын
@@ds6843 I have see many cases that used transmission doesn’t have to be programmed. Check for DTC after replacing unit. Refurbished and new ones needs to be programmed.
@jaijohnson9666
7 ай бұрын
I replaced my tcm but need to reset the system. How can i do it?
@LH-zn3jg
Жыл бұрын
I replaced shift and pressure control solenoids in a 2006 Buick rendezvous to address a dtc and the lack of gears d, 3, and 2. Do I need to have the transmission programmed?
@keyz4prez237
Жыл бұрын
Did you have to program it
@jonathanarreguin3826
5 ай бұрын
Can I do this with a mongoose plus gm3?
@cousinvinny7990
4 жыл бұрын
would this be the same procedure for a gm vauxhall insignia tcm replacement?
@huyug1
3 жыл бұрын
I’m sorry for the late reply since I just saw it. Yes! All GM transmissions almost programmed this way.
@cousinvinny7990
3 жыл бұрын
@@huyug1 Thanks for your reply i got mine done finally last week that said because the psa group in europe have taken the opel / vauxhall brand the ac delco site is not for my car they were very helpful in finding the psa site for sps programming it is the same procedure
@paulinesgobin4793
3 жыл бұрын
Thank you !
@blacisuzu1471
2 жыл бұрын
I have 2009 Cadillac escalade. The tran is reading. P2723 it wont move unless gas is applied. Do i need a new tran or what
@huyug1
2 жыл бұрын
The car needs to be diagnosed properly with a professional diagnostician
@fadik2084
3 жыл бұрын
Have chevy cruze 2009 automatic transmission when the car reach 5 it act like it downshift after reprogramming the car it act normal for 6 hours and then return to same problem what do you think my problem
@huyug1
3 жыл бұрын
It sounds like you have transmission module problem or transmission itself. Do you have any stored codes?
@fadik2084
3 жыл бұрын
Huseyin Uyug thank you for reply there is no transmission code only o2 sensor and thermostat code
@taimurkhan7493
3 жыл бұрын
Which Software are you using for the programming in Laptop?
@huyug1
3 жыл бұрын
It’s called SPS ( service programming system) which for gm Vehicles
@cedthetruth1311
3 жыл бұрын
@@huyug1 Hi, I have a 2009 Impala 5.3 I just replaced the transmission and now I have no start issue.Does TCM have to be programmed to this new transmission? Also I have no communication from the trans to the ECM and no shift box icon on the on the instrument cluster.
@huyug1
3 жыл бұрын
@@cedthetruth1311 -if you have put in used transmission no really need to program but if new transmission yes definitely needs to be programmed. -if you cant basically can’t communicate with Tcm; it can be for many reasons such as No 12 volts to tcm No ground to tcm Can bus issues Bad transmission
@huyug1
3 жыл бұрын
@@cedthetruth1311 I had same issue actually with same exact vehicle and it was the transmission. I’m not saying that’s your case but be careful with rebuilt transmissions with GM vehicles
@hardtimefarms9270
3 жыл бұрын
Put a upgraded tranny in a 06 lbz with Allison 1000 6 speed had a man relearn the tranny but it wouldn't let him do a relearn any ideas why
@huyug1
3 жыл бұрын
Did you replace the control module of TCM?
@alonzojohnson7563
Жыл бұрын
Good content
@checkmate4213
2 жыл бұрын
Hi, I’m trying to fix a flooded car I’ve already replaced the engine & transmission. Now I’m on all the electrical components if I buy all the modules can I use this software to program all the modules to my vin? The dealership is charging me a arm and a leg
@huyug1
2 жыл бұрын
Definitely! You can program used and new modules as long as you a decent laptop and and a j2534 device. This software is SPS1 which outdated and shutdown. I have another video with SPS2 which is the new system.
@checkmate4213
2 жыл бұрын
@@huyug1 I have a jeep, would I use this same software your using? Or a different one?
@huyug1
2 жыл бұрын
@@checkmate4213 no, another software called wiTech which is only for FCA vehicles.
@checkmate4213
2 жыл бұрын
@@huyug1 ok thank you man!
@gerardovinalay2152
3 жыл бұрын
Ok well can you reprogram any tcm i have a gmc acadia 07 but i read a lot of info on the net about putting a 2010 transmission but it said swap the tcm for no program needed can you clear this out for me
@huyug1
3 жыл бұрын
Yes, if you swap it with the Tcm you won’t need programming BUT if there is a sequence programming with the ECM then yes you still need to program it
@huyug1
3 жыл бұрын
Basically the ecm and the tcm need to learn each other in some cases
@emmanuelopoku-agyemang3299
3 жыл бұрын
I have chevy cruze (Daewoo Lacceti) 2010 model from South Korea, I had issues with the automatic transmission for some time and I decided to convert it to manual transmission. The conversion has been done but my auto electrician is not able to start the engine for me. We have consulted other auto electrician available but it seems they are clueless. The diagnostic machine detects there is break in communication with the TCM. Any help?
@huyug1
3 жыл бұрын
If the TCM located in valve body you would have to also replace the ECM as well or need to be reprogrammed to work with the manual transmission if t still doesn’t work check all wirings or short and use a scope to detect communication status tcm.
@emmanuelopoku-agyemang3299
3 жыл бұрын
@@huyug1 Please I will like to engage you further. This is my whatsap number +233560467391 or email: eopokuagyemang@gmail.com. Thank you
@huyug1
3 жыл бұрын
@@emmanuelopoku-agyemang3299 no problem I will give you a call in couple hours.
@emmanuelopoku-agyemang3299
3 жыл бұрын
@@huyug1 I will be waiting for your call then. Thanks a lot.
@emmanuelopoku-agyemang3299
3 жыл бұрын
Please I am still waiting for your call or whatsap message.
@turbo3089
3 жыл бұрын
Ok my 2003 dodge dokata doesn't want to shift past 3rd unless I force the car to go to 30 once it goes to 31-35 at on average 5k rpms it shifts just like normal from there is that a bad tcm bc it's not throwing any codes and it doesn't make any funny noises so please help
@huyug1
3 жыл бұрын
I’m also working on a ram 1500 with same issue will keep you posted once I solve the issue
@huyug1
3 жыл бұрын
Did you change tires at any point?
@requiem2803
2 жыл бұрын
Hii Code U0101 chevy malibu 2011 3.6l, is that code means its need to reprogramm?
@huyug1
2 жыл бұрын
No, it means you have no communication with TCM. Powers and grounds needs to be checked properly. Communication lines need to be checked with a lab scope. If everything looks normal, the TCM needs to be replaced
@emersonurbina8042
2 жыл бұрын
Can you make a link to download the version of the software you have
@huyug1
2 жыл бұрын
This software is no more in use. Now it’s SPS2. acdelcotds.com
@clutchin7017
3 жыл бұрын
How do I access the sps I don’t get the same screen as you
@huyug1
3 жыл бұрын
You need to go to www.acdelcotds.com Purchase programming subscription Click add vin You will see the same page as in the beginning of the video
@thenewmix9737
3 жыл бұрын
Hey there I have a Chevy Cruze 2011 LT and they told me that the transmission computer module has to be replace and I was wondering if u could install and reprogram the computer
@huyug1
3 жыл бұрын
Yes I can
@thenewmix9737
3 жыл бұрын
@@huyug1 where are u located
@huyug1
3 жыл бұрын
@@thenewmix9737 NYC area
@thenewmix9737
3 жыл бұрын
@@huyug1 oh okay I’m in Pensilvania so you’re like 2 hours away from where I live
@huyug1
3 жыл бұрын
@@thenewmix9737 if you have j2534 device and a laptop I can connect to your laptop and do it remotely. Or I can come to do it but I would have to charge extra. For further questions you email me at huseyin0240@gmail.com
@tafacildemais572
3 жыл бұрын
hello can you show us yours maxiim the you are using to do this job
@huyug1
3 жыл бұрын
I only used im608 for scanning codes which most regular scanners can do.
@squirrelysquirrely5388
Жыл бұрын
Would the car start before the program
@DocHolliday1110
2 ай бұрын
Did you get to start?
@waqasazmat81
3 жыл бұрын
Uyug I have couple of questions for you, what is the best way to reach you at?
@huyug1
3 жыл бұрын
You can give me a call at 1 (347) 265-0322
@chapasebastiano8
3 жыл бұрын
Hello Huseyin, I have a 2014 6 speed 5.3l ltz 2wd chevy silverado and I'm under impression that the tcm is also inside the transmission itself. Is there anyway to replace the tcm itself? I called orielly and autozone and they say they have the part available but no one knows exactly where it is located. How do I access this tcm any ideas? Do I need to take it to a programmer instead? I appreciate your time with this.
@waqasazmat81
3 жыл бұрын
@@huyug1 omg I didn't get any notification from KZitem that you replied. I will call/text you thanks!
@huyug1
3 жыл бұрын
@@chapasebastiano8 hello. It is together with the valve body inside of transmission
@chapasebastiano8
3 жыл бұрын
@@huyug1 thank you for quick reply. You are right I looked up part on autorock and module is big component part goes inside transmission. Now my debate is if I should buy a new transmission which I assume comes with the new tcm included inside or just buy a new tcm module and repair/replace old transmission with this new part. Any suggestions? You are a great help. Thank you
@ruthduran8307
2 жыл бұрын
How much does it cost to reprogram the transmission
@nikolaporte4370
2 жыл бұрын
Chevy dealer charged me $311
@Junaidngp
3 жыл бұрын
Hi, I am from India.. I would like to learn ecm and BCM car programing.. could you please help to learn this ...
@huyug1
3 жыл бұрын
Hi, I definitely can but this won’t be over KZitem. You can contact me on my WhatsApp at +1(347)2650322
@Junaidngp
3 жыл бұрын
@@huyug1 Thank you.
@TheBeast-tj9qo
2 ай бұрын
You can clone also..
@lordiraqe1631
3 жыл бұрын
سلام عليكم اخي ممكن سؤال
@huyug1
3 жыл бұрын
Sorry my friend I don’t speak Arabic
@symentressstringer8294
3 жыл бұрын
I just got my transmission replaced in a 2012 Chevy Cruze and I got the call yesterday that my transmission is not programming to my car but the man did not bring the computer so now it’s going to get ship to the dealership to see if they could program it I’m nervous
Пікірлер: 90