I just replaced my OEM flasher with an LED Flasher for my Pathfinder Flashing Rear Brake Light and Turn Signals. I could not have done this successfully if it wasn't for your video Chris!!! The OEM flasher is a bugger to get to and to remove, but thanks to your video I was able to watch step-by-step and get it done! You do have to be a magician to change this thing out, but it's totally worth it to have the LEDs instead of the incandescent bulbs!!! Thanks Chris!!!
@da72ma
3 жыл бұрын
Biggest update is in the toolbox... with the JPS screwdriver set for the Japanese Phillips screws... you shouldn't be stripping any of them Phillips screws anymore, unless they are super stuck and super old... great video but unless I am doing the air filter I would attempt to change the flasher from the nose... it appears quicker and the lower windshield, which accumulated some dirt can be cleaned too... I like Electrical Connections but I got the Pathfinder kit from Socal Motogear... Oh and the best install video from you was the Electrical Connections bluetooth device... that really was a huge update with big thumbs up for Electrical Connections products for the Wing... Thanks Chris
@robdonell9915
10 ай бұрын
Hi, is it there more finger room to remove the turn signal relay by removing the windshield assembly ?
@da72ma
10 ай бұрын
@@robdonell9915 I took it all off but it took me awhile.
@jgreenfi330
4 жыл бұрын
If I could buy you a drink for posting this I would! This saved me a LOT of headaches with the flasher relay install. I was dreading tearing into my Wing just to get to that relay but following your video made it fairly easy! Thanks brother! 👍
@mouzaza70
3 жыл бұрын
I couldn't Ritch the flasher behind the dash . Need help
@mouzaza70
3 жыл бұрын
Can't doit
@thomasgardner5872
3 ай бұрын
Thank you for this video , did the switchback then needed relay , you saved me a lot of work , Thank you Sir
@emmettrowe5164
3 жыл бұрын
I would like to see this my good friend this is EMMETT... you should always test those bulbs LED bulbs and what have you before you complete the installation because if you have put the bulb in wrong the light will not come on I have already viewed some videos showing that happening so when doing so always leave the bulb out and test it to make sure it comes on before you complete the install or you will have to take everything apart again just to pull out the bulb and turn it around to make better contact ..and then test it again..to make sure..BECAUSE you did not do this before you put the mirror back together..
@ManJunk427
5 жыл бұрын
The hardest part of this. Is getting that Phillips screw out from under the mirror, without stripping it. It's torqued down pretty damn good. Absolutely make sure you have a new ,well fitting Phillips head...or you will strip it and be really mad at yourself and the guy who decided to use a Phillips there... instead of a torx.
@fr8hauler
6 жыл бұрын
Chris, THANK YOU!!! I just put the LED flasher in my '06 Wing. So glad I came across your vid because instructions said to pull windshield panel. I would never have pulled up that instrument panel without seeing it on yours. My flasher was very easy to get to once the panel was swiveled up. 2006 may be slightly different than yours or I have less options than you, but I was pleasantly surprised to see the flasher right behind the instrument cluster. Once again, thank you!
@phillipvazquez284
6 жыл бұрын
is it the same on a 2005
@doogey420
5 жыл бұрын
I just read this, very interesting I was just trying to find out from the man himself if any differences could be noticed in the 2nd and 3rd gen. Great info that the flasher is going to be easier to install under navi my 2008.
@doogey420
5 жыл бұрын
@@phillipvazquez284 First generation requires you to disconnect a wire that comes directly out of built in flasher box then rewire led flasher with proper honda fitting connector to reconnect to it. Better to find video on here. Where I saw it. KZitem.
@doogey420
5 жыл бұрын
Does your bike have navi?
@phillipvazquez284
5 жыл бұрын
@@doogey420 yes I did that along time ago thank you yes with Chris and cruiseman help I did it
@arthurmacklinsr7016
6 жыл бұрын
Well just added these to my wish list. upgrading my 2009 low beam to HID with delay, Lower cowl Leds, and with led flasher should be no more blind spots! Thanks C.C.
@djclover1447
5 ай бұрын
Thanks for the review and install. I just ordered some for my 2008.
@stevemathers2038
6 жыл бұрын
these videos seal the deal on my owning a GoldWing! !
@exmary2
5 жыл бұрын
Hi Chis, I followed your instructions to the letter and thanks by the way for finding an easier way to install these lights. When I installed the flasher, I noticed the white LED light would cancel but the amber turn signal would not activate. I re-installed the OEM flasher and all the lights worked fine except that they were flashing too fast...Bad flasher in the kit you think?
@MrMegacoffee
6 жыл бұрын
Nice upgrade. Just a fantastic safety extra.
@chriscaliente5033
6 жыл бұрын
Coffee Hutchins thanks it’s all for safety and visibility.
@da72ma
3 жыл бұрын
Through the front and that window gets a loving treatment. If you go through the dash change the speakers. I like Electrical Connections products but I went with the Pathfinders this time. All are great products. Please though spent the money for quality parts folks and avoid the cheap stuff from Amazon and eBay.
@antoniozephyr79
Жыл бұрын
Great video ,helps me a lot...thank you
@copdwarriormcdonald7968
6 жыл бұрын
Now thats how they do it! Nice looking front stance, I always say better seen than Not! Thanks for the great videos! CC Rider, Motorman out
@wendellchenault4031
6 жыл бұрын
Chris, wish I had seen your video sooner. I purchased the Dynamic Sequential LED lights for my 2016. According to their video you have to take the front nose piece off to run the wiring system and the flasher is optional. They also change the flasher from the front after removing the windshield and loosening the dash speaker cover. Problem is getting to the flasher to change it out. They do not show going in from the dash to replace the flasher. Think I may take my dash on apart and do it the way you did. Going in from the front I have had much difficulty unplugging the wires from the flasher. Question about the lights you used. On the ones I have when I use my key fob to lock up my bike the front boi pers do not blink like tney used to. Also, when the key is turned to accessories to listen to the radio, the blinker lights come on. Does this occur with the lights you used? Thanks in advance.
@mouzaza70
3 жыл бұрын
Can't Ritch flasher from the dashboard
@Viper6-MotoVlogger
6 жыл бұрын
A lot of work but well worth it. Looks good bro.
@chriscaliente5033
6 жыл бұрын
vac0002 thanks hopefully this video helps some out.
@VK-zt6sw
Жыл бұрын
Such an awesome video - thank you!
@doogey420
5 жыл бұрын
Hey Chris was wondering if the led install for the flasher will be any different on second generation 2008 gl1800? I guess what I'm asking is should I take it from the front or will it be easier for me to do it as you did from the writers position or the rear underneath of the Navi, and is there any differences in 2nd and third generation navi configuration? Like taking it apart and so on? Thank you for your time. Douglas
@mshippe61
6 жыл бұрын
Awesome Goldwing, love the LED lights.
@chriscaliente5033
6 жыл бұрын
Thanks.
@pedroc6823
6 жыл бұрын
Saving this comment for that day that is around the corner. You know you will.
@chriscaliente5033
6 жыл бұрын
Lol Pedro you cracks my side, and make my day.
@chrisclysdale5437
2 жыл бұрын
Did you also add switch backs to the fog lights at the same time? I noticed that your fog lights are also switchbacks.
@texaspete2k11
Жыл бұрын
As I watched this, I was told today a flasher switch replacement isn't required. I was told it was plug and play.
@MrMegacoffee
6 жыл бұрын
I need to get this for my bike. soon . good stuff.
@chriscaliente5033
6 жыл бұрын
Coffee Hutchins or you can buy a new 2018 Goldwing, and pay for a all new accessories, lol.
@Bass.Player
5 жыл бұрын
I did all of this except I went through the front to access the relay
@mouzaza70
3 жыл бұрын
Could not do it from the dashboard
@mouzaza70
3 жыл бұрын
Hi
@servantleader9487
2 жыл бұрын
Chris have you had any problems with the driving light turn signals having a yellow/orange tint after using the turn signal? I have all LED lights in my 2015 gl 1800, but have yet to replace the LED flasher. I hope installing will fix the problem.
@VictorMMartin
6 жыл бұрын
That looks tight up in there. What year is your bike? I'm thinking about doing this buy I'm not sure whether to get to the flasher from the front or the way you did it. Is that a 3 pin connector?
@OynxBlack
5 жыл бұрын
how did you get the fog lights at the bottom to switch as well?
@michaelfrascati7610
3 жыл бұрын
Same question here! (Flash)
@BobSmith-gh1xh
2 жыл бұрын
@@michaelfrascati7610 you have to have a special wiring adapter on the mirrors, run wiring down the fairing to the fog lights, in the Show Chrome fog light kit
@eddbell8719
3 жыл бұрын
I installed LED bulbs front and back on my 03 gl1800 when I turn on the right turn signal the left light goes out and when I turn the left turn signal the right goes out! So at any given time I only have one park light on in the front! What's the problem I'm really getting frustrated with this!
@tomzigterman8148
4 жыл бұрын
Hi Chris: thanks for the video! I'm changing out my flasher - what did you do with the old flasher, which apparently is connected to other wiring, just leave it there? -Tom
@gauteberg1351
3 жыл бұрын
pathfinder rele is not waterproof, after 5 year is it defeckt. i put the new rele in the mirror hause. extension wire from orginal place:-)
@harveyhollins7160
5 жыл бұрын
Chris: Can you switch the regular turn signal mirror bulb to the switch back bulb with switching the amber housing Harvey
@davidtoney9933
3 жыл бұрын
I have my dash up and I have looked and looked and do not see where this LED turn signal connection will go (2006 Goldwing) - any suggestions would be greatly appreciated.
@allenellis8188
6 жыл бұрын
They look great. About what was the cost? That maybe our next project
@chriscaliente5033
6 жыл бұрын
Allen Ellis the kit for switch back front turn signals were just over $100 bucks, it also comes with the LED flasher.
@DorianCot
4 жыл бұрын
Hi Chris. How did you connect the fog lamps with the turn signal ?
@RichWomack
5 жыл бұрын
Did the auto cancel on your turn signals still work after swapping out the lights and relay?
@EXCALIBURUS187
6 жыл бұрын
Good job chris
@chriscaliente5033
6 жыл бұрын
MICHAEL BRADDOCK thanks.
@luchorodriguez23
6 жыл бұрын
i have one and i am very happy with then
@fahadalzarooni716
6 жыл бұрын
Hi Chris, What is your feed back so far about this product? And i got the smoked lens. can I order the bulb and the flasher only. thank you for your help in advance.
@dr.k.3425
6 жыл бұрын
Hey Chris how hard was it to remove the dash? Love the lights man!
@chriscaliente5033
6 жыл бұрын
Markcus Kitchens after removing the speaker grill, it’s only 4 bolts then lifting the dash is easy.
@chrisdanforth2061
6 жыл бұрын
Hey Chris, do you have a video showing the removal of the speaker grill?
@mouzaza70
3 жыл бұрын
Hard to Ritch the flasher....need help.tks
@ThanhTran-pv4kl
6 жыл бұрын
Nice work!!
@chriscaliente5033
6 жыл бұрын
Thanh Tran thanks for the compliment.
@gtspeed927
5 жыл бұрын
What brand and item number is that radar detector? Is it waterproof?
@hyoungkyoukim4800
5 жыл бұрын
Great .. Thanks 👍
@mouzaza70
3 жыл бұрын
Hard to get it
@southpawsgarage
6 жыл бұрын
NICE!!
@anthonywing-man1450
6 жыл бұрын
Just wondering if you have access to a coupon code I could use
@mouzaza70
3 жыл бұрын
Hard to rich it
@pedroc6823
6 жыл бұрын
What a shame all that work just to get the new 18 GW.🤣🤣😂
@chriscaliente5033
6 жыл бұрын
LOL that’s a good one Pedro, but you are 100% incorrect.
@ghost9119
3 жыл бұрын
Which way consider is the easy way. From front of the bike taking off windshield off or your way !
Пікірлер: 77