Followed the step-by-step instructions for my Pixel 7 Pro (it really doesn't matter that the demo vid uses a different phone) and it worked perfectly. Rescanned my fingerprints as suggested but actually didn't need to as the original scans still worked fine, even with the new protector on. No issues with 'glue spilling everywhere' as I installed on a flat surface. I've tried so many screen protectors for my Pixel phones over the years and none have worked that well (especially the 'use water to apply' ones which are just awful). This is by far the best protector I've had for my Pixel 7 Pro and I'm really pleased with the result.
@mighty644
Жыл бұрын
What about the Glue that part concerns me the other screens protector simply had adhesive on the back. Will the glue be an issue if you need to remove the screen protector to replace in the future?
@leekrawczyk
Жыл бұрын
@@mighty644 I've not had to replace it on my phone yet so honestly can't answer I'm afraid. It's not 'super glue' strength though and personally wasn't a concern for me when applied. If I do ever have to replace the protector I'll be sure to update the review. For the record, still no complaints so far regarding how well it's protecting my screen.
@dillcowy
11 ай бұрын
Tutorial worked perfect for Pixel 7 XL Pro. Main takeaways are use all the glue in the direct center and push the screen up once it's fully glued. If you get that step right everything else should be easy. You don't have to use the razor or cover the receivers. But if you want to cover the receivers use the random stickers that came with it. 1. I turned my phone off and put it in the holder really quickly so it wouldn't turn on by the foam rollers, to avoid distracting screen turning on or vibrating the liquid glue. 2. Use all the glue and in the direct center of the phone. 3. Slowly drop the screen cover, you should not have to push down on it at all. Gravity will do all the work automatically to the whole screen perfectly. 4. Once whole screen is covered with glue push the screen up like it shows at 2:25. (don't skip this step). 5. 90 Seconds of UV light, pull phone out of case. 60 seconds of UV lights on each side and you're good to go. This protector is a little thick and you will need to re add you fingerprints AFTER you enable screen-protector mode.
@JadeMonkee
Жыл бұрын
Worked a treat, thanks! I used the black stickers in the pack to cover up the charging port and speakers at the bottom plus the mic and 5G aerial at the top. The knife I used to cut away the foam bumpers (as they'd gotten glue on them) from the frame afterwards. I ended up getting an air bubble caught in my first attempt (from removing the shim too quickly), so had to remove and apply a new one. I hadn't yet started the UV curing, so it was easy to wipe off all the runny glue, then just start over. The screen protector looks and feels great. Highly recommended!
@kingvinoda3896
Жыл бұрын
The instructions on the box say to apply just two drops of glue at two places on the screen. Unlike the video that used a lot of glue. I messed it up because I didn't use enough glue but that's only because the instructions were incorrect.
@thesmartI
8 ай бұрын
Yeah you gotta drench the screen and make sure liquid is everywhere
@l3inLaden
11 ай бұрын
Screen protectors are great, my only advice when installing it is make sure to take your time with putting the screen on with the glue, make sure there is absolutely no air bubbles, you can pull the screen back up and push the bubbles out, you cannot work with any of the bubbles after the product is cured so taking extra time for this step is key to a flawless result! Good luck
@AnastasijaKorsakova
11 ай бұрын
Works amazing! So far the best scrren protector i have had!
@hashman27
Жыл бұрын
I just applied this protector on a pixel 7 pro. The process is identical to this video. The glue is peculiar. It's very runny and fluid. When you squirt the glue onto the phone, the glue droplets seem to be attracted to each other and move towards each other to form a large pool in the middle of your phone. I thought my surface was flat, but it was off by 1-2mm and the glue started to roll towards the edge of the phone - I had to quickly adjust the phone and slide something underneath it to level it out. I would advise to get a spirit meter and ensure the surface is level before you pour the glue, it slides around and could easily fall off the edge. But once I had a steady and large pool of glue in the middle of the phone, I put the screen cover on just like in the video, and the glue spread beautifully. There was a small area at the top of the phone where it didn't reach immediately, but within a minute or so even that got covered. Really great coverage. The UV light thing was a surprise, but I did it for 2 minutes (as per the box instructions) and additional 1 minute per side like in the video. Anyway, the cover is beautiful. Well attached, crystal clear, responsive. Worth doing the extra few steps to get a screen cover this quality. I didn't need to use the guide stickers at all, and I didn't have to use the included mini switchblade.
@lukabacca
Жыл бұрын
My installation was a complete trainwreck, the glue started spreading from the top, resulting in a big air bubble in the middle lower part of the screen, i ended up squidging it away little by little until it was gone, glue fell out kinda everywhere but didn't get into buttons and ports fortunately, then i cured, cleaned and it looks as good as new, i understand it was user fault in my case, it ended up taking 1h30 to do, but the result is incredible, didnt even need to recalibrate the fingerprint sensor
@knotingo
Жыл бұрын
"premium tempered glass" is printed on the packaging. I wonder what the premium stands for. Currently, I can only determine the price for it. The glass is definitely not premium. My three delivered ones already had very fine scratches on the side, which you later operate with your finger. The attachment itself was very easy. But it is impossible to attach the glass dust-free. Unfortunately, I don't have a laboratory at home, which is hermetically sealed off from dust. All three glasses are now roasted because I really wanted to get it dust-free, just like with the adhesive protective glasses. Unfortunately without success. I just leave the last glass on it now, even if the fat dust grain in the middle bothers me. After all, better than no protection at all.
@marcelsmit4655
7 ай бұрын
its easy to use. just take your time and watch this video first. can't believe some people use just 2 drops of "glue". everything in the box comes in 3. its obvious you have to use the complete cartridge of glue. don't look at the text on the box. watch the video. 1st time went great. no bubbles, no dust, glue spread just fine. no need to rescan the fingerprint reader. i doubled the time with the UV light. just to be save.
@ColinStevens
Жыл бұрын
The video is great. I would warn anyone with an OtterBox case, its a tight fit, let the glue dry completely first. The curing with the light doesn't dry it completely. I was able to salvage it, no problem.
@travismcmillan7569
Жыл бұрын
For example if you crack the tempered glass will the phone under the screen be covered in glue
@andreahinze1348
Жыл бұрын
Worked fine but glass for pixel 7 pro is to small sadly. Hoped for a full protection.
@mikef767
Жыл бұрын
I just installed this on my pixel 7 pro and it was easy and looks great. One very very tiny air bubble that you have to look really hard to see
@codymaclean3369
Жыл бұрын
Make sure you have a level surface, half my glue poored over the side and my first attempt was over before it bag. I proceeded to try to add more glue, so now 2/3 are toast.
@JeannineFoss
Ай бұрын
What is the little razor blade for?
@francklag5295
Жыл бұрын
Just got one of these. I wonder how hard it would be to remove this screen if it ever gets damaged. How hard is the glue after curing?
@crBudgetWatches
Жыл бұрын
It's easy to remove just slide a thin paper card or a dental floss in one of the borders . If for some reason the glass protector is hard to remove you can use a shaving razor and hand soap it's easy to do.
@ZILLA....
2 күн бұрын
Just took mine off after a year and it came off easier and cleaner than any other plastic or glass screen protector i've used in the past. It was still good when I took it off , only that one corner was bubbling where i dropped my phone. only here to watch the video again to refresh my memory lol
@jeremykorzeniowski5654
Жыл бұрын
The protector I have came with a tempered glass protector for the cameras. Is this glued on as well? I have guide stickers and long black stickers as well with no reference to them in the video.
@marnih
Жыл бұрын
Took us 2 tries. Use plenty of the glue! Our first round we put what i thought was a bunch, but it didn't quite fill in the ends. Stinks wasting one. Pretty complicated process, hopefully it lasts well.
@zeynebnursahin514
3 ай бұрын
I applied exactly how you explained, thank you:) however now I need to recover because it has been broken after it felt down, so how can I remove and renew it?
@N4tur4lb0rnch1ll4
2 ай бұрын
You can just remove it like any other protector. Fingernail under one corner and slowly push it up
@ffBkLee
7 ай бұрын
What does one do with excessive glue leaking out?
@wagnermoreira786
Жыл бұрын
is it normal to not have glue spread to cover the whole screen?
@jstsms
11 ай бұрын
Does anybody know if this screen protector is compatible with a mous case on pixel 7 pro ?? Thanks
@yensed90
Жыл бұрын
Make sure to cover your Mic and Speaker ports. That Glue will Ruin your device.
@ozgday7171
Жыл бұрын
I'm stuck at 2:30. The glue ran EVERYWHERE. i put the screen on and there are air bubbles. HELP!!
@earlgrey1745
Жыл бұрын
great tutorial, screen protector is flawless.
@Ms.Tee.
Жыл бұрын
After installing, my finger is not reading my the phone. Don't know what to do. Good case though
@monrose7
Жыл бұрын
We're you able to fix the finger print sensor problem?
@Ms.Tee.
Жыл бұрын
@@monrose7 hi yes! There was a plastic that was attached on the finger print area lol..once removed, it worked. Make sure u do ur finger print scan first before putting the screen protector..it will make ur life easier...
@SteveBarak
Жыл бұрын
Nope. I am pretty good at careful small work, AND I watched this video many times, but I was unable to get this screen protector right. On the first protector, when I positioned it according to directions, the yellow bumper at the top end protruded just a tiny bit, and so the glass almost invisibly protruded a tiny bit at the bottom. And so when I put the phone in my case, the screen protector lifted a lot, and made it horrible. I have just tried to fit another one again, and I thought it was 100%... UNTIL, after curing with ultraviolet light, when I took the phone out of the supplied positioning holder, to my shock I discovered that the supplied glue had stuck to the edge of the glass. Leaving me with a bubbled imperfect screen protector on the edge with glue. I am not happy. The box stated that "99.99% customer who failed to apply the screen protector are not watching the video before installation". I watched and watch... and failed to get a good result. I suggest caution.
@dr.pcdilorenzocristofori
Жыл бұрын
TOP TOP TOP!
@jamaalspencer9712
Жыл бұрын
Hey... That's not a Pixel. Do you know of a good screen protector for the Pixel? What brand is the screen protector you're using in this video?
@aivensu8495
Жыл бұрын
Ni-shen . we sell this product on amazon
@fallen4life080
Жыл бұрын
I just ordered from them from Amazon, and just installed it on my Pixel 7 pro. The video linked with the kit they send you sends you here but the process is exactly the same. It works BEAUTIFULLY!
@wqwave
Жыл бұрын
@@aivensu8495 hi can you send me the link
@cozalenko7-341
2 жыл бұрын
What screen protector is this?
@aivensu8495
Жыл бұрын
it is an installtion video for Google pixel UV screen protector
@radtkinger
Жыл бұрын
uninstall video please 😉😝
@abusadatmohammadsayem1311
Жыл бұрын
Would not recommend buying it . Watched the videos. The glue spills over the plastic body. And it does not spread completely. Used 2 glasses already but still the glue inside the glass. Not worth the money I spent
Пікірлер: 48