thanks for the tips. The firmware update was driving me mad! No where in the firmware instructions does it tellyou to go into the trigger menu and press the update icon!!!
@TossSong
13 күн бұрын
Thank you for comment. I’m this helped. I agree. The instructions was unbelievably tough to follow when I first tried to read it. I ended up having to experiment with it which I shouldn’t have to.
@aerialphoto
22 күн бұрын
not able anymore on mac. even when allowing in security settings it still does not allow to operate
@TossSong
22 күн бұрын
Thanks for reaching out. If you can, try again. Because I have been able to override the same firmware on my Mac, recently. You could try to contact Godox.
@fotostudioar6002
4 ай бұрын
I tried with Mac last version and Windows and nothing it doesn't turn on anymore if I press the little wheel with USB the arrow appears. The message from G3 says it has been run but it won't turn on
@TossSong
4 ай бұрын
Thanks for reaching out. Press the knob to see the arrow. Then plug it back in and select Update on the software until the green progression bar start moving. You may have to repeat again, press the knob, and select Update on the software until the bar moves. Let me know.
@nycks1
4 ай бұрын
Unfortunately I bricked my trigger trying to update it
@TossSong
4 ай бұрын
Hi, if you press and hold the knob and you see the arrow, it’s not bricked. Plug in back in and use the software and press Update until the green bar moves.
@nycks1
4 ай бұрын
@@TossSong Thank you
@TossSong
4 ай бұрын
No problem. Thank you for reaching out.
@SteveGong
4 ай бұрын
@@TossSong thanks so much, I thought I bricked mine too.
@TossSong
4 ай бұрын
No problem, I’m glad you got it going again. Thank you for reaching out.
@philwebbphotography3630
4 ай бұрын
Great video thank you so much!!!
@TossSong
4 ай бұрын
Thank you for your comment. Happy this helped.
@MathiasLundin
2 ай бұрын
Thank you!
@TossSong
2 ай бұрын
Thank you for your comment. Happy this was helpful.
@wortiz33
Ай бұрын
Every time I have a connected, it keeps disconnecting on its own
@TossSong
Ай бұрын
Thanks for reaching out. I believe almost everyone will get that disconnect message. It’s the app/launcher issue. I recommend keep trying based on my videos and/or reboot the computer and start again.
@TossSong
Ай бұрын
Also make sure you have the current launcher for your computer OS “Godox G3 Launcher V1.1”.
@colfotografoslucas2700
3 ай бұрын
En caso de que no esté claro... GODOX X3 TIGGER 1 Abra el godox programa G3 y cargue el version firmware 2 conecte el cable según el producto al godox x3. Tenga en cuenta que está apagado 3 mantenga presionado el botón de control giratorio durante unos segundos hasta que aparezca la palabra actualización en idioma chino en el Godox X3. presiona Ir para actualizar en tu computadora, espera 15 segundos 4 Cuando la barra de progreso en verde se detenga y la ventana muy difícil de leer que está sobre ella indique que la actualización se completó, haz clic en "Salir" Finalmente y listo. Desenchufe el cable ok
@TossSong
3 ай бұрын
Thank you for commenting and sharing.
@andif8
4 ай бұрын
YES, there was the problem: the manual tells to start the update via firmware updater app and didn't tell to first press update on the X3.
@TossSong
4 ай бұрын
Hi, thanks for reaching out. Did you get it resolved? Even if you did it out of order, you could still update it. If you haven’t, press the knob to see the arrow. Then plug it back in and select Update on the software until the green progression bar start moving. You may have to repeat again, press the knob, and select Update on the software until the bar moves. Let me know.
@andif8
4 ай бұрын
@@TossSong Yes, Thank you - it worked :-)
@TossSong
4 ай бұрын
I’m glad everything went well.
@wortiz33
Ай бұрын
I keep getting update device error
@TossSong
Ай бұрын
I also get that almost with every firmware update I’ve done. Keep trying to update it and see. Exit out if necessary. Reboot the computer. Turn off and on the trigger. Then try again.
@TossSong
Ай бұрын
Also make sure you have the current launcher for your computer OS “Godox G3 Launcher V1.1”.
@khoaitaysaudoi
4 ай бұрын
tks for sharing , idk why my x3 sometime it work sometine dont
@TossSong
4 ай бұрын
Hi, thanks for reaching out. Did you update the firmware? Or was it not working properly before also?
@khoaitaysaudoi
4 ай бұрын
@@TossSong yup i was update today , when to see your vid , before ver is 1.06 of sony , now it 1.09 but i dont have time to try
@TossSong
4 ай бұрын
I see. Hopefully it fixed the issues you’ve had with it. Let me know how it goes.
@khoaitaysaudoi
4 ай бұрын
@@TossSong yeh . I will . Thank you so much
@downsevilla
26 күн бұрын
@@khoaitaysaudoi Hi! You fixed after updating?
@juangraciavideo
2 ай бұрын
don't exist G· Launcher V1.1 MAC!!!!
@TossSong
2 ай бұрын
Hi, thanks for reaching out. I contacted Godox, they found a problem with the macOS Launcher and took it down. They’re working on it and should be back up soon. Here’s their reply: “Thanks for your email and sorry to hear the issue had to you. We're sorry that G3 Launcher V1.1 for Mac OS was currently taken down as our technicians detected a problem and are rectifying it. We apologize for any inconvenience caused.”l
Пікірлер: 49